E90 M3 Oxygen Sensor Change in 1 minute [ENG SUB]

Автокөліктер мен көлік құралдары

Watch the full video: • O2 Sensor Replacement ...
Oxygen Sensor Change Fixed Rough Idle & Limp Mode of E90 M3 [ENG SUB]
Malfunction of an oxygen (O2) sensor BEFORE the catalyzer caused BMW E90 M3 rough idle and limp mode. The replacement of the O2 sensors before cat and adaptation reset resolved the problem. A bad O2 sensor before cat stops the engine control unit (DME) from calculating correct air to fuel mixture. The engine will end up in poor combustion, misfire, vibration and eventually limp mode (or limp home mode, BMW’s protection for the engine.) Here I changed the O2 sensors before cat on both banks of the S65B40O V8 engine to ensure the DME gets an accurate signal. After the replacement, adaptation reset of the O2 sensors is necessary. And the replacement successfully fixed the problems mentioned above.
**Codes for O2 sensor before cat. on bank 1(they came randomly)**
2724 DME: Oxygen sensor, signal before cat., bank 1
2726 DME: Oxygen sensor, plausibility before cat., bank 1
2728 DME: Oxygen sensor, coast-mode diagnosis before cat., bank 1
2742 DME: Oxygen sensor heater resistance diagnosis before cat. converter, bank 1
2748 DME: Oxygen sensor before cat., evaluation module in control module, bank 1
277C DME: Oxygen sensor trim control diagnosis, bank 1
**Codes accompanied with limp mode I had**
2B35 DME: Misfire with cutoff, cyl. 1
2B36 DME: Misfire with cutoff, cyl. 2
2B37 DME: Misfire with cutoff, cyl. 3
2B38 DME: Misfire with cutoff, cyl. 4
2B41 DME: Misfire with cutout, several cylinders
2B42 DME: Misfire impairing exhaust emission, cyl. 1
2B43 DME: Misfire impairing exhaust emission, cyl. 2
2B44 DME: Misfire impairing exhaust emission, cyl. 3
2B45 DME: Misfire impairing exhaust emission, cyl. 4
2B4E DME: Misfire impairing exhaust emission, several cylinders
**Parts Required**
Oxygen sensor BEFORE catalyzer X2
BMW 11 78 7 537 984
Bosch LS 17038 / 0 258 017 038
**Tools Required**
8 mm hex socket (trims)
10 mm hex socket (trims)
17 mm hex socket (reinforcement strut/plate bolts)
torque wrench with angle (56 Nm + 90°)
22 mm open hex spanner (O2 sensor)
22 mm open hex torque spanner (25-50Nm)
**Tightening torque spec**
O2 sensor before catalyzer 50 Nm (OE exhaust)
after cat 25 Nm (OE exhaust)
Bolts on reinforcement strut/plat 56 Nm + 90° (replace blots)
Camera: Jing-Ru
Music: Inspired Iguana by Mikey Geiger
Content ID: J45XRFURQPGNUIV6

Пікірлер: 10

  • @littleroller
    @littleroller10 ай бұрын

    Thanks for you replacement guide. What trouble codes did you get to lead you to replace the O2 sensors?

