Dude, best video on KZread! Thank you!

@GOIndustrial

Жыл бұрын

Thank you!!

Very good. Very helpful. Thanks.

@GOIndustrial

3 жыл бұрын

Hey Chong!! Thank you for your comment, happy we could help. :)

@MBSK-xw4ff

3 жыл бұрын

감사합니다

Awesome video thank you so much💪🏾

@GOIndustrial

2 жыл бұрын

Hey Sergio! Thanks for your comment, glad it helped! 🙌

I was surfing the KZread and like the way you put your packing in the best so I rate you no#1 especially when putting in the bottom packings do not to tighten them up until you push ROD through the piston cylinder great way to insure you don't tear up your new packing do a question do you need lock tight on the screw before tighten and what type thanks!

@GOIndustrial

3 жыл бұрын

Hi Russell, No Loctite is required, however, if you did want that extra peace of mind, this is a great Loctite we use for all our servicing www.bunnings.com.au/loctite-243-10ml-adhesive-threadlocker_p1560362

@MBSK-xw4ff

3 жыл бұрын

고맙습니다

THANKS

@GOIndustrial

2 жыл бұрын

Anytime Chris!

Hello, thanks for the lesson. How can I get the repair kits for 3400?

Great video thanks for sharing mate, how does the piston and seals get lubricated i noticed you poured oil through the top will this oil penetrate past the o rings? Will engine oil be ok to lubricate piston before assembly

@GOIndustrial

Жыл бұрын

Engine oil will be OK to lubricate the piston when repacking, I would recommend using 30W oil where you can. As for ongoing preventative maintenance and storage, Graco supplies a product called Throat Seal Liquid (TSL). This is formulated for the packings on the piston, and can be squeezed into the top of the packing nut before and after spraying. We highly recommend this oil.

@radj4719

Жыл бұрын

@@GOIndustrial thanks mate i appreciate your reply

Fantastic video! Thanks for making it. Maybe you can help solve my issue? After rebuilding the pump it still won't prime. You can hear the balls both moving freely and it's very clean inside. I've disconnected the line from the pump to the filter housing. Nothing comes out of the pump. You can feel some suction if you cover the intake hose connection with your hand. You can see the piston moving like it should, the motor sounds like it always has. I'm not sure what the issue is. Planning to call Graco tomorrow morning. Did you have any ideas?

@GOIndustrial

Жыл бұрын

Hey man! I would definitely look at your prime valve - this is the cause of the majority of priming issues. We've put together a video series below of troubleshooting these issues: How to replace your prime valve: kzread.info/dash/bejne/l4CmystyecnMhrQ.html&ab_channel=GOIndustrial Why to keep your sprayer in the 'spray position' - instagram.com/reel/CiR9iXsBQK2/ How to replace your prime valve (quick tutorial): instagram.com/reel/CO2AuJxh_Pv/ Let me know how you go! Try this first, as the pump is generally not the reason for priming difficulties (other than the check-balls getting stuck)

@dustinkarrick7819

Жыл бұрын

@@GOIndustrial Just bipassed the suction hose. (Put a cup of water directly under the pump and contiuned pouring water to keep it full. )The pump primes! It's an invisible break in the hose or O-Rings for it.

구독합니다

Hello, do you know if I could replace my Graco LineLazer V 3900 pump with a 5900 pump? Thank you.

@GOIndustrial

2 жыл бұрын

Hey, great comment! I looked up the parts manuals for both units and it looks like they have different part numbers for the pumps, so unfortunately, I don't think the 5900 pump will work on the 3900. What region are you from? I can try find the part number you need!

@KN-fk9lj

2 жыл бұрын

@@GOIndustrial Thank you!

Hardwood it have been to make the video from the beginning where you actually took the pump apart? Starting halfway through with the pump completely apart does nothing to show how the piston separates.

hello I have a 390 greco but when I turn it on it burns the fuse that fails it could have

@GOIndustrial

3 жыл бұрын

Hi Julio, thanks for your comment! I'd recommend taking this to your local Graco service centre as this could be a number of things from a faulty power lead to a faulty control board. Best of luck!

@MBSK-xw4ff

3 жыл бұрын

좋아요

좋아요

Show how you take off the piston plz

@GOIndustrial

3 жыл бұрын

Hi Xavier, Thank you for your feedback! We'll add pump removal to the list of videos to make, stay tuned!

Hello I have an old fireball pump. If I get model off it can you hook me up with rebuild kit.. Guy I let use it didnt use oil in it. It was used for oil spraying cars

@stephenc4161

2 жыл бұрын

Yeah sure!

@GOIndustrial

2 жыл бұрын

100% mate - please feel free to send us an email on sales@goind.com.au and we'll make it happen!

will it work on a em380?

@GOIndustrial

3 жыл бұрын

Hi Thor, this specific kit would not work on the em380. It is the same process to repair but the kit would be slightly different. I recommend contacting your closest Graco distributor!

@thorbradshaw2637

3 жыл бұрын

@@GOIndustrial thanks for the reply

베리굿나이스

Have you tried a tritech sprayer 😂

💦반갑습니다,수고하십니다,항상건겅하시고 복받으시길바랍니다,,,Elastic coating (탄성코트)work on veranda wall..............

@GOIndustrial

3 жыл бұрын

만나서 반갑습니다! 의견 감사합니다 :) 이 펌프는 탄성 코팅을 분사하기에는 조금 작을 수 있습니다. 더 큰 기계가 필요할 수도 있습니다. Graco 695 이상이 필요할 수도 있습니다. 이것이 도움이되기를 바라며 번역이 좋기를 바랍니다.

@MBSK-xw4ff

3 жыл бұрын

@@GOIndustrial 감사합니다

Greco pump Repair kit

@charlesrasquinha9915

Жыл бұрын

Greco pump x70 Repair kit

You spent zero time pointing out the packing and how there different on both sides ,

@michaelsoumelidis9332

Ай бұрын

Totally agree I’ve done this before you should’ve explain which way they go in