Thank you so much for this video! Just saved me 700$ that I was quoted for this fix. It took me an hour to do. Life saver video

@92813justin

7 жыл бұрын

You are welcome, Nick! I am glad I could save you some time and money!!

@petko618

6 жыл бұрын

Hi. Thanks for the video. My '09 F150 has the same issue. Stuck in cold air. Did you needed to pull any fuses or set the temp selector to various settings for a few seconds for the system to 'learn' the settings again?

@92813justin

6 жыл бұрын

Great question. Everything works out great. There is no need to do that.

@jesusm285

6 жыл бұрын

Hi, my 2011 f150 is not getting any hot air....should I do this to fix it?

@jesusm285

6 жыл бұрын

It's just not sending any hot air in the truck

To save time on the hidden rear screw I was able to remove the first then lift and rotate the old actuator to the left. It exposed the back screw for fast access.

You rocked it! Best video compared to ALL of them. Good job young man! DIY $23 vs $ 450 at mechanic was the right choice.

Good video and helped me replace the actuator in my 2010 Ford F-150 XLT. I would add that you need small hands to get in through glove box and on top of actuator. Also, tie string to your small wrench and back screw to keep it from losing it. Price of the part runs between $22-$3

Man thank you so much, took me about an hour to replace. Save me a lot of money. God bless you.

Thanks for this posting this. It was a huge help; I've never changed this out before and your step by step guidance made it doable and easy. Appreciate it!

Perfect video! Very helpful and I fixed it on my 2011. Took about 2 hrs start to finish.

Thank you for the video man! Super helpful and great info. I also just snapped the back bracket off and left the back screw off when I put the new one in. Plenty of hold with just the front one. That back one is just way too difficult to get out. (2010 f150).

Thank you! Just finished. I plowed through several of videos for this, you win. Awesome, thanks again!

@92813justin

3 жыл бұрын

Awesome, I am glad you got it done. Thank you

Just wanted to say thank you for this video. It really helped me figure out how to get in there to get this cursed beast out of my vehicle and restore the heat. Just a helpful FYI for those who are still attempting this, the wiring harness in the glovebox needs to be popped out of place and moved down so that you can really fit your hand where it needs to go. And the tool that you'll likely need to fit in there is a simple small 5/16 box-ended wrench. (A ratcheting one would be best)

@92813justin

5 жыл бұрын

Thank you Brian! I'm glad the video helped you replace this horrible actuator.

@dopeman420

10 ай бұрын

8mm.

Great video. Job took about 30 minutes. Ford replaced it the first time under warranty. They didn’t put the rear bolt in that probably saved me 15 minutes. Thank you!

@92813justin

6 жыл бұрын

Phillip Roten Wow. That is funny Ford left out the bolt. It took some effort but I'm glad it worked out for you!

Just finished installing the actuator and I am happy to say, WE HAVE HEAT! One thing slowed the process, the gears didn't line up so contrary to the advice given to me at the Ford dealership, I did NOT "Stick a screwdriver in and force the gear to move". Just plug in the new actuator and turn the heat/ac knob until the gears line up. Easy fix. Thank you so much for posting this video!

@JohnJohn-nh5mj

Ай бұрын

I put new peace and keep knocking. So I need to move the ac/heat till line up? I will try it again…

Thanks for your video. I just finished replacing the heater blend door actuator on my 2011 ford f150. That back screw was a pain. However, I couldn’t use a small ratchet to remove it. Instead I used a small 5/16” box wrench. Took less than 5 minutes. Thanks again.

This video helped so much. Save yourself the trouble of removing the back screw!!! Remove the front screw, insert a flat blade screwdriver or small pry bar underneath and pry up to break the back tab. Damages nothing!

@TheSaintberzerker

2 жыл бұрын

now you're talking! thanks!

@dopeman420

10 ай бұрын

INCORRECT. DO THE JOB PROPERLY

@glennbenoit4958

7 ай бұрын

ok thanks karen@@dopeman420

@glennbenoit4958

7 ай бұрын

I did exactly that ,I then just left the rear screw out as one screw is quite sufficient

@prestonmossman5109

3 ай бұрын

This was the best suggestion in the thread. I have no clue how to get the screw out any other way

Quick question, if I have the dual climate control and only want to replace the actuator on the passenger side, will the removal of the radio panel and replacement be the same as in this video? Both aren't working, but I'm looking for a halfway fix that I can live with at the moment and can't find anyone working on the dual replacing only the passenger side. Thanks.

