And don’t forget those aftermarket front axles on the W204. We just went through that on one;) Vibration due to the aftermarket right front axle. Same exact sensation as the worn engine mounts.

@MasterTechLou

Жыл бұрын

Pinned! ❤️

@Hello_Kitty1661

11 ай бұрын

Hi thanks for the video i had my engine mounts replaced on my toyota celica but the car still has A bit of vibration another mechanic has told me the engine mount is after market ones any suggestion what can be done thanks

Dude.. super useful content. Instant subscription. Short, to the point, clear... Love it. Cheers

Seasons greetings Lou. Great diagnosis tip and one I could have definitely used in the past to remove doubt. Thanks Lou. 🙏

@MasterTechLou

Жыл бұрын

Thanks 😊 and seasons greeting to you as well!

Merry christmas boss! 2014 c250 owner here from the app, ur amazing helped me fixed an ongoing problem of 2 years

@MasterTechLou

Жыл бұрын

Merry Christmas to you as well my friend glad I could help!

Iv just started checkin them this way, much easier Thanx 4 sharing that tip

Great and simple video Bro. Great Job

Wow thank you so much for this video. I was able to diagnose the engine vibration on my Prius. As soon as I lifted the engine, the vibration and noise went away. Thank God it wasn't a bent piston rod, out of balance harmonic balancer or bad ignition coils. Woohoo!

Well described. I replaced all four mounts about 3 months ago and now vibrating again. I will try your method to pinpoint the bad mount.👍

@bushikciwa

3 ай бұрын

Sounds like maybe you didn’t plug in your vacuum lines into the mounts if applicable

@KollynJ

3 ай бұрын

What was it for you??

Lovely, intelligent, succinct video!!! RF engine mount is toast, Trans mount is beyond tired, and LF engine mount is probably "okay" I would replace all 3 only after I fixed that oil leak, otherwise the new RF engine mount will be headed for early retirement too!

Very helpful. Thanks.

thank you sir !!! you are a life & peggy bank savior 🎉😂 I was about to get scammed and your short, well explained video saved me from that. I can't thank you enough bro. 😊

@MasterTechLou

9 ай бұрын

Scammed how so? And thanks for the nice comments. Im just tryin to help.

Thanks for another "Good Tips" video!

@MasterTechLou

Жыл бұрын

Thank you I appreciate that! And Merry Christmas if you celebrate 🎉

Great video. Thaks for making it.

Thank you for the information 😊

Thanks bro u just helped me confirm what's wrong wit r car

Great tip. Since these mounts are essentially "wear items", I wonder why they don't show on the maintenance schedule for vehicles? I suppose their failure time doesn't necessarily correlate with mileage, does it? Most will have a schedule to replace the timing chain or belt (and ought to say have the garage replace the water pump while they have it torn all apart). I do think engine and transmission mounts are annual inspection points in my state, so they should be getting checked. My local garage will do a $100 used car evaluation, and these, u-joints/CV joints, struts, and some other gotchas people never think of are on their list. They include a quote to mediate any found issues. They will also give you a deal on a baseline maintenance package so you're aware of exactly when the last time everything was done.

@Ysl_kidd

10 ай бұрын

Lol $100 used car valuation ? That’s horrible, that service should be free.. a smog place tried to do to me and I drove off so quick 😂

hi i replace on my w204 diesel 2013 c class engine mount aftermarket one and vibration gone but when i brake i have a clunking noise on the left side it migt be the mount or somethinge else ? before the car wa fine no noisy at all thank for your time and effort

Thank you...well done!

Merry Christmas 🎄 🎅 🌲 Master Tech lou My teacher Master Tech lou Thanks👍 From Nick Ayivor from London England UK 🇬🇧

Hi thank you for the video

Great video

Thanks for this.

Thank you so much!

My 2004 Grand Cherokee 4.7 does that on the passenger side when you jack it up the middle part moves all the way up its basically a Bluetooth mount I think that explains why the engines sounds louder(not ticking or knocking and not squealing) it has a rumble sound especially when you're inside the cabin especially when accelerating

@MasterTechLou

8 күн бұрын

Motor mounts not only hold the engine, keep the engine secure, but also minimize the harmonics from the engine through the body

@justindaniels17

8 күн бұрын

@@MasterTechLou but can bad engine mount make a rumbling sound?

GREAT TIP!!!!!!

