I have just gotten one step closer to being the smartest man on Earth,Thanks for the video

I did this some time ago to 3 batteries and only one came back but the one battery has worked for years and saved me about 130.00 to replace it.🙂

Yes baking soda works. Just did it. My battery died but brought back to life.

@stefandieter7136

Жыл бұрын

Hello it's nice connecting with you, how's it going with you over there?

So many times over the past half century I've sniveled about the desert heat in Tucson, especially the humid monsoon heat but then I remind myself - Hey, at least it isn't Phoenix! Thanks for this video!

@ArrowheadGarage

Жыл бұрын

You understand my pain lol thanks for watching!

Volts is not what you need it is also amps that the battery holds that is important.

Batteries die because the lead plates create a sulfate on the plates. Eventually the sulfates build up to the point that they no longer flow electrons . Cleaning may expose more of the lead and get the flow going again, but usually by this time the lead plates are pretty much used up, so even cleaning the sulfates and putting in new acid will not save it, it may have voltage but very low cranking amps. Another old trick was to overcharge the battery with a high amp charger which would cause the sulfates to flake off the plates, but this was only a temporary solution as well. When you've got no lead, your battery is dead.

@Howdy76

Жыл бұрын

OLD SCHOOL You are correct , sir.

@bobmoser9609

Жыл бұрын

8. THE. DUI GUY IS AGREAT SHOW I thank him for His Expertis in Cases he is incredible and Also THE Police are doing a great job in tuff situations depending on what they not knowing what that next assignment will be ie.minor or tragic but there's a lot to consider in 2 or 3 seconds it is a very tough Profession for Police as I was also a Public Safety Officer God Bless AllHTTPS//WWW.Mass.Gov>orgs> Office :any mail or correspondence for Robert T Moser Should be sent to address of56 St .. Joseph Street Fall river . MA 02723 PObox181is temporarily stopped last 4 1606 because of P.O.errorThank You very much. Sincerely Robert T Moser 56St. JOSEPH STREET Fall river Ma.02723 or call 508617-4622 Thank You very much.HTTPS//WWW.Mass.Gov>orgs> Office :any mail or correspondence for Robert T Moser Should be sent to address of56 St .. Joseph Street Fall river . MA 02723 PObox181is temporarily stopped last 4 1606 because of P.O.errorThank You very much. Sincerely Robert T Moser 56St. JOSEPH STREET Fall river Ma.02723 or call 508617-4622 Thank You very much.HTTPS//WWW.Mass.Gov>orgs> Office :any mail or correspondence for Robert T Moser Should be sent to address of56 St .. Joseph Street Fall river . MA 02723 PObox181is temporarily stopped last 4 1606 because of P.O.errorThank You very much. Sincerely Robert T Moser 56St. JOSEPH STREET Fall river Ma.02723 or call 508617-4622 Thank You very much.HTTPS//WWW.Mass.Gov>orgs> Office :any mail or correspondence for Robert T Moser Should be sent to address of56 St .. Joseph Street Fall river . MA 02723 PObox181is temporarily stopped last 4 1606 because of P.O.errorThank You very much. Sincerely Robert T Moser 56St. JOSEPH STREET Fall river Ma.02723 or call 508617-4622 Thank You very much.The Sopranos

@markrtaylor

Жыл бұрын

kzread.info/dash/bejne/iI2ozdBmfsLWZNY.html

@michaelwarren3853

Жыл бұрын

Batteries are made with two types of oxides. This ia paiste made of sulfuric acud and lead. This paiste is called posive msterial which is then applied to the positive grid after drying to cure it then becomes a positive plate. This is where the battery gets its voktage .the negative plates are formed in much the same way .but chemicaly work differently.the positvive provide the voltage and the negative plates are there to carry the amperage from one plate to the next..

@strattuner

Жыл бұрын

everything has a life and nothing beats new,esp batteries,i dont' know about most people but to me a car truck that won't go state to state, its not worth much,new batteries,new belts,new hoses,every 4 years,no matter what,oil changes every 3500x3 then go to 5000 x3 then back to 3500,keeping the pan clean is all of it,OLD SCHOOL you know nothing beats new or first design,the first anything was designed because the guy needed it,hang in there

without load testing, the battery after doing the recondition 12 v means nothing.

@trevhedges209

Жыл бұрын

That’s what i was thinking, where was the load test, you can surface charge just about any lead acid battery.. load test the fooker to it full CCAs and then show us..