  • @funcarsgoodpeople

    @funcarsgoodpeople

    10 ай бұрын

    Hi @littleroller below are the codes I had and you are welcomed to visit the full video and its description kzread.info/dash/bejne/a6JnlcaeYZq9maw.html ***Codes for O2 sensor before cat. on bank 1(they came randomly)*** 2724 DME: Oxygen sensor, signal before cat., bank 1 2726 DME: Oxygen sensor, plausibility before cat., bank 1 2728 DME: Oxygen sensor, coast-mode diagnosis before cat., bank 1 2742 DME: Oxygen sensor heater resistance diagnosis before cat. converter, bank 1 2748 DME: Oxygen sensor before cat., evaluation module in control module, bank 1 277C DME: Oxygen sensor trim control diagnosis, bank 1 ***Codes accompanied with limp mode I had*** 2B35 DME: Misfire with cutoff, cyl. 1 2B36 DME: Misfire with cutoff, cyl. 2 2B37 DME: Misfire with cutoff, cyl. 3 2B38 DME: Misfire with cutoff, cyl. 4 2B41 DME: Misfire with cutout, several cylinders 2B42 DME: Misfire impairing exhaust emission, cyl. 1 2B43 DME: Misfire impairing exhaust emission, cyl. 2 2B44 DME: Misfire impairing exhaust emission, cyl. 3 2B45 DME: Misfire impairing exhaust emission, cyl. 4 2B4E DME: Misfire impairing exhaust emission, several cylinders

  • @foam_on_face5091
    @foam_on_face5091 Жыл бұрын

    I thought you could replace it in 1 min 🤣

  • @funcarsgoodpeople

    @funcarsgoodpeople

    Жыл бұрын

    😆 Hi Foam sorry for the confusion but I hope this shorts can be a quick reminder of the workflow 🤗 Happy lunar new year hear from Taiwan!

  • @harrazqayyim6479

    @harrazqayyim6479

    Жыл бұрын

    Boss no ctact

  • @funcarsgoodpeople

    @funcarsgoodpeople

    Жыл бұрын

    Hi Harraz do you mean contact? You can send emails to funcarsgoodpeople@gmail.com 🤗

  • @user-xl5iy1zl1m
    @user-xl5iy1zl1m11 ай бұрын

    Can a bad cat cause fuel cut off codes???i got a 330ci 01 manual... I done replaced sparks, coils, cam shaft sensors, the two o2 sensors on top of the exhaust, fuel injectors, MAF sensor, ignition coils and ignition coil harness wiring upper and lower intake boot, I THINK I fixed all the vacuum hoses they were all busted and torn and not connected, even replaced the fuel pump, crankshaft sensor... Cleaned the icv... Cleaned the throttle body.. idk what to do it's misfiring in cylinder 1,2 and 5.. codes are p1341, p1343 and p1351 misfire with fuel cut off.... The engine is lurching... Hard to start up too... I know I have a battery that needs to be replaced it's from 2017... Voltage has been low not sure if that'll cause the issues I'm having... I've replaced more then this as well lol. Radiator and hoses. Clutch. Alot. But anyways yeah help me.... Only thing I haven't replaced yet is the fuel filter... Also when I give my car a full tank to the max the gauge is off by like an inch or so. Or half an inch.. could a bad fuel sending unit cause the codes and issue I'm having as well? Fuel regulator.. ? Anything. Help me. I haven't replaced the post cat sensor yet though I have them just haven't installed them yet...

  • @funcarsgoodpeople

    @funcarsgoodpeople

    11 ай бұрын

    Hi Hope thank you for your comments. I don't think a bad cat would matter. However, you correctly replaced the O2 sensors, the two on the top (before the cat,) so I think there's no faulty parts in the exhaust system. But be sure to reset the adaptation with your diagnostic tool so the engine can run with correct air-fuel mixture. I've checked those three fault codes and they are indeed misfire of multiple cylinders. I suspect not only cyl. 1,2 and 5 are misfiring but also the others are misfiring randomly. I heard that an unhealthy battery can also lead to misfire. So please use a new battery for trouble shooting. Check all wiring connections and grounding points around the engine to ensure the electrical system is intact. I don't think the fuel matters a lot. You can go ahead to replace the fuel filter if you suspect poor quality of the fuel. Just to rule out most of the possible causes. I believe your are very close to the answer! Best luck! Carl

  • @bda808
    @bda8086 ай бұрын

    530d ?

  • @funcarsgoodpeople

    @funcarsgoodpeople

    6 ай бұрын

    Hello I just checked the O2 sensor for E60 520d, there's only one. The other two are temperature sensors. Is this the one you are looking for?

Келесі