Thank you for this video! It clearly demonstrates the problem. I guess engine mounts are pita to change, that's why ppl don't replace them till it's past due for a long time. On my W140 in order to get to the mounts you need to remove tons of other parts. Plus I don't have a lift. I think both engine mounts should be replaced when one fails. It's easier to do both when car is lifted. Please tell me what would be the average price to replace both engine mounts and transmission mount on that white Benz?

@MasterTechLou

Жыл бұрын

Hello! For this white Benz it it can run just under 1k$ at dealer pricing. Rough guess as no two dealers have to nor will charge the same. These are easy , some can get up to 1500$

@yolo-cars

Жыл бұрын

@@MasterTechLou Thank you! Pricey a bit, but fortunately you don't need to change mounts too often...

Thank you

How much u charge usually for motor mounts

Make sense. Thanks

Thank your awesome

Hi can you please help me out on this one i have Replace all Engine Mount on Mazda 6 2006 and the car body still vibration only when it's in gear what do you think i should do next thank you

Outstanding

I bought after market strut arm mount with balance its shaking constantly never did it before I change it could it be the balance?

thank you for the awesome info.

I had all 3 mounts changed on my 2018 durango GT but I still feel vibration when idle should I change transmission mount again?

Great video for sure thanks for sharing, Unfortunately, I replaced all three motor mounts and one tranny mount on my Toyota Corolla and there is still have vibrating in the car and I hear a clicking noise whenever I turn the steering wheel left or right, I replaced the swaybar end links as well. The problem is so frustrating i Just can’t seem to figure it out. Any ideas of what it could be? Thanks again.

@MasterTechLou

5 ай бұрын

Vibrating can also be the engine not running correctly, clicking noises when turning can be strut mounts or Just something rubbing in the steering column. Noises are the easiest to figure out as you can use a stethoscope and or just feel the parts as someone Is rotating the wheel. As long as a problem is consistent its super easy to find. Loose bolts can make clicking, worn control arm bushing, rusted ball joints, thats why using a stethoscope is best.

What are the insulators for?

Thx!

Speciallized in shock absorber supports, engine supports, transmission supports since 2008,please contact if needing

And what would be the cost to get something like that fixed on a 2009 Nissan Murano

I just found out my X3 needs motor mounts good thing I have a warranty!

on a Volvo S80 D5 can we use aftermarket engine mounts? for instance Lemförder or Febi or Meyle . original is too expensive here

@MasterTechLou

6 ай бұрын

I don’t have that answer as I have not tried every aftermarket or brand name not sold through the dealer. But in my experience aftermarket does not work as well as oem. And from what I have learned is the parts sold through dealers is not the same as the same brand name sold through a parts store. So best I can say is make the best decision or keep looking for information saying they are a good product.

For this diesel car, does the dpf or something else have to come out? The passenger side doesn't fit to get out. Driver side is no issue. W212 E350 bluetec. Thanks in advance!

@MasterTechLou

Жыл бұрын

yes exhaust has to come out. if memory serves.

Help me out. I have a 2003 Mitsubishi Galant 2.4. Didn't have much of a vibration before but engine mounts were old. I replaced them now have a terrible cabin vibration especially when in gear. I also have developed a wobble when given gas. That may be because of me shifting that motor and transmission up and down. Can you give me your thoughts?

@MasterTechLou

Жыл бұрын

I will say aftermarket motor mounts are not as good as dealer mounts. Also you may need to loosen them and rev and rock the engine to get them to Settle. But if you got aftermarket mounts, that may have made it worse than worn oem. Wobble feeling on acceleration is usually cv axle Related but if non of this was There before doing the work, then you have your answer.

How about you tell me where you got that floor, which manufacturer, how it's holding up, pros, and cons., and how much was it? Thanks,

@MasterTechLou

6 ай бұрын

Swiss trax, I would recommend the solid floors if you have no floor drains and lift cars. The slit design is fine, but would prefer solid for under a car.

Thank you for the video! Can i ask for your advice? I have a 2002 Volvo s40. It usually runs smooth, but only when i come from the highway and i have to brake a bit more firmly, the engine starts shaking, revs change between 700rpm and 1100 rpm. The engine even shut off a few times when it happend. I tried to bring it to the dealer, but they couldn't find anything (no engine light). Do you have any advice? Thank you! Edit: it's a manual with an 1.8 petrol engine.