@formosabrowning3539

Жыл бұрын

You are correct

@trevhedges209

Жыл бұрын

@@formosabrowning3539 at my workshop, we managed to charge a four lemons to show 12volts, We were Successful in lighting a tiny LED bulb on a test light for about 40 seconds.. (did I technically recondition the lemon). 😂

@williamcormier257

Жыл бұрын

You are so correct A+for you !!

@BirdwellingtonAmalgamation

15 күн бұрын

Yep. Volts ain't amps. 😂

Back in the early 80's I worked for a used battery service' the owner had a contract with JCPenney's/Sears Kmart to buy all their old batteries' we'd pour all the old acid water out and use a 50/50 mixture of white distilled cleaning vinegar to wash them out then rinse out and repeat' fill with new acid' place them on the charging tables' up to 200/250 batteries at a time' hook them up all together in parallel and charge them on 2 amps for 3 days' then let them sit for a week off charge' about 25% of them would not hold charge' the ones that did' we were selling them for $15.00/$20.00/$25.00 depending on appearance' some would last a couple of months some would last for years. Slow charge is the key after cleaning and new acid.

@pawtaylor

9 күн бұрын

What do you do if you don't have the caps on the battery

@BryanClark-gk6ie

8 күн бұрын

​@@pawtaylor Back then the majority had caps' there were a few that were sealed' on those we had to peel the manufacturer label off the top of the battery and under the label there were caps' they were recessed and sat flush with the top of the battery' on some you could see a small hairline crack between the cap and top of the battery' a small flathead screwdriver or pocket knife and pry them out. On others you could see the outline of the seal' on those we had to take a utility knife and cut into the outline of the seal to separate the cap from the battery and then pry it out. I remember being in the lower shop and all the sudden BAMM!!! Sound like a cannon had went off from the charging process' I could feel the battery acid on my face and arms from being in the air' there was a couple of times they blew a hole clean through the tin roof of the charging area.

Go with spending the money on an Optima battery. I had one in my 2000 Montero for 11 years plus. When I had to scrap the car after my daughter let the coolant go way low and blew out one head gasket. I took the battery out and it is still working perfectly 5 years later! $325.00 Well spent as I probably would have had to change batteries 4 or 5 times during that 16 year period. ONE MAJOR BENEFIT ...gell pack batteries will not outgas or leak and cause rust in your classic Porsche 👌👍

@YoLo-dc1uy

Жыл бұрын

I’ve got a yellow top optima gel battery and it’s still good and strong after 6-7 years now of being used and ran dead on several occasions as well as drained on several Saturday nights over them years in my dirt track car.

@Howdy76

Жыл бұрын

Don't forget to turn then upside down for two weeks a year.

@polarlab113

Жыл бұрын

There are way better batteries than optima

Sure are a lot of experts in the comments section

You made my day , checking voltage with charger attached to it proving you have no clue about electricity 😂🤣😂....

@martinscluff

Жыл бұрын

He said he was showing what the voltage from the charger was. The second time he checked it the negative alligator clamp was disconnected.

Thank you wonderful knowledgeable information about cheap battery second life.

@ArrowheadGarage

Жыл бұрын

Glad it was helpful Paul!

Sounds really good thank you for the good advice

@ArrowheadGarage

Жыл бұрын

No problem 👍

This works, I had a car quest gold last 12 years doing this. In brutal cold to insane hot.

@ArrowheadGarage

Жыл бұрын

Good to hear! Thanks for watching

I've got 50 12 volt battery's that I'm now rebuilding thank, you

thank, you. it works now I've got 50 new rebuilt 12 volt battery's

is it ok to use sulfuric acid to recharge after washing battery with baking soda?

I keep a battery tender on my old truck battery and lawn tractor when sitting for extended periods of time. Works great.

@ArrowheadGarage

Жыл бұрын

That's a good idea!

@EarlLeeBird

10 ай бұрын

Battery tender will constantly charge it, which means that the internals of the battery get warm, distilled water will evaporate, overall liquid levels will drop, acid concentration will be too high and cause corrosion on lead plates inside the battery - this results in a residue that will short circuit one or several of the canisters. Battery tender wont know that there is one faulty canister and will overcharge the other ones to reach the 12 volts. While doing that, it will further overheat the other canisters. The battery will start a car for one time or two and then it has lost its charge to 9v or lower. Also when one of the canister is shorted out or low on liquid, the battery will start boiling when alternator charges it. What the process in this video does is remove mentioned corrosion residue and clean the plates. Then refill with clean acid or salt water. It helps but some of the plate material is still gone and its not comparable to a new battery. Its OK for warm climate areas and petrol cars but not high cranking current demanding diesel cars. Battery tender will work too without any issues but only if you check the liquid levels and top up with distilled water - of course if the caps on the canisters can be removed - on most newer batteries they cant because battery manufacturers use ultrasonic welding to make the covers not removable so that you would have to buy a new battery instead 🤓

For some of the comments who are quick to go to the shop and replace or repair , Please such DIY are for people who find themselves off grid , imagine you are in Alaska or some very rural African place , this can really help. And again some people even if they may be located in big cities they still don’t have money to replace a battery .

