Ford Everest Intake Manifold & EGR Removal DIY | Ranger | T6 | T7 | TDCi | 2.2 | 3.2
Автокөліктер мен көлік құралдары
Step by step DIY guide on removing Ford Everest/Ranger Throttle body, Intake Manifold, and EGR. Comment below for any questions and I'll try to answer whenever I'm free. Hope you like this video and don't forget to subscribe! Thanks! :)
Follow us on Instagram: / btdgarage
Пікірлер: 116
THANK YOU SO MUCH. Was doing glow plugs and took the egr motor off to remove the manifold easier but some jerkoff messed with the position of the lobe while it was off and i couldnt get it back on. Here i could see the exact position and it went right in. 5 stars 🤘
@btdgarage
2 жыл бұрын
That’s great! Thank you :)
Thank you BTD Garage for sharing this video. 👍🏽
Verygood video! But when it said its time to remove the intake manifold and used a pair of wrenches to remove a rear bolt, I changed my mind to calling my mechanic let him watch this and just buy him some beer😅
Thank you bud never done one on a ranger made my life so much easier 👍.
@btdgarage
Жыл бұрын
Thanks! :)
Well done! Greetings from Germany
Wow amazing job!
sir may quotation ba kayo rebuild ng 1st gen fortuner 2.7 vvti, both its AT transmission & engine
Hi took the ranger 2012 2.2 diesol to mechanic to replace glow plugs,plugs came out easy and put the motor back together i drove it for couple of hours and engine light came on ,code was p042f egr valve closed ,called the mechanic he wasnt much help stated could delete the egr all together . any suggestions would be appreciated .also great video.
Great video..but how many km did this vehicle have?
Thanks for the idea sir. It is helpful. I can do it on my own. DIY . Next video . Turbo cleaning please 😅 thank you
Thank you so much for this video!!!
Very good video, thanks! Could you please do a video on removing the EGR cooler as well please?
@btdgarage
2 жыл бұрын
Thanks! I’ll try to :)
I have a 2016 Ranger. The engine management light came on firstly a bout 6 months ago but the mechanic cancelled it out as he said it was possibly a sticking EGR valve. I an see from your video that it was a buggar of a job and an easy fix just to cancel out the codes. Months later (2 days ago) the same happened again. (He cancelled out the code). What do you suggest? 120 000km on the clock. I use Premium diesel and service the Ranger every 6 months. Should i have the EGR valve serviced or replaced? Can i use a Diesel intake cleaner to help free up the sticking valve?
Can you do a video on EGR cooler removal and coolant line bypass.
do you have anything on a 2012 Ford Ranger T6 2.2L diesel?
Is this the same for a 2.2 L diesel ford ranger hi-rider 2013 model??... Roughly how long is this take to replace egr vavle and clean manifold??.. best video I've seen so far awesome work
needed this before i started on mine
Great sequence, good vdo
been watching for the this video on how to remove the egr valve. I 've done mine at 60K+ odo but unfortunately wasn't able to remove the egr valve because of that one(1) nut that i could not access considering the space constraint. hopefully i could remove it, diy next time..:).. thanks for the video sharing sir. God bless
@btdgarage
2 жыл бұрын
Thanks! :)
Nice!
Well here I thought I can do it on a Saturday morning by my self...... So that idea went out of the window at about 3 min in the video. Thanks for the heads up. I will be taking my Ranger to a professional to do the cleaning.
@terminatortre24
Жыл бұрын
Please dont, mechanics dont want to work on cars because of Fords. Just throw in in the bin and buy a new car
@veneratedmortal4369
7 күн бұрын
It actually seems not too bad. on my old Prado, I have to take the injectors and the intercooler off as well.
How many kms had this done?
Magkanu po kaya ang labor kapag magpalinis ng EGR at intake
Are you from the Philippines? If you are. How much for cleaning my ford everest 2017 trend?
hola, saque el motor o actuador (8:06) de la valvula egr la volvi a armar y hace un ruido cuando la apago, sabes porque hace ese ruido o es normal? saludos desde Argentina 🇦🇷
How to disconnect egr connector?
Priceless video, thank you so much for sharing your knowledge.
@btdgarage
Жыл бұрын
Thank you!
@masuzyokumwenda9730
Жыл бұрын
Thanks
Thank you so much for the video. I sure couldn´t do it without this video. Any advice on how to get stuck glow plugs out?