@MasterTechLou

7 ай бұрын

Its most likely a bad leaking brake Booster. You are getting too much vacuum loss so the engine is dying. That is my first thing I would check.

@marijnsamuels

7 ай бұрын

@@MasterTechLou thank you for the response, I wil get that checked. I hope not, because that will cost me about 700 euro's to replace I found out. I bought the car a year ago voor 800 :')

@MasterTechLou

7 ай бұрын

@@marijnsamuels cars are a loss. Necessary expenses to get where you need to be.

The engine in my 2003 nissan frontier is vibrating excessively with a slight rattling noise while idling but only in drive or reverse, is worse with the air conditioning on, in park or neutral it is fine. I have never heard or felt anything at higher speeds. Is this a possible bad engine mount? Any suggestions would be apprecitated, thank you

@MasterTechLou

10 ай бұрын

Bad engine mount maybe, but would not matter with ac on or off. might have ac issue, take engine belt off and run just for a few minutes see if anything changes, if it does you may have issues with a pulley or ac compressor.

@bwayne4479

5 ай бұрын

​@MasterTechLou same issue as @chriss920 but I've already replaced ac compressor, idler pulley, and tensioner pulley. Noise still there. Thoughts? 2012 buick regal gs.

Do you generally find that for cars 10-15 years old, if one mount has gone bad, most or all of the mounts need to be replaced?

@MasterTechLou

3 күн бұрын

Absolutely, if one has age and failed the others are there or right behind it. Problem with owning the car the whole lifespan is as the vibrations get worse you are immune to it because it becomes normal. Until you drive another car then get back In yours then are like “what did you do to my car” 🫣😂

Do you have any tips for me, I got the new mount and new bolts but now I can only get one bolt back in, the others won't line up, do I need to readjust where my jack is? I don't have a lift like yours just ramps and Jack's, no one locally or even regionally will fix it so I'm left to do it myself

@MasterTechLou

3 ай бұрын

Not sure what youre working on but prybars and raising and lowering the engine can help. Or ratchet straps

@zzzroxyzzz

3 ай бұрын

@@MasterTechLou it's just a motor mount on my smart car, Mercedes parts that's why it led me to your vid

Why do motor mounts go out so quickly????? I replaced all 5 in the honda 2005 crv two months ago and now have to replace again due to vibration....it has 300 thosand on mileage...i drive it on rural carrier route everyday....any ideas....

@MasterTechLou

8 ай бұрын

Hello, well, if they are not oem mounts from the dealer it can be the reason, or you have other issues. Like timing issues causing engine vibrations or worn harmonic balancer causing vibrations.

Clio 1.2 front wheel drive. 3 mount points. Replaced the top engine end mount and the rear/dogbone because I had a vibration. Didnt cure it and if anything made it worse. Gonna try the gearbox top mount. If that doesnt solve it... what would?

@MasterTechLou

9 ай бұрын

If replacing a mount made it worse then you are on the right track with maybe the wrong parts. Or if you tighten down mounts while they are under tension you can cause vibrations. We often loosen mounts and rev the engine to settle them

@andyrantshumanphilosopher7571

9 ай бұрын

@@MasterTechLou do you loosen all 3 at the same time, or individually?

@MasterTechLou

9 ай бұрын

@@andyrantshumanphilosopher7571 if front wheel drive its a little trickier as you do need to support the engine you just dont want the mounts under tension . So I would loosen the mounts and jack the engine and rock it to make sure its as relaxed as possible. Also I have yet to find motor mounts that are as good as the dealer ones.

How long can you drive on a bad motor mount? I just found out today both of my front are bad on my 2010 Infiniti G37x.

@MasterTechLou

2 ай бұрын

Forever. 🤷🏼‍♂️

Do you ever replace just the bad or worst ones?

@MasterTechLou

3 ай бұрын

Not usually, because then the weak ones can cause the new ones to tear or break

i have Tahoe 98 when i start A/C and put transmission in D in stop mode it's vibrating until i move and drive on the road with speed no problem ! and without A/C also no problem!

@MasterTechLou

10 күн бұрын

Probably low idle? Engine struggles to keep runnin. Might look into misfiring issue? Or possibly bad compressor or overcharged ac system

@Ana_Khalid

9 күн бұрын

@@MasterTechLou thanks my friend 🌹 please tell me what to do , because i did everything i cleaned throttle and sensor changed spark plugs but no use! however the engine is running perfect even it's almost 300k/m , I'm a new friend from KSA , appreciate your help.

