Thanks for the great detailed explanation. Top KZread channel 👌 ❤

love all the info you share with us sir. we appreciate you

Awesome video Master Ernest 👏 I love it ❤️

Great camera work and explanation on airflow...

Gracias por el vídeo muy instructivo

Thanks for the video on the 1st Reg.. I was looking for those O-ring sizes!! This reg doesn't have an exploded view in Fx's pdf Keep these videos coming!!!

I think a great follow up video, would be on the regulator behind the trigger! Always appreciate your informative videos thank you..

@ernestrowe5061

Жыл бұрын

Hi, its the same reg but its in a awkward location

@12VALVETORQUE

Жыл бұрын

Thanks, I did not know that.

Hello Ernest… mine has only 11 washers… I only have 130 bars. Can you please help with that.

Hello Ernest, thanks for your videos, they are very good. I am new user in FX, but old in pcp guns. Recently I bought an M3 .25 700mm barrel. The first regulator is 150 bars, when I shoot, this regulator get down about 30 bars, then the pressure quickly return to 150 bars but after 2 hours from the last shoot the first regulator is 170 bars and keeps that pressure. Do you know what could be wrong?

Thanks for your video, I have an m3 impact, air comes out of me The cannon..What do I have to do?

Will you do tuning a power block for heave slugs with 700mm barrel Wayne tec from South Wales

Hello sir, I ve watched your videos time and time again. Much appreciated information, very detailed like no other. A question pls : Will this M3 bottle connector also fit Crown MK2 ? Looking for a way to make optimal use of my 300bar bottle i ve mounted on the Crown. Thank you. Lester

Buenas noches quería saber si podría ayudarme tengo fx m3 que tiene un inconveniente que el seilever no se queda trabado para que pueda poner el cargador o poder disparar el rifle si me podría ayudar se lo agradecería

Nice video Sr I have a cuestión how many washers came from factory in the regulator because I opened my regulator and only came 11 washers

Ernst a person poster that when taking the 1st reg out they are so tight it damages the weapon before it breaks loose. Whats your experience with this.

@ernestrowe5061

Жыл бұрын

We use a thin delrin washer to prevent scratches on the action 😊

I have an issue with a slow air leak I have discovered that is coming the adjuster screw in the first reg I have replaced the o ring on the screw and the piston but it is still leaking air what could it be?

It looks likes it's easier to work on then the MII regulator.

I love you

Awesome video Ernest I use 14 washer for a 200 bar and it's perfect (())(())(())(( bottle

Hi Ernest. What size o ring is on the inside of the reg body? The hidden one. And what exactly does adding washers do?

@ernestrowe5061

Жыл бұрын

Hi, 1st or 2nd reg?? If the reg can’t go above a certain high pressure one washer will boost the limit above 50b. Per example second reg 175 first rag 210b. Will make spring stronger so requires more reg pressure to shut the supply. Only required using high regulator pressure. For example us only 80% of the reg pressures capacity not 100%. Inside 2nd Reg body is 4x1.5mm oring

@orensalomon5534

Жыл бұрын

1 reg

@orensalomon5534

Жыл бұрын

O ring inside first reg. Fx has no schematic on it and I would like to change out all o rings in reg.

Hi Plz wanna know size exactly of o ring of 1st regulator and where can i buy just the 2 oring

Hi Ernest ive got problems with my dowti seal how can i fix it or if anyboby can help telling me ig you have problems with tat ahd how did you repair it ??? pleas help im in mexico exactly in torreon coahuila thanks and my best regards

Nice one! My first reg is showing bottle pressure so not working thought it might be the gauge so replaced it no difference I guess it must be one of those seals? Thanks Adrian

@mammadbashirov7914

Жыл бұрын

Me too

@ernestrowe5061

Жыл бұрын

Replace the 8x1.5 nbr 90 top of brass bushing

@mammadbashirov7914

Жыл бұрын

@@ernestrowe5061 8×1.5 nbr isn't mentioned in M3 tech. list. Only 9x1.5 nbr oring mentioned.

@ernestrowe5061

Жыл бұрын

@@mammadbashirov7914 yes, typo error it is 9 x 1.5 👊

@mammadbashirov7914

Жыл бұрын

@@ernestrowe5061 9×1.5 NBR 90 or NBR 70?

Can the reg pressure screw be turned either way to achieve pressure wanted without and problem

@ernestrowe5061

Жыл бұрын

Hi, no issues unscrewing to raise pressure, the reg doesn’t have auto bleed in lowering pressure -> u have to degass and set pressure

Can you tell me about size oring in firs regulator m3

I guess the the 13th washer would be facing up,,right??

Hi Ernest i have that, exactly leak in my fx m3 i all ready , change all the o-rings in the regulator all of them and the leak still there, yeas it less, but it´s all ready leaking can you pleas help me what eles do i have to do ???? PLEAS HELP !!!!!!