@terminatortre24
Жыл бұрын
Set the car on fire, its just a Ford. Get the insurance money and buy something proper
@AustinPetDetective
5 ай бұрын
Intelligence of an ant.@@terminatortre24
How many klms did this car have on it?
Hi sir do you have any egr cleaning video on 2.0 engine?
@btdgarage
2 жыл бұрын
Sorry we don't have one yet. We'll try to make one as soon as we get a chance :)
Sobrang galing ng pagkakagawa ng video detalye. Salamat sir sana madami pa sa ford ranger. More power para more video.
@btdgarage
2 жыл бұрын
Thank you po
Do I need to replace intake manifold gasket set at the same time as this or are they made for long lasting usw
@veneratedmortal4369
7 күн бұрын
Check it with your fingernail. if it's hard like plastic yes, soft o ring you are fine.
Great job, I would have burnt it by now
Where po located ang shop ? Thanks
Good pm boss.i need your help. Ford everest 2011 Diesel.. Issue.ignition on the engine light and glow plug light not showing and cranking but engine not starting.pcm connector no power supply.where is the location of PCM RELAY? THANKS
@gutadin5
2 жыл бұрын
How many mileage now?
Do we need to prime it after the fuel filter is changed?
@btdgarage
2 жыл бұрын
Yes
Hello.. my everest 2016 engine is shiver when it idle and the ac is on.. Can you help me sir?
in how many kms this manifold cleaning required? i own a ranger t6 3.2
@btdgarage
3 жыл бұрын
We recommend it every 60Tkms
Great Job! To replace the 5 glow plugs on a Ranger 3.2 i have to follow this steps too, right?
@btdgarage
2 жыл бұрын
Yes bro.
@lastpaceended5866
2 жыл бұрын
Also trying to find a video showing how to replace the glow plugs on a 2012 3.2 ranger. Do you have to remove the EGR to get to the glow plugs or is moving the Manifold enough to access the glow plugs? Loving your videos Thanks
@btdgarage
2 жыл бұрын
@@lastpaceended5866 Yes you can access the plugs once you remove the manifold. Thanks :)
awesome... a bit curious with coolant hose.. do i need to prime it after I put it in place..
@btdgarage
2 жыл бұрын
Hi brother, simply put it back in place and top up the coolant reservoir upon starting the vehicle. Make sure to let the coolant system “bleed” for a while or to let the air bubbles escape while idling. Drive the vehicle around for 10-15mins then recheck the coolant level and top-up if necessary.
@franciscoandres9053
2 жыл бұрын
@@btdgarage Thank you for this video, I learned a lot.. hope more videos to come.. thanks again for sharing...
@btdgarage
2 жыл бұрын
@@franciscoandres9053 Thanks!
do you need to relearn the idle after the cleaning?
@rogeliojr.villanueva4860
7 ай бұрын
Yes. Everytime you need MAP and MAF
Ngtanggal ng bateri pgllinisin egr kailanga n ireset ng scanner bgo start a engine
sir.may EGR na po ba ang everest 2005 model?
@btdgarage
2 жыл бұрын
Yes
Do u recommend egr delete for longer life of the engine?
@arielatom03
2 жыл бұрын
You will get a check engine light
@theowenssailingdiary5239
Жыл бұрын
@@arielatom03 I didn't..
Now cleaning my inlet manifold etc, carbon buildup was 8-10mm thick 🤦♂️
@marcusbarnes5929
2 жыл бұрын
Did you have a catch can?
Sir san po loc nyo, low power po kc everest ng bos q pagawa ko sa inyo 2017 model 3.2
@btdgarage
2 жыл бұрын
Waze: BTD Garage in Q.C. po thanks
I have a 2019 3.2 ranger with 18000 miles on the clock & I've seen a lot of KZreads about egr & coolers failing do I need to be concerned??
@btdgarage
Жыл бұрын
Not really. Just have your EGR cleaned every 40k miles. 1st sign of egr cooler failure (internal coolant leak) would be white smoke on startup. But this usually happens on a few high mileage units. We’ve had 3.2 rangers in our shop with 200k+ miles on them but still have perfectly working egr/cooler. If ever this happens to you, either replace the cooler or just bypass the coolant hoses to the cooler and blank the egr on the exhaust end - you’ll need a tuner who can also disable the EGR on the ecu for this.