I have a 2012 Honda civic it shakes under 45mph. Mostly when the speed limit is

@MasterTechLou

3 ай бұрын

Sounds like the torque converter for the transmission possibly

@lifegoes420

2 ай бұрын

Okay fuckin same, but on my 2020 Forte GT. Same exact thing.

My car is shaking and vibrating when ac is on and when I stopped and due to that it leads to the car just stop and not wanting to drive I have to turn it off completely and wait for a while until it can drive again what would you say is the reason ?

@MasterTechLou

2 ай бұрын

Either overcharging of the ac or the ac compressor is about to seize up

Change plug first too

My jetta only vibrates when i go above 60. Is that for sure bad motor mounts?

@MasterTechLou

Ай бұрын

No, torque converter, wheels, tires, brakes , loose steering components need looked at

What is the cost of that job, replacing all 3 mounts?

@MasterTechLou

14 сағат бұрын

Dealer price 1800-2500$, lots of variables.

😁👍

I lost 3 or so bolts to my mount and other 2 or 3 were loose. Car was JUMPING side to side violently when i braked.

@MasterTechLou

4 ай бұрын

Oh dang!

What could happen if i didn't change them? If vibration is lets say medium to high

@MasterTechLou

12 күн бұрын

Nothing. Just annoyance. Unless the mounts secure the engine from movement Which can wear and break wiring

@sethxtekken

11 күн бұрын

@@MasterTechLou thanks 🌹🌹

What if it rattles only when accelerating? How can I diagnose the problem

@MasterTechLou

3 ай бұрын

On jack stands with the drive wheels off the ground

gold

what about when I only feel vibration when the A/c is on?

@MasterTechLou

5 ай бұрын

Ac compressor or belt tensioner or alternator.

I found out today that I have a bad motor mount

Mercedes engine mounts love to break!

That car has bigger problems than mounts. Look at all that oil 😵

@MasterTechLou

11 ай бұрын

self rustproofing.

The first engine mount is the passenger side, thanks me later 😃

Wrong not all car have the same style motor mount , that jack isn’t always helpful

@MasterTechLou

2 ай бұрын

You’re wrong, all mounts have engine weight on them. Gravity always pulls down. I love how people like to say something is wrong yet never say what is right. Ya just want to say something negative.

@Sokren817

2 ай бұрын

@@MasterTechLou nope different car and model have mounts designed differently

@MasterTechLou

2 ай бұрын

@@Sokren817 ok ✅

I don't have a lift to elevate my car and look under it like that. Not very helpful.

@MasterTechLou

2 ай бұрын

its no different then using a jack and jack stands, do not make my video the problem, my video is the solution.

I am on the third engine mount on my 10 civic passenger main mount they collapes in less then 3 weeks all three i bought it at oreillys life time warranty so atleast i continue to get them free but im fed up .the rest of the mounts are ok can it be oreillys mounts are crap or can it be something else?they just fall flat touching top and bottom so car vibrates its weard they are all collasing lol any idea?anyone know of a good aftermarket brand ?honda brand is way to expensive

@MasterTechLou

4 ай бұрын

This is where you answered your own questions. It’s obvious its oriellys brand . The oem lasted this long, so you get what you pay for

@user-ly6hz4oe2n

4 ай бұрын

thank you ill buy original ill pay up lol

@MasterTechLou

4 ай бұрын

@@user-ly6hz4oe2n yeah only the ones that keep the engine from flopping forward and back could have other underlying issues, but when the mount just supports the engine, its usually quality thats the issue. So far in my dodge journey ive had good luck with O’Reilly’s mounts 🤞🏻, 2013 with 190k I just did a head gasket and upgraded and man, quite a difference although oem would be better but at $300 a mount its hard to throw that away just yet. I totally understand what you did but either try another manufacturer or got oem and move on . Sometimes you cant find a good quality aftermarket for a certain part. Win some lose some. Never win with cars anyway. So minimizing loss is best we can do 😂😩😂😩😂😩

Just missing a car lift 🥲

@MasterTechLou

3 күн бұрын

Same process with jack and jack stands.

@JonathanDiaz-vm5mb

3 күн бұрын

@@MasterTechLou yeah I mean it’s a lot easier with a lift lol