@dalehood1846

10 күн бұрын

Well said.

rubber gloves, safety glasses and a good mask thank, you.

Awsome dude, thanks it really works. Try the ark weld method first. Then the cleaning process. Add new Epsom solution afterwards.

Question. How long does a battery last. I had mine since 2018. Do I need a new one. ?

Why not take the old battery to a car shop to do the revival with fresh sulphuric acid? Epson salt is not the correct acid for battery.

I believe the salt water was supposed to be poured out and rinse the battery out once again with clean distilled water. Then refill the battery with sulfuric acid from one of your local parts store. Then it would have worked.

@vexxcloud5543

11 ай бұрын

No, the Epsom salt works as the electrolytes instead of the sulfuric acid. Although he could have filtered the old acid and just topped off the fluid with salt mixture additive after cleaning

@qua7771

3 ай бұрын

@@vexxcloud5543 It seems like a lot of salt.

@dalehood1846

10 күн бұрын

Too much Salt is bad for you.

@qua7771

10 күн бұрын

@@dalehood1846 lol. Too much battery acid is bad for you too. To much anything is bad.

What do you have in the tote in the beginning of the video? It also has some liquid. Do you have a video of that too?

Thanks for trying this out .Other attempts suggest that Epsom salts will result in a battery that will only give 9 volt but last for over five teen years .That is interesting for making large static battery banks for off grid use where 48 volts is wanted do 5 of these 9 volt batteries will give the 45 volts which works for them .The upside with salt battery it seems they don't get damaged from total discharge but they don't preform well under large loads . Many You tubes on Epsom salt replacements .Also in third world many KZread's on how to melt the lead plates and remake new battery using acid systems . LSO many you tubes an using welder equipment with 200 amps to boil battery in five minute bursts until battery works again . I have yet to see a 12 volt Epsom salt battery return 12 volt solutions for any interesting time periods so very interested for your results now 11 months on .Can it supply cranking power to start gasoline engine .I don't mind to gang together several to get cranking power for my 13 HP marine engine on my boat and for domestic us . Li thuim ion ferros oxide phosporn type Li Fe PO4 has problems with cost and expensive chargers and cold temperature charging and high temperature s and Alternator charging in marine use . Lead crystal battery costs per cycle is also a problem . We need more people to do these experiments to see if we can rescue lead acid batteries to keep from forkingbout big bucks every few years especially in warm countries where lead acid batteries have much shorter lives than temoerate regions

@timgrove4803

Жыл бұрын

It's a 12 volt battery not 48 volts

@davidhenri2722

Жыл бұрын

You wire the batteries in series to make 48 volts. That is exactly what the OP is writing about. Please read his post.

@busterhurst5723

Жыл бұрын

255 Hyatt we're3 no

@dannygann1203

Жыл бұрын

=4

@rholton6099

10 ай бұрын

motor in rear!!!

Love your videos. Arizona ROCKS !

@ArrowheadGarage

Жыл бұрын

Thank you Johnny, appreciate you watching and leaving a comment.

Great videos as always sir❤❤❤ also can we put the indicators and scan charts for reference like the Keystocks software??

@ArrowheadGarage

8 ай бұрын

Yes, absolutely

@evankirk2976

26 күн бұрын

@@ArrowheadGarage Would love a follow up with the capacity and lifetime added.

