I'm from the Philippines and honestly you just saved my life. I had the same homework and only had 3 hours before deadline. I didn't know what to do until I encountered your video. I wish you were my teacher in my networking class instead.

@dipakbari4

2 жыл бұрын

Thank you Ken Kaneki for your kind words. I'm happy that this video was helpful to you and you've learned something from it.

Thank you for your informative video. I was struggling with one-armed router (router on a stick) config with VLANs in Packet Tracer but followed your examples and go it working 100% first time. Thanks again.

@dipakbari4

2 жыл бұрын

Great to hear!

You have clear steps and clear speaking calm voice that explains a very complex setup in a easy steps. Thank you.

@dipakbari4

2 жыл бұрын

You're very welcome!

Great video. No messing around straight to the point and clearly explaining what is happening.

@dipakbari4

4 ай бұрын

Thanks, glad to know it was helpful to you.

@Podracer1000

4 ай бұрын

@@dipakbari4 Dipak, Your video is almost exactly like an assignment I have for university (computer networks subject), so this is a god send for me. I was really confused about the IP range setting on the router (dot1q encapsulation) and you explained it great.

@dipakbari4

4 ай бұрын

@@Podracer1000 Yes, I understand. That part was really a bit confusing in networking classes. Especially, in primary stage of learning. I faced this too. 😂

Thanks! forgot what the commands and procedure i was taught in class today and this helped quite a bit.

@dipakbari4

2 жыл бұрын

Glad it helped!

Excellent tutorial. Thankyou for teaching me about sub interfaces

@dipakbari4

3 жыл бұрын

Glad you liked it!

Thank you very much I have now understood inter vlan routing perfectly

@dipakbari4

Жыл бұрын

You're welcome. 🙂

I m from the 🇱🇰 .specially thx u dear sir .goad bless you

@dipakbari4

4 ай бұрын

Thanks and welcome

Thanks for sharing fruitful knowledge with us.

@dipakbari4

2 жыл бұрын

You're welcome!

Thanks a lot! Really helped me out..

@dipakbari4

4 ай бұрын

Glad it helped!

yo this was mad helpful, thank you brother

@dipakbari4

2 жыл бұрын

You're welcome.

Thanks very much,now am done with my take away CAT❤️💯🎉

@dipakbari4

2 жыл бұрын

You're welcome.

Thanks you for sharing this Knowledge.

@dipakbari4

Жыл бұрын

You're welcome!

Lots of gratitude!

@dipakbari4

2 жыл бұрын

Happy to help!

Superb, It was really handy Thank U

@dipakbari4

3 жыл бұрын

Most welcome 😊

Thank u brother this helped me a lot.. God bless u

@dipakbari4

3 жыл бұрын

Glad it helped

Sir thank you thank you so much sir. Today your video helped me a lot sir. If I dont have your video I can't imagine my situation. I have lab tomorrow, if I dont have your video I will be failed in tomorrow lab. Thank you so much sir for uploading such a useful videos. Thank you sir. print(" Thank you "*100000)

@dipakbari4

2 жыл бұрын

You are most welcome

very nice video thanks man

@dipakbari4

Жыл бұрын

You're welcome. :-)

Thanks you very much.............Arokom Khola mele Tutorial Chai..............

@dipakbari4

4 жыл бұрын

You are most welcome

Awesome video 😊

@dipakbari4

3 ай бұрын

Thank you! Cheers!

THANK YOU SO MUCH!!!!

@dipakbari4

2 жыл бұрын

You're welcome. 🙂

good video ,make me to easy understand

@dipakbari4

Жыл бұрын

Glad you liked it!

Hi Dipak, thanks for this wonderful explain but am a little confuse, what ip was configured on the Router (default gateway or vlan ip address? Secondly is there another way of doing this configuration that allows the vlans to be configured with ip address and default gateway on the switch?

@dipakbari4

Жыл бұрын

1. VLAN ip address was there. 2. Try Layer 3 switch to avoid the implementation of Router to this scenario.

very useful brohh

@dipakbari4

2 жыл бұрын

Glad to hear that

Nice Explanation.Sir

@dipakbari4

3 жыл бұрын

Thanks and welcome

Thank u so much!!

@dipakbari4

3 жыл бұрын

You're welcome!

Thank you so much for the detailed explanation. Got one question?? When creating any subinterface, should the name of the interface be the same as the VLAN ID? Example: If I create vlan 50 then will the subinterface be created as “Interface fastethernet f0/0.50” or can the subinterface be “interface fastethernet f0/0.4”??

@dipakbari4

Жыл бұрын

Not necessarily, you may use any subinterface whatever you like to put. I gave for my convenience to demonstrate. So, other people learn it easily and nothing else.

thank you very much...

@dipakbari4

4 жыл бұрын

You're welcome. :-)

@juanangulo8178

4 жыл бұрын

@@dipakbari4 hola kiero contatarme contigo me podrias regalar tu numero

Idk if you will see this but how to configure if I have another 2 switch that contains 3 pcs with different vlans?

hello may i ask how will you put telnet on it?

Thank you for the great video! I am struggling on vlans and routers. I am happy creating Vlans on switches but I don't understand the concept of giving the Vlan an IP? Do I need to do it on every router??

@dipakbari4

11 ай бұрын

Glad the video helped you. Well in the case of Inter VLAN the IP address is required due to the segmentation of the different networks. As we know that the Switches work on the Layer 2 of the OSI reference model and the purpose of inter VLAN is to allow intercommunication of VLANs which is possible through a Layer 3 device(s) and protocol. But, if you are using L3 Switches then a router is not needed in that case.

