#Frankingston
Автокөліктер мен көлік құралдары
In this video we worked on cutting out and replacing the front floor pans and all of the inner rockers and bracing connected to it. The #FRANKINGSTON build is moving quickly. Stay tuned for part 5 we should have the quarter panels on.
Пікірлер: 28
You got her done❤
Really enjoyed your videos sir I'm hoping to work on my 60 Belair this helped a lot watching what you have done thank you for posting best regards Richard
@bpbrestorations2093
2 жыл бұрын
Thanks Richard
I just subscribed
Appreciate your video, very helpful on my 64 belair. Doesnt seem like you had alot to work with. Nice job
@bpbrestorations2093
2 жыл бұрын
Not much lol
The inner rocker where the braces get welded to is that a piece you have to make yourself or can you purchase that
@bpbrestorations2093
2 жыл бұрын
Make it yourself
Thanks for the video. I'm doing a 63 Biscayne. This video helped me with the pan issues. A problem I have is the front of the inner rocker is mostly rusted away. I have the dish shaped support then 2 layers. I can't tell how they were originally. Did you have these on your 64? Thanks Robert
@bpbrestorations2093
3 жыл бұрын
I cant think what it is exactly you are referring to. If you got a pic email me at cbuckner0859@gmail.com . We did replace inner rockers on this one and I'm sure it's the same.
@Cheez1979
2 жыл бұрын
You’ll have to make them yourself.. I made mine out of 22 gauge .. I was calling them the “boomerang “in this video 3:18 is the profile from underneath.
@josecollazos6
2 жыл бұрын
@@bpbrestorations2093 where did you buy the pans at ?
What gauge steel are you using for patching?
@bpbrestorations2093
3 жыл бұрын
18 gauge. Its closest to factory and most readily available. It's just a little thicker than factory but gives you a little more to work with when welding.
I'm building a 63 impala and needing to replace some sheet metal. Where do u buy it from?
@Cheez1979
2 жыл бұрын
Classic industries
@bpbrestorations2093
2 жыл бұрын
Classic industries, raybuck, rockauto, ebay, sometimes even amazon
Great video! Stumbled across your channel and just subscribed. Will be heading back now to check out some of your other videos. I got a Christine project underway on my channel. If you get a chance check it out. Keep up the great work. 👍
@bpbrestorations2093
Жыл бұрын
Thank you! And I'll check you out
I hope you get more views for every time I re-watch your videos. I'm looking at the 5:51 frame where you had tacked the passenger floor pan. I looks like you had about a 2 inch overlap of the new pan and the old one. Then tacked on top and bottom. Is this correct. Thanks again.
@bpbrestorations2093
2 жыл бұрын
As long as your plugs are good and your welds are solid, no issues. I put as many spots and plugs as I can and always solid weld everything possible once it is in.
@rsonweb2060
2 жыл бұрын
@@bpbrestorations2093 Thanks!
How much does something like this cost
@bpbrestorations2093
3 жыл бұрын
Full resto? Or just floor pans and inner rockers?
@southside6155
3 жыл бұрын
@@bpbrestorations2093 just floor pans and inner rockers
@bpbrestorations2093
3 жыл бұрын
Roughly 3k
@Cheez1979
2 жыл бұрын
Not bad as far as price considering the pan runs about $1,100 and consumables are about $500
Why was the steering wheel on the right side in the beginning of video,? Weird