How long does the battery last after that service

"The wife gets a little concerned" LOL

@davidran9317

Жыл бұрын

She have too " LOL😊

Use sodium sulfate instead of epsom salt (Much gentler on the electrodes and does not heavily oxidize the positive plates when charging And it's even more conductive too) And it also has much higher output current than magnesium sulfate. Alum sulfate will also work as well. but its not the best choice. Just add about a tablespoon worth into each cell (Not too much!) This will raise the conductivity of the electrolyte if its weak. and also aid in forming the electrodes gently. re-forming the lead sulfates into lead and lead oxides. without over-oxidizing the positive plate like the magnesium sulfate/espom salt would I have had nothing but bad experience with magnesium sulfate and several tests ive done. it is simply too aggressive and attacks the positive electrode quite strongly. (it is fast at forming the lead oxides. but it will increase corrosion) No need to use any baking soda either or removing or replacing the electrolyte.. Just charge the battery with the sodium sulfate added to it for a long time at a low current and allow the voltage to rise to whatever it takes to accept that low current (Charge at about C1/100) Until the voltage is about 14-16v. Then the battery can be put on a normal charger and held in absorption (14.4-14.8v) for several additional hours. until the current has stabilized at a low value. Watch for heating of the battery. Take a measurement regularly if it starts warming up at any point. let it sit for several hours to cool completely. Regularly check the voltage and current as well. just to be sure theres no shorted cells or anything unusual happening You can also add about 1/8 teaspoon of boric acid or borax to each cell. as an additional additive. it creates a protective boron layer on the electrodes. specifically the negative. resistant to sulfation. if all else fails and you cannot revive the original sulfuric acid out of the lead sulfate stored in the plates. (Cannot raise the specific gravity) Only then may it be time to try replacing the electrolyte with an alternative such as alum. sodium sulfate. mixture. or baking soda (Possible electrolyte alternative could be washing soda or sodium carbonate. as it is the strongest alkaline electrolyte ive found that can still form the lead oxide in the plates. creating an almost super-capacitor like battery performance. Very tough and hard to kill. can be charged and discharged thousands of times with no damage. Deep discharge is completely harmless) You will get a significantly lower voltage though. between 8-11v so there is a drawback for going completely alkaline-for the electrolyte. PH will be roughly 10-11 if fully converted to alkaline.

@dallaslouie

6 ай бұрын

What type of sodium sulfate and where to get it.

@joebudi5136

3 ай бұрын

​@dallaslouie Thats my question. Where you buy the stuff?

Just watched from 2 years ago. Can't find the update you were mentioning. How did th we battery do over time?

Well you know once you did the baking soda clean step step and then you Drain it You can go to most auto parts stores and buy battery acid I know at least Advanced auto parts has it But I would definitely check around

after Getting the battery to take a charge but what is the cold cranking amps. I didn't see a load test. it can show volts but can it hold up while in use.

@ArrowheadGarage

2 жыл бұрын

about six months in and battery is still doing well

@lawrencebraun7616

Жыл бұрын

​@@ArrowheadGarage ❤❤

now, I see what makes a battery cell goes dead is that the lead plates inside the battery gets dirty. Again, thank you for you're video

What happened to the other half of the epsom salt solution after you mixed it? When you poured the finished solution from the pot and into the gallon jug, the jug was only filled half-way.

@peatmoss4415

Жыл бұрын

You can soak your tired feet in it!

Would have liked to have seen you load test it

thank, you for you're video

Thank you 🙏 it is great 👍 to know for less money 💵 💡⏰🎥👍👋

After dumping out the baking soda water you should have rinsed the battery a couple times with water to get all that out of battery, then before adding any of your Epson salt concoction used a specific gravity tester to test the strength of your concoction to ensure proper strength 1st before adding any of it to your battery. Filter your used electrolyte and pour equal amounts into each cell and top up with your concoction. After adding the proper strength solution to battery, then put charger on deep cycle battery setting if you have that setting. A smart charger may do the same thing by charging at different rates until fully charged over a 24 hour period or longer. I have seen batteries after trying to fix them that showed 12.8 volts but as soon as I went to turn the engine over the battery went to 7 volts and would not turn the engine over. This indicates that simply charging to 12.3 or above doesn't always translate to the battery being fixed, especially if the battery originally went dead while below freezing and as such froze up and broke some plates inside the battery. I usually use the specific gravity tester in each cell to see which cell is showing weak solution and which are showing normal, I will remove with a suction device like a fluid transfer pump or just the bubble device I am using which is the specific gravity tester, until the fluid is below the plates in that cell. At this point the strong concoction of Epson salts and water can be added just to the specific cells that are showing they are below normal on the tester. This saves a lot of time and most of the original electrolyte gets to stay in the battery. After this I put the covers on the cells and charge for minimum of 24 hours and with all of this there is no guarantees the battery will ever function like a new battery. Prevention is still the best way to look after a battery, remove either it or 1 terminal when not in use for extended periods of time, recharge every 3 months, do not store on a concrete floor but rather on a bench or wood of some kind.

