Repacking a Graco 490 airless sprayers. Subscribe below! Write in the comments below what sprayer you want me to fix next!
Жүктеу.....
Пікірлер: 25
@vintage-jm2fvАй бұрын
Awesome vid thx Canada Anyone who complains does not appreciate content creators/helpers do this out of kindness...
@davidbahr96123 жыл бұрын
I CANT THANK YOU ENOUGH MY MAN!!! No talking, clear visuals, helpful written reminders. Just perfect man, subbed
@almadi198614 жыл бұрын
Oh man, i don’t know what i would do without your video i was able to do the same thing just by watching your video You are amazing 🙏
@48hourpumprepair96
4 жыл бұрын
Glad I could help!
@juliozapata42314 жыл бұрын
You make it look so easy!!!!!!
@deniztolu304 жыл бұрын
Great video
@almadi198614 жыл бұрын
Great video thanks 😊
@ricardoalegria9416 Жыл бұрын
What model # repacking kit did you use?
@DavidMartinez-no6du7 ай бұрын
Thaksss
@amauriisai-OpTiimusZ3 жыл бұрын
what type of grease do you use ? and where do you get it at ?
@bryanthunders20463 ай бұрын
Approximately how tight should the piston valve be? I snugged it and gave it another half turn and it eventually came loose even with thread lock. Another time I tightened it pretty tight but it ripped my packings after a few uses? Help? Thanks!
@48hourpumprepair96
2 ай бұрын
You have to be careful, its a fine balance. I tighten just enough that the packing are not swelling out, and always use thread lock. And when you put the rod in the cylinder make sure you use LOTS of grease, it will help prevent the packings from getting sheared.
@juliocesarceron12733 жыл бұрын
hello I have a 390 greco but when I turn it on it burns the fuse that fails it could have
@48hourpumprepair96
3 жыл бұрын
Could be a bad board or motor.
@victor602flyaf3 жыл бұрын
hard to follow did you put tread locker or ??
@48hourpumprepair96
3 жыл бұрын
Thread lock on piston.
@johnnygarcia73033 жыл бұрын
What grease did you use?
@48hourpumprepair96
3 жыл бұрын
Red brake grease.
@WeThePeopleUnited2A6 ай бұрын
Didn’t show how the seals are supposed to go on the most important part
@MBSK-xw4ff3 жыл бұрын
💦반갑습니다,수고하십니다,항상건겅하시고 복받으시길바랍니다,,,Elastic coating (탄성코트)work on veranda wall..............
@dandawson6705 Жыл бұрын
What the hell was all that oil in the pump for? I’ve been a painting contractor for years and never have I seen black oil in a airless. Bizarre 😮😂😂😂
@redneckem1
11 ай бұрын
Dirty packing fluid?🤷🏻♂️
@montewestlund81953 жыл бұрын
no talking or explanation of what's going on, meh....
@ismaelarredondo394
Жыл бұрын
good video .. i did it i fixed the pump of my spraying machine
@luisochoa265711 ай бұрын
Pero que estas explicando ahí absolutamente nada. No has dicho porque estas haciendo lo que estas haciendo pesimo video
Пікірлер: 25
Awesome vid thx Canada Anyone who complains does not appreciate content creators/helpers do this out of kindness...
I CANT THANK YOU ENOUGH MY MAN!!! No talking, clear visuals, helpful written reminders. Just perfect man, subbed
Oh man, i don’t know what i would do without your video i was able to do the same thing just by watching your video You are amazing 🙏
@48hourpumprepair96
4 жыл бұрын
Glad I could help!
You make it look so easy!!!!!!
Great video
Great video thanks 😊
What model # repacking kit did you use?
Thaksss
what type of grease do you use ? and where do you get it at ?
Approximately how tight should the piston valve be? I snugged it and gave it another half turn and it eventually came loose even with thread lock. Another time I tightened it pretty tight but it ripped my packings after a few uses? Help? Thanks!
@48hourpumprepair96
2 ай бұрын
You have to be careful, its a fine balance. I tighten just enough that the packing are not swelling out, and always use thread lock. And when you put the rod in the cylinder make sure you use LOTS of grease, it will help prevent the packings from getting sheared.
hello I have a 390 greco but when I turn it on it burns the fuse that fails it could have
@48hourpumprepair96
3 жыл бұрын
Could be a bad board or motor.
hard to follow did you put tread locker or ??
@48hourpumprepair96
3 жыл бұрын
Thread lock on piston.
What grease did you use?
@48hourpumprepair96
3 жыл бұрын
Red brake grease.
Didn’t show how the seals are supposed to go on the most important part
💦반갑습니다,수고하십니다,항상건겅하시고 복받으시길바랍니다,,,Elastic coating (탄성코트)work on veranda wall..............
What the hell was all that oil in the pump for? I’ve been a painting contractor for years and never have I seen black oil in a airless. Bizarre 😮😂😂😂
@redneckem1
11 ай бұрын
Dirty packing fluid?🤷🏻♂️
no talking or explanation of what's going on, meh....
@ismaelarredondo394
Жыл бұрын
good video .. i did it i fixed the pump of my spraying machine
Pero que estas explicando ahí absolutamente nada. No has dicho porque estas haciendo lo que estas haciendo pesimo video