I been dreading to do my door because of the fiberglass but after seeing you go this route, I'm gonna give this here a try

@ParkerTheBasshead

3 жыл бұрын

Yeah I was in the same boat man

@robsorgdrager8477

3 жыл бұрын

Just remember, you can lay out carbon fiber the same way you do fiber glass. The only reason you need to vacuum carbon is if you are making a structural part for impact strength of for a wing so it will flex and be strong. Rolling carbon is still strong but really light and it's better at sound dampening. Heck I've used old fleece blankets and that really cuts down on the itch. With fiberglass just remember, the colder the shower the better it removes the itch... Used to work for LUND industry and really cold water takes the slivers out.

@wtfngarage2082

3 жыл бұрын

Same man let git some doors made lol

I excited too Parker. Nice job on those door cards brother.

Nice video! I did a similar thing with 8 8’s in the 2 front doors of my f150, once difference is that I made a trim panel that a removable baffle mounted to. Then made a quick disconnect wiring harness that plugged into a distribution block on the back of the baffle. Can strip the door in less than a minute. I also ended up doing a little body filler over top the foam that I used to smooth out and spray with a gloss black to match the rest of the interior 👍🏼

Love the budget builds!!

Great tip on tightening the door clips up at the end…thanks! 👍

crazy I literally was just talking about doing my doors in a similar way because I didn't want to fool with glassing them and now you made a video

I was drinking my coffee yesterday watching this video, now I want to add 2 more tweeters to each door, thanks.

Nice work, Parker. You did a good job.

Wow I’m glad to see how much your channel has grown I love all your videos man keep up the good work

@ParkerTheBasshead

3 жыл бұрын

I appreciate you!!

Nice work, bro. Definitely gives me confidence to do the same. Thanks for the vid👊🏾👊🏾👍🏾

I've been waiting for something like this! :)

This is a great setup fam, I will be following this step by step process to upgrade the mids & highs on my 98 marquis 👍👍

Great Video Parker, those panels look great with those DS18's that Sequoia going to be a banger!

@ParkerTheBasshead

3 жыл бұрын

Thanks man I can’t wait to get everything done

That is clean! Probobly gonna do this to my Xj once I get around to starting that build

This is my second or third time watching this video and I love it I’m slowly gaining the confidence to do my own Thanks for the content

Amazing door panels bro 👌 I am inspired 🙂 2 do mine thinking bout doing 4-8" sundown mids & 4- tweets in my 2010 Tahoe

Looks clean bro! Great video as always 👍👊

Holy cow, thanks for this. I’m definitely going to chop up my 96 accord now. I’ve been missing mid bass for years. Thanks for the non fiberglass solution. And cheers to a fellow dub dnb fan. Just got back from secret dreams

Love sky high audio stuff. Their wire is sick!!

Great video Parker! Nice job on the doors. They came out awesome. Can't wait to see how the build comes out for this year. I just saw the Blackbrick Brickhouse subs. I'd love to see you run 6 of those Brickhouse in the back of the Sequoia. Its gonna take a bigger amp though! Personally, I would love to see you rock 2 of the white Wolfram 9k amps strapped together at like 1.66 ohms or whatever it comes out to be with 6 subs.

Thanks for making this video parker.. I need to build custom door pods for my new system.. was trying to find ways to do it without fiberglass.. awesome video.. keep up great work

Great job. Thanks for showing us how to. Im going to try this on my yukon. I'm excited 👊

You make it look so simple !

Sweet job BROTHER!!!

Great work bro thats all the motivation I needed

Does look nice bro. In case anyone doing this wants or needs extra room you can easily integrate the wood to the inside of the panel!

Congrats, excellent video bro!

That looks great. Nice job

Awesome video. Nice work 👍🏼

Nice I have some of those I'm ordering Like how you did it yourself. Gave me an ideal on how I'll do mines. Thanks for the video

That is really nice!! Diggin it!! Been wondering how I'm going to do my doors in my truck!

every time you upload its a great day

@ParkerTheBasshead

3 жыл бұрын

Really good to hear!!

Another banger video yet again he didn't let us down

@ParkerTheBasshead

3 жыл бұрын

Good to hear!!

