Thanks for posting this lucid & helpful vid. As one who was in the trade for 30 years, I can vouch for the accuracy of this very helpful knowledge, without which you can be left stranded

You guys saved the day! Was able to save the boss some money and time with the first solution of tapping on the priming mechanism. Thanks!!!

@GOIndustrial

Жыл бұрын

Ah yes, so good to hear!

I just fixed my 695 MX ll by following your steps. Thank you !!

@GOIndustrial

7 ай бұрын

I'm so glad to hear! Thanks for watching.

Thank you so much! I was devastated as I went to start and no priming! Saved the day!😃

@GOIndustrial

2 жыл бұрын

HI Jennifer, thanks so much for your comment! Super happy the video could help 🙌

Brilliant and informative vid - priceless info as I was right in the mire. Sincere thanks 🙏🙏🙏

Good tech tips try use warm water and a hanfull of laundry powder mixed well to flush pump after use everytime, heaps better than water , then use atomex pump saver , to help stop this from happening , carby cleaner works well for cleaning inlet out quickly once removed.

@GOIndustrial

2 жыл бұрын

That's an awesome tip Corey, thanks for sharing. We always recommend Graco's Pump Armour however over other brands to keep in-check with best practice and adhering to warranty.

Very helpful thank you

I have Graco pron ×19, it is neither priming or building pressure to the gun.

I did all those steps and put a new prime valve still doesn’t prime ..

Ball not stuck. Suxks up material but won't prime. Any idea? New filters, pressure knob etc

Hey team, can you guys please do a review of the latest model 490 PC stand (smart control 3.0) and the 495 low boy. Really keen to see a video before purchasing it next week. Cheers

@GOIndustrial

3 жыл бұрын

Hey Ale, thanks for your comment, that sounds like a great idea - we already have one in the works, stay tuned!

Mine is priming fine but when I change it to come out the gun it goes dead. Tried changing the hose but it is still the same

Hi guys, my top check ball is stuck. Your vid is great for the cleaning the lower ball. Using a small pic I found the upper ball is stuck. How do I get the upper ball unstuck?

@GOIndustrial

Жыл бұрын

You can poke the upper ball with a very thin tool, like a screw driver or punch. Alternatively, you might have to disassemble the upper section of the pump to access the top ball. We will make a video on this troubleshooting step!

This video just saved me. Took it apart still wouldn't prime put it back together hit it with hammer and it started priming

@GOIndustrial

2 жыл бұрын

Hey Ricky, thanks for the comment! Glad to hear the video help get you out of trouble... sometimes the simplest things help the most haha

So my Graco 495 ultra max 2 low boy primes up but it once pressured up it stops running of course but if you let it set for a few minutes it cycles once then shuts off it does this every few minutes exactly like clock work What is causing it to do this? I’m guessing it’s dropping in pressure but why?

@GOIndustrial

2 жыл бұрын

Hi Jeremy, thanks for the great comment! This is completely normal and not something to worry about at all, it is just the machine jogging to ensure that there are no air cavitations on the line and that the pressure is still constant. You only need to start worrying if it doesn't stall when it reaches the pressure. Hope this helps!

Hi guys just want to ask i have a 490 airless sprayer when i turn the switch on the unit would not start at all smart control doesnt give me any fault code just a dotted line then after a few seconds it started to spark then smells burn what could be the problem im from the philippines thank you

@GOIndustrial

2 жыл бұрын

Hi Oyie, it sounds like you most likely are in need of a control board replacement. The sparks and smell you mention could be from bad power to the machine - if you are running off unstable power you to the Graco spray units, it is recommended that you use a surge protector. If the unit is new, you should return it to the place where you purchased and see if they can repair under warranty. If the unit is older then I would take it to the closest repairer for inspection. Hope this helps!

@kenvanmersbergen9403

Жыл бұрын

@@GOIndustrial mo

I loved my graco 490

@GOIndustrial

3 жыл бұрын

The Graco 490 is an absolute beast sprayer! 🤙🏼

my graco490 hi boy appears to be overheating yet motor doesn't feel hot. shuts off and doesn't come back on

@GOIndustrial

2 жыл бұрын

Hey Carmen, that definitely doesn't sound right - it could be either a faulty control board or motor. I'd recommend taking your 490 to a service centre and having them look at it. It should be covered under warranty if the motor is the fault. Hope this helps!

좋아요 구독누릅니다