@SamFenney-cr6df

11 ай бұрын

@@dipakbari4 Thank you so much for responding! In that case, if I wanted to give Vlan 20 an IP. Do I need to add it on every layer 3 switch?

thank u so much bari bhaiii

@dipakbari4

2 жыл бұрын

Always welcome

hi can you help me to understand a doubt about Interconnection of Vlan

Good video sir🙏🏽

@dipakbari4

2 жыл бұрын

You're welcome.

Thank vai..!🖤

@dipakbari4

2 жыл бұрын

You're welcome. 😃

How to communicate multi vlan in Same Subnet (network).

hi i assigned the command like interface gigabite 0/1.20 but it would be like 0/0.20 , so after assigning , how can i change it ??

@dipakbari4

2 жыл бұрын

just remove the ip from that interface and re-assign it. To remove ip address from a specific port use 'no ip' command there. Hope this will help you.

it is showing failed in every message pinging. What to do?

@dipakbari4

11 ай бұрын

Please check the configuration and follow along with the video.

Hello dear, I have some questions, when i command the show ip route it said the default gateway is not set? How and why?… thanks

@dipakbari4

Жыл бұрын

It maybe, you missed to set default gateway.

I have used the same command from beginning till the end.. Each and every step is crct.. But at the end ping test is failed... Why sir.. Pls reply ASAP... I am doing project on this... Tmrw I need to submit....

@dipakbari4

2 жыл бұрын

Hi. I guess you missed something or configured differently. I've linked the Packet Tracer file used in this recording, you can download it and compare it with your Packet Tracer file. I hope this will help you to figure out the issues you're facing with. All the best. 👍

Thanks bro

@dipakbari4

3 жыл бұрын

You're welcome.

@anuvasanthanp3489

3 жыл бұрын

Luv from Tamil nadu

Bro, I did same like you and have same configuration, but there is no ping reachability between VLAN 10 with other VLANs and vice versa. I can not upload .pkt file here, but I paste configuration here. Please help me to troubleshoot. Router Configuration: interface GigabitEthernet0/0.10 encapsulation dot1Q 10 ip address 192.168.10.1 255.255.255.0 ! interface GigabitEthernet0/0.20 encapsulation dot1Q 20 ip address 192.168.20.1 255.255.255.0 ! interface GigabitEthernet0/0.30 encapsulation dot1Q 30 ip address 192.168.30.1 255.255.255.0 Switch Configuration: interface FastEthernet0/1 switchport access vlan 10 switchport mode access ! interface FastEthernet0/2 switchport access vlan 20 switchport mode access ! interface FastEthernet0/3 switchport access vlan 30 switchport mode access ! interface FastEthernet0/4 ...... interface GigabitEthernet0/1 switchport mode trunk show vlans 10 HR active Fa0/1 20 IT active Fa0/2 30 FMD active Fa0/3 IP addresses to three pcs are 192.168.10.2,192.168.20.3,192.168.30.3

Makasih ngab

@dipakbari4

3 жыл бұрын

You're welcome.

What if I have to use /29 ? What IP can I use?

@dipakbari4

2 жыл бұрын

/29 defines the portion of ip address which would used by network

I didn't understand VLAN 10 with diff. IP ranges. 192.168.10.xx and 192.168.30.xx range.

@dipakbari4

4 жыл бұрын

For beginners it wasn't good to demonstrated too much deeply about it. I renamed the vlan 10 on 30 network with vlan 30, to easily understand the concept without making it complex. And also demonstrated the redundant assignment issue with vlan which was already assigned to the network. I'll use and will explain this things on the upcoming video. :-)

what is encapsulation and why we use in this configuration

@ganadesilva7788

2 жыл бұрын

here we using one router for 3 diffrent subnet addresses, so we have to divede the router into 3 ... encapsulation does this .... its means we teaching the router where those ip addresses are connected.

Whats inter Vlan routing

@dipakbari4

3 жыл бұрын

VLANs divide broadcast domains in a LAN environment. Whenever hosts in one VLAN need to communicate with hosts in another VLAN, the traffic must be routed between them. This is known as inter-VLAN routing. See the below link for detail information. www.cisco.com/c/en/us/support/docs/lan-switching/inter-vlan-routing/41860-howto-L3-intervlanrouting.html#:~:text=VLANs%20divide%20broadcast%20domains%20in,virtual%20interfaces%20(SVIs)%20).

What doe encapsulation dot1q mean?

@dipakbari4

2 жыл бұрын

It's a networking standard that defines there is Virtual Lans or VLANs on Ethernet Network.

Detailed explanation sir thanku learnt clearly nd can I have link for intra vlan also

@dipakbari4

4 жыл бұрын

Will upload soon

@dipakbari4

4 жыл бұрын

Check this out 👉👉 kzread.info/dash/bejne/nGukyLWgkq_ZfJM.html

I recall the inter vlan but here is many mistake while creating inter vlan but its good for me

@dipakbari4

2 жыл бұрын

They are intentionally given to troubleshoot.

@dipakbari4

2 жыл бұрын

Glad you liked it. 😊

Sir its failed...

Hey, everyone! 🙂 Hope you all guys are doing well. I've released an Android app 👉👉 IP Calculator 👈👈 for IP address calculation purposes. Designed for networking ⚡⚡ enthusiast. You can download 📱📱 this from Google Play 🏪 store. App link 👉👉 play.google.com/store/apps/details?id=com.technosoftlabs.ipcalculator Have a nice day. 😎

use TAB keys

bhai ek bar bna lete fir dalte video