@chettravirca4028

8 ай бұрын

I have to agree with everything you said here with the exception of the concrete floor. This is a myth and a hold over fallacy from the days when car batteries had metal in their cases. New batteries up today have cases made entirely of plastic. You can put a brand new battery on the concrete floor in your shop and put another one on the wood counter and check them a month later there should be no difference whatsoever.

@SEPHICHI420

6 ай бұрын

all your blabbing but its redundant. the PH of the acid will literally self balance with a charge. He could do all that but it bbn isnt neccessary on an old junky battery.

@sandymorris9293

3 ай бұрын

​@@SEPHICHI420p

So, you don't use new battery electrolyte / acid to refill the cells??

Why not just removing the sulfuric acid and doing the clean out with the baking soda why not just put sulfuric or new sulfuric acid back in

@saltwell80

Жыл бұрын

Terry where do u get sulfuric acid

@artstudio9673

Жыл бұрын

@@saltwell80 in USA it is available guessing you are from UK?

@mikeodonnell6312

Жыл бұрын

Sulfuric acid at a pool store

@terryhill4732

Жыл бұрын

@@saltwell80 you should be able to get it at any auto parts store

@artstudio9673

Жыл бұрын

@@mikeodonnell6312 In my pool store here in NY they Hydrochloric acid, also known as Muriatic acid,

You got bigger problems than a battery, someone took your engine and replaced it with a spare tire.

@ArrowheadGarage

Жыл бұрын

Finally someone noticed lol for watching Tom

@williamvolkmann8658

Жыл бұрын

@@ArrowheadGarage I have heard of white vinegar on top of 1/4th.cup of baking soda per cell . Then add your mix of epsom salt, wash it out extensively with several fillings with water, drain completely, then add back the settled acid, Why did you not add back the acid, only a charged battery holds the electrolytes in the plates, a discharged one has 80% of the acid in the liquid. Can you say why u did not add acid

@Rick-if5zb

Жыл бұрын

Don't make me laugh! 😂🤣

@boogiemorgan

Жыл бұрын

He tried, but is healing up from that .45 cal. Slug through his leg!

@fallback8314

Жыл бұрын

@tom mak, good joke, made me laugh but i'm sure you know porsche engines are in the back

With this is a temporary fix, because if you mix those two things within that battery, it’s gonna eventually corrode the lead in it common sense. If you wanna fix a real better either go buy a brand-new one or pay the money for actual battery acid be smart.

Did it turn up well?

Cool thes will help me God Bless you are Angel I am Lady willing to learn how to do the proceso tank you.

A friend of mine claims he has some ocean front property in Arizona for sale cheap.

@michaelgoins8382

Жыл бұрын

Love that song!

What would happen if you put white vinegar instead of Epsom salts into battery?

Led acid batteries consist of 2 different kind of lead plates sitting in acid. This makes electric current. The plates wear out and become the same kind but a different lead together. So no current flow. Cleaning the sulfate off will help, but charging turn the places back to their original lead type. With sulfate removed there won't be as much lead, but there will be current flow, just not as much.

Put a load tester on it to check Cold Cranking Amps. Residual voltage isn’t telling you anything.

From my experience it will worke for 2 days just enough to crank the car twice... But thank you for your efforts

I just saw a clip with a doctor recommending drinking the same to purify your stomach.... 1 Litre distilled water, 1 tsp baking soda, 1 tsp sea salt. Divide in 4 and drink every 2'nd hour... Makes sense 😂 Tip: The distilled water is polluted when poring it in a "bucket" like that...

Before you start your procedure hold the battery upside down about 6-8" inches above the pavement and drop it a time or two...If the posts aren't recessed zip tie a piece of wood to it first... sounds crazy but trust me.

@michaelwarren3853

Жыл бұрын

It sounds like youve been smokin some of the new stuff.or ya need to .

@ethelb6023

Жыл бұрын

sounds good to me! Ha. You need to physically break the seals between the pieces of lead, so the liquid can reach all the lead. Am I right?

@michaelwarren3853

Жыл бұрын

The plates in a battery have seperaters between each plate..without them the plates would simply short out .

@tomupchurch4911

Жыл бұрын

@@ethelb6023 it's like a head start to loosen the calcium.

@tomupchurch4911

Жыл бұрын

@@michaelwarren3853 it's like a head start to loosen the calcium.

A Question can a guy reuse the old battery acid ? Run it through a Coffee filter ?