@tombradley4842
Жыл бұрын
@@btdgarage thank for the information much appreciated.
@teeanahera8949
Жыл бұрын
@@tombradley4842 ebay has plug and play kits to fool the computer into thinking the EGR is not required.
What model is this everest? Is this the one with 3.2 liter engine?
@btdgarage
3 жыл бұрын
This one is 2.2
@gutadin5
2 жыл бұрын
@@btdgarage is this Everest Trend?
@btdgarage
2 жыл бұрын
@@gutadin5 Yes
@gutadin5
2 жыл бұрын
@@btdgarage if i buy a 2021 Everest trend now, do you you know how many years or thousand kms before issues will come out? after 4 years or 45,000 kms?
Saan nyo po nabili ang mga special tools na ginamit niyo po? Nahirapan kasi akong maghanap ng star screw driver eh na 12mm. Salamat po
@irvinnolasco8160
Жыл бұрын
I meant yung tool po na pang remove sa torx screws, where did you purchase it po?
@btdgarage
Жыл бұрын
Online Sir madami. Try Lazada or Shopee. Get the branded ones po para durable.
@irvinnolasco8160
Жыл бұрын
Anong specs po ng torx key nyo po? May nakita kasi ako sa Shopee Ingco torx key na T50 ang size. Ok lang po ba yun na size?
Sir. Ano po recommended cleaning solution mo para sa lahat ng parts na lilinisan? Planning to clean mine 80k kms na. Thanks
@btdgarage
2 жыл бұрын
Hi, you can use engine degreaser on the manifold & egr valve then rinse with a power washer. Just make sure to remove the sensor on the manifold and the egr motor. Use an electronic parts cleaner or Maf sensor cleaner on the throttle body.
@angelonocedo5564
2 жыл бұрын
Thanks sir
@gutadin5
Жыл бұрын
@@btdgarage totoo ba na sirain daw ang ford?
Sir ask ko lng sana. Ranger po kasi unit ko 2.2 dn. Same parts dn po b lhat to? Balak ko dn po sna diy maglinis. Sna mkagot nio sir. Salamat po
@btdgarage
Жыл бұрын
Yes po
@gLeM187
Жыл бұрын
Thank u po!
Mgkno palinis
location at magkano
Japanese Suv like Mitsubishi is easy to remove Egr. This one is troublesome.
Great video, but way too much trouble for this guy. At least now I know I wont be doing it. Ha Ha. Thank you.
Bloody hell !
I'm doing this at the moment, and I'm hating life. This motor is seriously the worst one I've ever worked on.
@btdgarage
2 жыл бұрын
I feel you bro :)
@markconnell6268
Жыл бұрын
Try installing a diverter valve on a 320i f30 bmw
@garycarlbalictan3440
Жыл бұрын
At first brother its sucks, but after your 2nd and third, youll be able to close your eyes while doing
@turbostyler
Жыл бұрын
@@garycarlbalictan3440 yeah after doing it and looking back it's not that terrible. But I still don't want to go back there...
@tineshganesan2369
2 күн бұрын
No cap bro, just got the oil pan replaced and it was way more dismantling to do than other motors
Too complicated. I hate Ford, a simple job they make it complicated.
@gutadin5
2 жыл бұрын
Why you hate ford?
@bethzarin6439
2 жыл бұрын
@@gutadin5Are you not reading my explanation? I said a simple job they make it complicated. Are you not reading my explanation? I said a simple job they make it complicated. Are you not reading my explanation? I said a simple job they make it complicated. Are you not reading my explanation? I said a simple job they make it complicated.
@gutadin5
2 жыл бұрын
@@bethzarin6439 repent of your sins and accept Jesus into your heart as Lord and Saviour and you will be saved John 3:16 Jesus the only way to heaven John 14:6 Give your life to Jesus Ask Jesus for your salvation.
@bethzarin6439
2 жыл бұрын
@@gutadin5 repent of your sins and accept Jesus into your heart as Lord and Saviour and you will be saved John 3:16 Jesus the only way to heaven John 14:6 Give your life to Jesus Ask Jesus for your salvation.
@gutadin5
2 жыл бұрын
@@bethzarin6439 you too, i already gave my life to Jesus.
Ffs use an oil fumes catch can. When will people learn.