Great video....I am currently in process of figuring out what I want to do for my 09 Tahoe. I'm a total noob to car audio, but I'm learning as I go. I want loud music in my truck so I'm researching my way to next level haha.

Get loud 🔊Love the vids man I'll be doing something like this in your video here soon just Had the twin's on Friday so plans on my car audio when we get home 🤙🏼

Dude…that looks badass. Your doors are going to scream.

Another great video.

You got me thinking now this looks so easy to do man lol

Beautiful job my friend

@jeldred80

3 жыл бұрын

I still really want to help you with something!

Nicely done

You taught me something and you inspired me

dude awesome video everything is looking awesome

@ParkerTheBasshead

3 жыл бұрын

Thanks really means a lot!!

They came out pretty clean brotha nice job 4” coil huh that’s gunna be fun

Great outcome man!!! But now I’m interested in that Subaru too lol

Nice job 👍

Wow looks great man :)

Great video now I’m ready to mine needed some motivation thanks man

@ParkerTheBasshead

3 жыл бұрын

Good to hear!!

@Peaterbeaterchickeneater

3 жыл бұрын

I know you said you did this the way you do because of time all I’m gonna do fiberglass on top of all the other steps this is way better then the speaker rings snd hot glue and sticks that I see everyone else do

Nice video Parker gonna do the same thing to my truck

This is so awesome good job bro💪💪

Damn this what I want to do to my blazer...Nice work

Loving da content bro 💪🏿💪🏿💪🏿💪🏿💪🏿

Nice job.

Nice job parker

Great video!!!

Good idea!

Nice job guy!

@pinkwiener23

3 жыл бұрын

If the crossovers rattle still try some hot glue... easy to take off if need be

Good job👍

nice work

My fist video and I just subscribed good shit brother! 💯

@ParkerTheBasshead

3 жыл бұрын

Thank you means a lot!!

@isaflo713

3 жыл бұрын

I was wondering how I was going to do my doors thanks bro thanks so much! I've watched so many videos but none as detailed as your content. Keep pushing that fire bro!

Amazing work. Luv the layout.

@ParkerTheBasshead

3 жыл бұрын

Thank you so much!!!

You can put all the speakers you want in your door but nothing compares to a set of Q-Form kick panels with some speakers like Boston Acoustic Pro 60's pushed with a JL Audio 300/2 supplemented with some more high-quality components like JL Audio C-2 or C-3 followed up with some coaxials for the rear doors pushed with a JL Audio 300/4 then build a center console ported box with the port and speaker facing the rear either a 10W6V2 or v3 or a 10W7Ae3 pushed with a 500/1 or 600/1 JL class D amp. With a center console box in a full-sized truck you can leave in the factory mounting system that connects to the truck frame and get no rattling and distortion with of course the proper sound deadening of your vehicle pre install. Looks great buddy! Oh and do not forget to install two matching AGM batteries that match and wire them properly and you will not need capacitors. Full size trucks come with an extra spot for the second battery for the diesel options in their truck lines.

@terryburton971

Жыл бұрын

Jls are over rated i switched a long time ago... Alpine & Pioneer. Z series

@terryburton971

Жыл бұрын

I ran jls the foam surrounds on my w3v2s back in the day dry rotted just junk speakers..... Jl 6x9s couldn't handle the bass lol

Looks good

Great setup! I like the design but I would've spent a little more time on the upholstery. You could've covered the whole bottom with the pleather as the door panel separates into two pieces. Even if you didn't use fiberglass a nice layer of bondoglass would've been a stronger bond.

Cheap & easy 💪🏻 my type of shit! Great vid

Wish my sequoia had nice black paint like yours.

Excellent job. Now let’s say you have 4 sets of component speakers to use on the doors with 8 cross overs. Now since your doing the series & parallel there’s one 4 ohm lead for the mid & one 4 ohm lead for the tweeters so when I hook this up to the cross over is the power rating now still the same? 100-200RMS? How does the series & parallel change how much power I can now use? Does it require mores power because four speakers share the load of one per cross over point?