Yes a load test will check to see if you can pull a load. Easier yet. Let battery sit overnight and recheck voltage. If voltage drops it’s not going to work. But a load test is better. But if you don’t have a tester check voltage and recheck 24-30 hrs later. If it drops from 12.6- 12.0 it’s not going to work . Nice video . But remember to load test it as well or sit and watch for voltage drop.

@heleymady3517

Жыл бұрын

hello ......how are you doing??

I'm aircraft avionics tech. You makes me smile.

Need to put a load tester on and see if it really holds the load

@junkvista61

Жыл бұрын

Yes, this is "half baked" thing. The result is not convincing as later he admitted it that he have to buy new battery. just waste of time.

@paulnicholson1906

Жыл бұрын

@@junkvista61 the battery had over 12V to start with.

Drain battery and flush it with a garden hose, then one rinse with distilled water. That dislodges any particles of plate material that build up on the bottom of the n battery and might be causing slight internal short circuits between the plates

@earthorigins3509

Жыл бұрын

Most important... Pour distilled water back in the battery for the final process..!

i just add table spoon epsom saltzto each cell let set over night it desolves crud on plates

👏very well done, kinda, yes the plates will create a build up, and this build up flakes off over time and settle in between these plates creating a short circuit. Getting this gunk off and out between these plate is a must along with putting new acid in but if you first filtered the old acid and poured back in and connected a old none smart charger and forced charged that battery on high ,,not the start setting,, and let it set a few days. Battery would have become warm, bubbles would have appeared and alot more flakes would have come off. Then shake and pour out. Put in new acid and charge. !!BUT!! a smart charger, A charger with a chip, will not force charge any battery. A old transformer type charger can bring back a completely dead battery, a smart charger would see it as a short circuit a (bad battery)and kick off. They do this even on a week battery that won't take a certain amount of charge over a certain amount of time, they just kick off.. old chargers, they charge using a transformer, not through a programed chip that's also design to test the condition of a battery and that's what they all do, and if a battery isn't in near perfect condition these charger just keep kicking off. Look for at Flee markets. Garage sales, maybe ebay? . I just found another one for 10 bucks at a flee market in great condition and if you had it on that battery you would have seen over 14 volts on your volt meter forcing a charge on that battery. You read 12 volts with charger connected to it, your charger kicked off...a bad battery can show 12 volts, but it's about available current (amps) that does the work,, you can sometimes get a little more life out of a old worn battery, but not with a digital computer chip charger. These Chargers are much cheaper to make and sale. Get an old one to have around and you won't be replacing your riding mowers, ect, batteries as often either.

@logantruitt2822

Жыл бұрын

i can vouch for this. i used an old laptop power supply and soldered in some battery clamps on the output and it'll easily charge to as high as 15 to 16 volts if u let it sit. im not sure how good that would be for a battery under normal circumstances to be charged that much more than its intended output, but for this use, i think it will be ideal. i guess i'm gonna find out as im about to attempt to refurbish my battery in the next day or so.

@James-mo5lh

Жыл бұрын

I have an old transformer type charger but it doesn't work anymore. Do you know anyone that fixes them . I'm not sure what the problem is or if it's worth fixing

@terryayers6179

Ай бұрын

Dunno if u have a tractor supply where u live but they still sell the old type chargers for like 60 bucks I have 1 of them and also an old charger that's about 30 yrs old just because I hate the smart chargers for the facts u stated we had a battery totally dead and all we had was a smart charger kept kicking off so we didn't have jumper cables at the moment do now anyway we took 2 pieces of coated wire and hooked the dead battery to a fully charged battery for about 30 minutes enough that it would spark and the smart charger finally recognized it didn't have a short in it and finally charged it

Do u know what ahydrometer is oh and maybe a load tester u just junked a good nattery

Can't you just dump the old battery acid out and put fresh battery acid in and be done with it. Jim

@biborski

Жыл бұрын

Well, aparently you can't, I live in croatia, europe, there is no acid to buy in stores, even mechanic shops are banned from buying acid for batteries, there is no acid to buy

@samaro5647

Жыл бұрын

As long as the lead boards inside are still intact just replace the acid and your good to go however the lead boards are what causes a battery to fail because of the caustic nature of the acid and they have cut back on the amount of lead in the board's they start to warp and when they start to touch you get a bad or weak cell and then it will not hold a charge I get it how frustrating it is to have to replace your battery but the best trick to extending the life of your battery is use a battery tender if you are going to have your car parked for any amount of time over a couple days and keep it always fully charged I can make a battery last almost 10 years and I live in the worst environment there is for a battery the Arizona heat is very hard on batteries

If there is no damage something you just need to charge it for 3 straight weeks to get it like new condition. In rare cases yes you have to buy parts for them

you need to remove your Epsom Salt water rinse it good, and filter your aced you drained out put it back with a little Epsom Salt in each cell then charge it heavy then see what you get, works better that way.

