Thanks for the video!!!

@AndyFromm

2 жыл бұрын

No problem

@broo_shs

2 жыл бұрын

did you get all info what you asked i hope so.

Love the backhoe. One my favorite years for the 580 Case! Good Video!

@AndyFromm

2 жыл бұрын

Although it has its moments, I really like it. Thanks Dalton 👍

Great video Andy! I have the same backhoe and this video definitely helped!

@AndyFromm

2 жыл бұрын

Thanks, no problem 👍

Great overview Andy.

@AndyFromm

Жыл бұрын

Thanks Larry 👍

Andy great video! You should do one for greaseing the entire machine including underneath the machine! Thanks

@AndyFromm

9 ай бұрын

Thanks, I'll see if I can do one someday.

Thanks

@AndyFromm

Жыл бұрын

No problem 👍

Thanks for the video. How do u check Trans level? While cold not running? While idling warmed up?

@AndyFromm

Жыл бұрын

No problem. I just check it cold, off. Not sure if there is a spec on how but its just a transaxle on here kinda like a 806 farmall or similar tractor. Thanks 👍

@aaronmueller8602

Жыл бұрын

Ok thanks. Reason I'm confused on mine. It's a 1982 580D. Dipstick is the same as yours. Is when I check it cold with eng off, it is wayyyy over full. When I warm it up than check it, it's not even on the dip stick? I do not have a manual or any stickers telling u how to properly check Trans level

@aaronmueller8602

Жыл бұрын

Appreciate your time for the answers. There are not many videos about this stuff 🙂

@AndyFromm

Жыл бұрын

@@aaronmueller8602 I am not for sure but it is possible that is slinging the oil around to different areas of the trans and it appears low. Possibly a case construction dealer could find the correct procedure. Good luck 👍 No problem 👍

Is the rear dipstick fluid level in the transaxle separate from the front eyeglass level.? Are they separate? Do i have to check both?

@AndyFromm

5 ай бұрын

Yes they are separate, I would check each.

Whats the difference between the 580k construction and the super K ?

@AndyFromm

3 ай бұрын

I can't say for sure. Some say sk was turbo but mine is not turbo. I'd say mostly some changes in control layout and possibly a different transmission

How do you drain Hyd, Fluid (to change pump)?

@AndyFromm

Жыл бұрын

On the 580sk, there is a plug on the bottom of the right frame rail. I recorded a video about changing the hose on the pump but haven't got it edited yet 😪

God bless a Motors Where is Turbos.

@AndyFromm

2 жыл бұрын

This one is na, I would love to add a turbo some day. 👍

@broo_shs

2 жыл бұрын

@@AndyFromm 👍

@AndyFromm

2 жыл бұрын

@@broo_shs it needs more power!

@broo_shs

2 жыл бұрын

@@AndyFromm how much you think that needs more power because many ask in machine shops if they would get a good deal and its only need to drill cylinders little bigger and messure all and order new piston and set ring cap to right size, and that will bring little more power and another way its to find right cylinder head to that engine what already have drilled bigger and then just buy right size pistons and ring cap it right size and set it up.

@AndyFromm

2 жыл бұрын

@@broo_shs it is probably around 50 hp right now, you don't have to do all that work on here. as long as it is in good working order, just install a turbo and add some more fuel. I would be happy with 80-100hp. That should be quite doable since my M has the same engine but has a turbo. It make around 100-120hp.