Very nice cleaning.. It's amazing.. I love cleaning..

Good job PK Mechanics.. keep safe always guys.. god bless your team.

After watching upwards of a hundred of these "repair" videos, I am amazed that no one has thought that it would be better to clean the dirt and grime off of an assembly BEFORE you disassemble whatever you are working on. No, they take filthy parts and wash them in the same dirty gasoline or diesel fuel that is full of grit and dirt from previous parts. Do they think that they can get all of the grit out of bearings and passages afterward? If this work was done for free for the owner of the machine, he was overcharged. Crude doesn't even begin to describe it.

@raffaellobottoni871

2 жыл бұрын

I do agree with you! Clean before to disassemble all! You shall work better!

@frenchfrysz6695

2 жыл бұрын

I know man, These videos make me cringe. I work with aerospace components and if there was ANY contamination in our assemblies it would be so awful.

@paulb7334

2 жыл бұрын

You couldn't of said it any better I would freak if that was my stuff

@paulocast7054

Жыл бұрын

em que país é esse? Onde é esse lugar?

Never see a working finished bodge, ever seen a torque wrench

Not being a heavy machine repairist, even I laughed. Love there cleaning routine and reusing the damaged extracted needle bearing. Sorry can't watch anymore.

Man that's Pk! A lot of people working as fast as can....very few had knowledge how to do, they just do as seen before!

Good work but please very dirty farish

чтобы заменить крестовину на шрусе,нахера было сбивать подшипник ступицы? да и подшипники крестовины задавливаются без ударов в тисах,им об этом никто не говорил.Да еще приварили их ,потому что стопора не влезли,и при этом сожгли смазку .За такой ремонт к стенке ставить надо!

sounds like minions from cartoon are at work -))

@dusterowner9978

2 жыл бұрын

I think the minions would do a better job

У Паков самые суровые приемщики металлов, если перед сдачей на металлолом, узлы необходимо снять, разобрать и помыть.

super , good mechanics

After working on heavy machinery for many years, I'm speechless, SMH.

I feel bad for the poor sucker that paid to have that done. Anyone watching this please don't hammer the caps into a U-Joint and when the cap doesn't seat it means a needle bearing is in the wrong location and has to come apart again to fix it correctly. Welding the caps on will just make the professional mechanics job that much harder in a couple days when the joint breaks and has to be done all over again the right way. I personally charge more if the customer tried to fix it first just because stuff like this happens all the time and I get stuck dealing with it.

@paulocast7054

Жыл бұрын

onde é esse lugar? Que país é esse?

Amazing

Мне одному кажется что помыл и всё работает 😉

Hmmmm, if i owned that machine and paid for the repair there would be some shallow graves in the woods near by this shop. clutch re-packed DRY and smashing the cups on the universal with a hammer on the dirt (dare say theres a bearing or 3 up in the cup, and lets not talk about who ever gets to deal with the weld......

Зубилом всё похерачили ,зубья подшипники, так ещё и крестовину заварили,верх мастерства,следующий ремонт который не за горами будет,весь узел на помойку

@valdumarchik

2 жыл бұрын

Это точно

в анекдотах покрасить в зеленый и выбросить в траву, а у них помыть и сдать в металл))))

There’s a certain Folly in giving a $10,000 device to be worked on by $.25 an hour workers the outcome can’t be good

So, the idea is to show that your expensive machinery will be all damaged by hammer wielding guys, if you choose to leave these "repairs" to inexperienced contractors without proper tools?

عمل رائع احسنتم

24:52 ммм сальник установлен без замятий и оправок, ммм точность молотка поражает

Why the heck didn't they clean the mud off the housing BEFORE they disassembled it? That star nut has obvious damage from previous hammerings. These sods use a hammer and chisel for everything, and are to damn lazy to spend half an hour making up a special spanner to use on the star nut.

@MaxstallfishDenton

2 жыл бұрын

they don't get paid for it

@JohnnyFlynn76

2 жыл бұрын

at least they showed us how to properly weld U-joints...

@piperdoug428

2 жыл бұрын

@@JohnnyFlynn76 bwahahaha

@glennbrown1961

2 жыл бұрын

Washing bearings in a weak solution of mud, but only after washing all the other grottiest parts in said solution first! Just like it said in the manual! No wonder it's the third world. I understand there is no money for parts etc but for heavens sake look after the parts that are good and don't trash every bloody thing. First thing I said to myself was no...not the bloody wheelbearing with the screwdriver! Not to worry we can fix it with pliers! After 40 years as a fitter I thought I had seen some rough work...and then along comes U-Tube!