@Jerry-up8bk

Ай бұрын

It's NOT EPSOM salt It's Baking soda!

Where did you recycle the old acid?

How many people can do all this? Have the equipment? I buy a new battery when due. Thanks

Wow. I clean my bong the same way

Would you do this with a battery that's starting to act like it's losing its charge and not completely dead and another question is have you considered hydrogen peroxide to go in there and boil out the lead plates just questions no idea what I'm doing

@terryayers6179

Ай бұрын

Hydrogen peroxide is extremely dangerous if accidentally mixed with acid directly so I'd say no

THAT is a classic. I think that's the only 911 I'd want.

@ArrowheadGarage

Жыл бұрын

I just love the short wheel based long hoods!!! Thanks for watching and dropping a comment, I appreciate it!

I buy those jogs of sulfuric acid from any auto parts store, and then drain and refill. Now this has worked for say, 6 out of 10 batteries I've tried, and my best guess for the bad ones, is damage to cells, or extreme contamination since I've never 'rinsed' or cleaned any of them. Using these ingredients is even cheaper.

@gregschroer2314

Жыл бұрын

How much does the sulfuric acid replacement at the auto parts store cost?

@WilliamJones-sf5pt

Жыл бұрын

Doesn't the positive side of batteries actually deform? I heard that two used batteries will give you two almost pristine negative sides to combine to make an almost new battery with.

Better yet, do the recommended maintenance, such as topping off with distilled water; make sure the alternator is in working order; belts tightened, etc.

I like to tinker so I'm gonna try this but how much is your time worth? Thanks for the video.

@ArrowheadGarage

Ай бұрын

The battery lasted about 2 months, before I replaced it.

Nice ride

why did you check the load with the battery charger on yes it will show you the voltage of the battery charger you did not check the voltage after the battery charger was unhook.why

@stefandieter7136

Жыл бұрын

Hello it's nice connecting with you, how's it going with you over there?

Work with agm?

I'm all about saving money and fixing things but really just get a new battery or used. It is interesting though.

What did you do with the original sulphuric acid you took out of the battery? Will you be reusing it again , if not how do we didpose of it?

@billmeade9029

Жыл бұрын

You can neutralize sulfuric acid with baking soda and water then if ok to dispose anyhow you want

@nickcoppard5335

Жыл бұрын

Makes good toilet cleaner

@ozarkarky

Жыл бұрын

Pour it on a fire ant mound 😋

@josehonoridez1085

Жыл бұрын

Get an alkaline substance to neutralize spilled acid. Ash from a wood stove may be used if nothing better is available.

@teresamccoy596

3 күн бұрын

That's what I want to know!!!!! also ...

how does this chemical process repair Plate Area loss??

You need to rinse out batt after the initial 24 hours of the distilled water and epsome soak. Rince out batt several times with regular tap water. Then make some more epsome salt and distilled water mix and add to batt cells. Charge for 24 hours on slow charge. Now its a new battery.

@peteleadlove9215

Жыл бұрын

You're pretty smart on this one lot of people don't know that

@rickpaz9562

Жыл бұрын

Wrong you need new electrolyte which is sulfuric acid after initial cleaning. You can buy it at some auto parts stores.

@peteleadlove9215

Жыл бұрын

@@rickpaz9562 you do it your way I do it my way

Don't drop or rattle your battery too hard or the lead plates will dislodge and your fucked. You do want to slosh the baking soda/distilled water solution in the battery though, just not crazy hard. You know what I mean? Anyway this method worked fantastic with my battery. It's only 2 years old, but I don't use the vehicle very much. I did go to Harbor freight and buy a cheapo $10 trickle charger with the solar panel. I've heard good reviews on it, so I'll have to see. I payed $150+ for the stupid battery a couple years ago and it's already gone up to almost $200. This is January of 2024.

can't find follow up on this video. so what happened? how long did the revived battery last? thanks.

@kevintanner4567

2 ай бұрын

Anything yet from this man?

I paid 497 dollars for mobility scooter batteries in 2021 in Australia.

Mr arrawhead garage may I ask you somthing does baking soda,salt, and water will work on any battery

@ArrowheadGarage

9 ай бұрын

I think so, this hack lasted a few months for me.... being in Phoenix Arizona USA where its 120F in the summers its hard on batteries.