Looks badass man fr! I need a list of some of you bass songs you use and where to get them lol

👍👍super nice well done about time bro.

@ParkerTheBasshead

3 жыл бұрын

Yeah man been putting it off too long! Glad to finally have them done

I think if you get a nice grayish carpet to match the doors that would be a better option than that black pleather. It would look more stock and the black woofers would stand out better. Maybe you have some leftover after pulling it out of the back?

Thats a sub from me great video man

Tight!!! 👊

That's one.nice hillbilly riggin ! Hell I'm going to try it lol

Great video Bro, Now I'm thinking about replacing all my factory speakers in my 2014 Audi Q7, What do you recommend I love JL Audio Speakers

Nice job

@ParkerTheBasshead

3 жыл бұрын

Thank you!

NICE BRO!!!

@ParkerTheBasshead

3 жыл бұрын

Thanks man!!

Definitely should have just added to the Deaf Bonce speakers, but I completely get wanting to try new things. Hopefully you enjoy the DS18 just as much if not more! Looking good Parker!

looks good I have a Chevy Tahoe I wonder can you do the same thing with the two front door panels

im still fighting these damn manual cranks I messed up and overheated one and broke the crank so now got to remove the whole window and all to fix it

BRUH!!! So dope

I'm curious how those ds18 compared to the soundqubed 6.5"s

Ds18 also makes some speaker enclosure type things that go over the original panels if that something you can do

I'm almost tempted to take some of these very inexpensive drivers and send them to G & R research and see if Danny can do any magic with them

Hey Parker, I was wondering what rms I should run the bb.2s I won at? Ik they are 4ohm which means I could wire them to 1ohm but idk what rms they are for since the website got taken down

Most people use shallow mount subwoofers for projects in small tight spaces.However, I have an idea that's going to use 4 sealed shallow mount and 4 vented shallow mount. With regular size subs I have TONS of options. In the shallow mount world it seems that SKAR is the best. What is the beafyist shallow mount 12??

Hey y'all great video. Wondering if you're going to put new speaker wire to doors and amp and if you'd show how you wired up?

Pleather looks a little rough but fuck it. Looks decent and I'm sure it sounds amazing.

@ParkerTheBasshead

3 жыл бұрын

Yeah I’m not 100% happy with the pleather but it gets the job done for now

@gregfrasier5005

3 жыл бұрын

How do you get the material from pealing off on hot days?

Heat gun would have made the pleather go around the edges without cutting still great job Parker the v2 is turning out awesome

After using this budget series you should try the exl series bro. Been viewing this channel since the first sub review in the Subaru, glad to see you doing bigger things keep up the good work

@ParkerTheBasshead

3 жыл бұрын

Thanks man come a long way!

Hay bro I has a question. I have the taramps 2000x4 the 2 ohms model an I have 2 DS18 8s 8 ohms an 2 DS18 10s 8 ohms as well mid-range..I want to bridge them what is the final impedance output all speaker wired separately from the box going to the amplifier. Can get some advice on that please and thank you sir an congratulations an the win

I’ve been looking at this setup how do you like it and would you still recommend these or something else now that you have heard them???

Nice👍👍👍

Nice

When running these setups with mids and highs. Do you guys run a crossover like component sets have are just let them run..

Is ds18 for spl? I'm putting in a kw DSP and was thinking of morel or hertz. Trying to do both SQ and spl @ the same time. Running two Sundown EV3's with a RF P1000 in a custom ported enclosure

Sweet now that my cars paid I’m going to the same thing , have a few of those same ds18’s waiting for me . I always said I would only do fiberglass because the wood never looks original or clean but yours came out alright it actually looks nice with that many speakers on there. That foam though haha I was wondering how you where going to fill in the gaps

nice

Watching you for a while im having some trouble i hav 4 ds18 6.5 pro classics and 2 8 inch ds18 pro classics and two ds18 1inch drivers i want to run them all parallel to a one channel taramps but im not sure which one to get

Kind of like what I did with mine. Except I just chopped the bottom half of the factory door panel

Awesome job!! Dope!! What music you playing? Nice music choice on your vids.

I have 20 total DS18 speakers in my truck 🤔 They are loud💯