@keithammleter3824

2 жыл бұрын

@@glennbrown1961 : And when we damage the uni-joint forks by hammering, and the bearings are likely to come loose as a result, we can fix that by arc welding the bearing circlips in! But what's sad is that the young chap is washing in what is most likely diesel fuel, without gloves. So skin cancer is very likely - and cancer is death sentence in Pakistan.

сделать спецключ это же слишком просто, лучше зубилом гайку закручивать

These guys are not mecanics but destroyers !

the magic pan of dirty solvent and magic rag . 😒😒😂😂

@Stepinup

2 жыл бұрын

It's most probably petrol or kerosene they use to clean parts

👍👍

Hola a todos. Y aparte de eso llevan buenas botas de seguridad. Cualquier pieza que se caiga puede machacarlos un dedo.

I am surprised they even used a new u joint. I expected them to reuse the old ones.

после такого ремонта узел можно выбрасывать.

You will ever see shops like that make even half decent repairs.

well done, every part damaged by a hammer 🤣

@Caninoization

2 жыл бұрын

and every mechanic are short lifespan because touch to many toxic.

@aarondwyer3746

2 жыл бұрын

I have just read 3in a row DK shame,, canonization shame all peaky binders you miserable buggers,decent standard of work

The bearing are shot after prying them off with screwdriver.They are junk.

@stujambo1742

2 жыл бұрын

i would be impressed if that hub lasts a month before it shits itself.......the bashed bearings,washing everything in dirty solvent,the dirt floor.......those stub bearings were cleaner before they washed them!

Brilliant video thank you

@richardtemby4358

2 жыл бұрын

Surely your fucking joking!!

Тихий ужас…

Excelente trabajo los felicito 👏 👍 💪

If you hit it enough times with a hammer and chisel it will be fine.

Comments below point out so many bad practices, but watching people breathe in small droplets of diesel vapor as they spray dry bearings and such with compressed air is so sorrowful. Those poor people will develop lung issues and cancers soon as the human body is not meant to breathe in diesel vapor. I am saying this as I am sure not one person in that shop is wearing a charcoal vapor mask or even an external air supply. Life is cheap in PK land from what I can see. For all those below who say something like "great mechanics" I am hoping you are being sarcastic. This is cheap, bad, and poor practice at its lowest. Likely this repair will fail shortly after being returned to service.

Customer states..it don't nead new bearings

You welded the UJ caps in? WTF

Jawas at it again

Ese eje cardan quedó inservible

Шрус убили, можно в метал выкинуть.

@raminhuseynov9269

2 жыл бұрын

Это просто ахтунг 🤦🏻‍♂️

Same video was posted few days ago in different channel

If they touched my bearings with a chisel he would of seen stars

Şaft önü marsal kırık şaft ufacık milli piriz direği dönüş çapındaki dişli kusunda çeviren annası kırar. Yağı kaçağı ( keçe değişim kaynaklasır) onu arkası bu. Gören birşeyi varmış gibi görüyor. Yağın seviyesi dikkate alındığında sapa sağlam olur oooo makina.

I’ve just realized that their idea of progress is, get a bigger fucking hammer. Just sayin!!!

Я так и не понял , в чем причина поломки была ? Помыть , убить привод и потом выкинуть в чермет ?

есть такое слово писец.

😢😢

That you U-joint job made my ass pucker something terrible. OMG !!!!!!

супер !

🤦‍♂

🤦🏻‍♂️🤦🏻‍♂️🤦🏻‍♂️🤦🏻‍♂️

Pésimo todo!!

@user-es6rr8gm4s

2 жыл бұрын

Полный пиздец👍🙈

Big mistake to wearing ring in your finger , someday you will lose finger

The sad part is that these guys have a life time of medical problems cleaning with solvent and no gloves.

@jeanmarie2683

2 жыл бұрын

même pas un simple pinceau ou au mieux un nettoyeur haute pression , pas de clés a cliquet encore moins de clés dynamométrique , bref du travail de ?????

@terefrio

2 жыл бұрын

is just gasoline

@barboelter

2 жыл бұрын

@@terefrio Still extremely toxic, soaks into the skin then into the blood stream.

That is good work. I like it too much!

@scotabot7826

2 жыл бұрын

Good worK???? Please tell me your kidding!!!!! Tearing up every bearing they hammered on, and that poor U-joint is ruined!!!!!! Bad Bad Bad!!!!

@khimsophacarfixing

2 жыл бұрын

I mean that mechanics are good work.

nice job :)

@earljohnson9952

2 жыл бұрын

50 years behind ,our government would. Have something to say.

👍🇷🇺