How many battereries today are tamperproof

So what did you do with the old battery acid?

@ArrowheadGarage

Жыл бұрын

My local county has a recycling location that takes just about anything you have to dispose of.

Ive seen 100% better batter rebuilds by guys sitting on dirt floors in India and 100% theirs actually worked.

@tomm8554

Жыл бұрын

Send us some links.

How much epsom salt in the bag?

I have used distilled water and it worked.

Update video! ! Please and thank you bro !

So you're just saying after 2 days of charging it did not work. Now you want to charge it for another day. What about doing the load test on it after you get a voltage reading. Need to see that. Jim

Quite an interesting video, but I would have used pure concentrated sulfuric acid instead of the hydrated magnesium sulfate solution with the distilled water. Handling this strong acid is risky if it splashes on you though. May be you are better off just buying another new battery. The consequences of a splash from sulfuric acid could be permanent. It is the strongest industrial acid out there. It could go through your cloths and into your skin in an accident. Always be careful if you mess with chemical agents, electricity or gasoline components. I usually stay away from them.

@richardtackett7597

Жыл бұрын

I once drained the 10% acid and replaced it with 20%. Fi ed the battery for three days. On the third day on the way home from work the battery exploded and blew the hood off of a 1982 ford Ltd. .

@carle5538

Жыл бұрын

@@richardtackett7597 Wow, that is bad. It is best not to mess with such things. Just invest in a new battery. Thank God you were not injured.

@ScaredCivilian

Жыл бұрын

You're supposed to dilute it

@terrytorkildson2831

11 ай бұрын

Using the Hammett acidity function: Helonium: −63 Fluoroantimonic acid : −23 Magic acid: −23 Carborane superacids: H0 Fluorosulfuric acid : −15.1 Hydrogen fluoride: −15.1 Trifluoromethanesulfonic acid: −15.1 Perchloric acid: −13 Sulfurochloridic acid: -13.8; −12.78[11] Sulfuric acid: −12.0

@Kj16V

11 ай бұрын

​@@terrytorkildson2831"magic acid" Wait, what??

Can I use iodized cooking table salt instead of Epsom salt???

@ArrowheadGarage

Жыл бұрын

Jude no you gotta use the epsom salt on this hack!

load test?

Try reversing the polarity after flattening battery, & charging.

so does that mean I need 27oz of Epson salt for the 1gallon?

You really did a good presentation and it's commendable. Thanks for your honesty there. But did the end product work? Next time, while your process was convincing and tempting to attempt, we are interested in the full result, otherwise you wasted a nice presentation which resulted only in wasted viewing time. But you presented your process very well. Result, that's what we want, don't you think?

@ArrowheadGarage

Жыл бұрын

Howdy Henry, sorry I didn't show putting it back in the car. It did work and lasted for about 3 months or so. In the end I did just replace the battery with a new unit. Thanks for reaching out.

@henrybermudo6894

Жыл бұрын

Except for the final proof we needed and anticipated, you did really well in the " how". You should further your presentation by reverse engineering the battery, showing us the actual inside, it's parts, how they are put together, how they interact. It's a valuable lesson to really have, needed where the acquisition of a new battery is next to impossible. Your teaching is one that makes a man to survive from next to nothing. Buying is not teaching. I go with your style. Teach a man to fish and he'll live a lifetime. Let him buy and he'll expire with the battery. Your presentation is a great intro, but walk us to the end where we see our efforts rewarded. Thanks. By the way, it's the American spirit in you " never give up ". I'm proud of you! We, veterans, fought to keep our nation alive so you with that American spirit can continue to encourage the world to " never give up if there's even a sliver of possibility ".

Maybe, just maybe add a step between the bicarbonate flush and electrolyte fill: a rinsing away of ALL bicarbonate that might be hanging around down in those plates somewhere...

Where do you dispose of the waste?

Man you did an awesome job on that firebird, it looks like a Porsche now. Hahaha God bless

@ArrowheadGarage

2 жыл бұрын

lol amazing what some bondo will do lol

So I been watching these type of videos recently.. I noticed he didn't wash the inside of the batteries with a hose and also didn't say if he charged up the battery to max beforehand.. also before adding his new electrolyte he didn't flush the battery with distilled water 1st to wash out the baking soda that definitely caused more bubbles.. I have been reviving batteries with a stick welder but wanted to try flushing them an adding either new acid or filter mine or this Epson salt technique.. I haven't decided.. new acid it probably best