I wish I could afford fir you to fix my fx impact m3 22 cal 800mm sniper it just went from awesome to crap 😕 😢

Hello sir where can i buy a regulator 1 ? My original regulator is broken Thank you 🙏

What are the possible reasons for M3 reg slow refill? It takes almost 8 to nine seconds

@ernestrowe5061

Жыл бұрын

Try, checking the reg adjustments screw and the piston could be partially clogged. Use a small wire to clear the passageway. Or the bottle reg gauge tightened too much that is partially blocking the gauge or a faulty gauge,

@IbrahimKhan-nc2hx

Жыл бұрын

1st reg is doing fine, Im not happy with the second reg

@ernestrowe5061

Жыл бұрын

@@IbrahimKhan-nc2hx, check also for clogging rag adjustment screw and the piston. Also, try 15b or so higher reg pressure to increase refresh rate

@gunzzz7826

Жыл бұрын

ВОзможно у тебя давление первого редуктора слишком близкое к значению второго редуктор. Разница должна быть около 50 бар, иначе будет медленное заполнение.

I turn my adjuster more than 2 turns and still i got 150bars less, whats the reason? my 4X1.5 oring blow out and air leak

@ernestrowe5061

Жыл бұрын

Hi, if no raise in pressure while adjusting, the stack is max out -> you need a stronger spring stack, add one more washer ()()()()() or ()()()()())

@Erealiza

Жыл бұрын

@@ernestrowe5061 thanks... ill try it tomorrow

@Erealiza

Жыл бұрын

@@ernestrowe5061 I stack my spring ()()()()()() and turn the adjuster 2X but still my pressure is 83bar.. Im afraid if i turn it more than 2X my 4X1.5 oring will burst again.. I have no stock on the washer to make it 13..

@ernestrowe5061

Жыл бұрын

@@Erealiza --> confirm reg pressure by replacing the reg gauge

@ernestrowe5061

Жыл бұрын

@@Erealiza replace gauge to confirm actual rig pressure

Always very informative mate, and very helpful... Cheers, Mark, KZread Channel: Farm Pest Management-Airgun

My m3 has horrible 1st reg creep (30bar), has since new.

@ernestrowe5061

Жыл бұрын

Hi, I would change the gauge and see if you get the same 30b creep easier then taking the reg apart not knowing which seals is leaking.

@2002ZRX1200R

Жыл бұрын

@@ernestrowe5061 It never climbs above 30bar of creep, and it doesn't change when adjusting reg pressure. It was causing issues with consistency for sure. Having trouble with all 3 of my last fx purchases with consistency, but only the m3 with issues from creep.

@2002ZRX1200R

Жыл бұрын

@@deeparker6109 mine required the opposite to reduce creep. I've upped my 1st to 190 and the creep has reduced to 15bar. 2nd at 150 and consistency is now better and running lower hammer spring tension it's grouping pellets better and I can swap from .22 compact to 9mm, all that's required is an adjustment of the power wheel. From 6 to maxed. .22 @ 883 average to 9mm hybrids @ 967 average.

hello! How can I get the first regulator to recover something faster? I have it at 150 bar and 2nd at 120 bar cal 25. Sometimes the first regulator recovers a little slow, which practically equals the 2nd and causes a low shot in fps, I have observed in your videos that it recovers quite quickly, what can I do, thanks!

Hello, could I ask you for the exact dimensions and Shore rating of all five o-rings? I can't seem to find this information anywhere. I would be very grateful. Thanks in advance!!

@ernestrowe5061

Жыл бұрын

Here u go: fxairguns.com/wp-content/uploads/2021/04/F10370-Impact-M3-1.pdf Maverick fxairguns.com/wp-content/uploads/2022/01/Maverick-1.pdf

@tomaszturzynski6881

Жыл бұрын

@@ernestrowe5061 Thanks but I mean the other one. Part D parts 96, 97, 98. O-rings inside part 97 are not specified.

@ernestrowe5061

Жыл бұрын

@@tomaszturzynski6881 all those oring has shore #. What gun we talking about? M3?

@tomaszturzynski6881

Жыл бұрын

@@ernestrowe5061 M3. If you look closely the internal structure of part 97 is not shown on the documentation. In your video you specify the sizing of some of the o-rings but nor all and not their shore #.

@ernestrowe5061

Жыл бұрын

@@tomaszturzynski6881 i see, FX is working on that. The 2x1 are NBR 90 the rest are 70

I'm sorry friend, but you didn't do anything if it doesn't show how your idea works, there is a person who has a channel I think called AirgunLR he explains and shows how it works after his idea

@ernestrowe5061

Жыл бұрын

Everybody has there own point of view, i will explain in the upcoming tuning videos-> Cheers. And please don’t advertise other members channel here, please

@philippelabelle9988

Жыл бұрын

Very much appreciate!

We know everything is about the impact…fx can’t even get the parts to the deals…without a month or more waiting time…such a joke…

@ernestrowe5061

Жыл бұрын

Sorry, Dealers don’t get part’s unless they order the parts.

Hello Mr. Oring what size is the regulator set ? thank you very much Greetings from Jakarta 🙏🏻🙏🏻