I did this repair on a 2013 F150...fully expecting to battle the rear screw, was very fortunate...there was none!! Maybe the engineers at Ford realized that this wasn't such a better idea. Thanks for the video post it was a useful guide :)

@dopeman420

10 ай бұрын

More likely someone was already in there once....use your brain fella....

Thanks for sharing this. That back screw was a royal pain, but A $25 part and this video saved me a lot of money.

@92813justin

4 жыл бұрын

Probably saved you $700 doing it yourself

Super great idea about only loosening and disconnecting the plastic surrounding the radio. Saved me tons of time, and now we have heat!

@92813justin

3 жыл бұрын

Great news!

Dude the best do it yourself video. You saved the day. Good job my man. Continue making more videos !!!

Thank you!.... just did a bunch off work to my truck... reset the pcm and the actuator went out.... your video is the best guide... only took about 1/2 hour... would’ve been faster if I didn’t have 10 thumbs.

Great video! Clear and to the point. Just fixed this on my 2012 XTR (XLT) in about an hour. Prince George Ford charged me C$70 with tax for the YH1933 part.

Great video dude! Mine just quit working completely. I live in Arizona. Am going to attempt this fix at night with a cooler blowing the sweat off me. Wish me luck and thanks again!

Any info on the bolt head sizes being used?

Good info, I have cold ac blowing well over evap but not getting to vents. I cut small Sq to access evap & blowing well. Vents have very little air flow, Thoughts?

Thank you for this video buddy. I changed mine last week following your steps. I actually posted a video, I found a better way to get that motor out without having to mess around with that back bolt. I just took the front one out and grabbed the actuator with a pair of pliers until I snapped the ear off the back of it and then had easy access to get the bolt out. Thanks again

@92813justin

5 жыл бұрын

You are welcome. I watched your video and gave it a thumps up. Great work!

@dalehead5397

5 жыл бұрын

Thanks to both of you.

@apac102b

5 жыл бұрын

Great video guys I am only getting cold air so it seems this will be a fix correct? Would love a yes? Does this also fix the clicking noise as well? Hopefully you guys see this question. Lol thanks

Good video, followed it and got it done in 1 hour.

Thanks for a great video. Gave me everything I needed to get the job done. More information to explaining how to get that back screw out would have been nice. I used a 5/16" wrench and had to remove the separate the wiring harness under the dash from the frame but it all worked out and was exactly what I needed to get it fixed. Thanks again.

Great video, saved me tons of money and didn’t leave me with any questions

@92813justin

3 жыл бұрын

Awesome!

After i watch this video, i did mine in just 30 mins. save my money and time, thank you!!!!!! 👍👍👍👍👍👍

@92813justin

4 жыл бұрын

You are welcome! I am glad It worked out!

I have dual climate control what do you think I need to replace the driver side too

What do you think maybe need in otter part for the ac

Will this fix the heater to that it can work again? I'm having this issues and now that its winter time my truck dont want have heat. Only cold air.

Thank you for the easy to follow video. Well done!

@92813justin

5 жыл бұрын

You are welcome. I am glad the video helped you out!

Excellent video thank you. Heard the clicking noise all last winter. Didn't think anything of it until the first cold day of this season when it finally gave up the ghost. Looks easy enough except for that screw!

@92813justin

4 жыл бұрын

Game of Life that’s exactly what happened to mine! Haha

Do you know if a 2015 KingRanch is the same as these model year? My dual control on the passenger side is stuck on cold temp and wont sync back to heater mode.

Thank you, this helped me with my 2011 f-150 xlt. I had to grind a little over a 1/4 inch off my 1/4" drive socket to get the back screw out. It took about an hour +$15 part. The video was well thought out with the fat cut out. Great work!

@ericmiller8596

4 жыл бұрын

I have the same model and year. Is this part what causes the ticking sound with the AC?

@jmboyd78

4 жыл бұрын

@@ericmiller8596 for me it didn't click, but I replaced one in my wife's 09 taurus and it clicked loudly

@ericmiller8596

4 жыл бұрын

jmboyd78 and it fixed it?

@jmboyd78

4 жыл бұрын

@@ericmiller8596 yes, replacing this fixed the ac in my truck (mine was stuck shut) . Replacing the one in my wife's car fixed the clicking noise.

@jmboyd78

4 жыл бұрын

@@ericmiller8596 www.amazon.com/dp/B00OAKGWNA/ref=cm_sw_r_cp_apa_i_2U--Eb2ZB9EBB

Hi am facing an electric leaking inside that section fuse 39 20A Radio, Navigation display do you have any idea about the issue or where to look exactly ?? thanks bro

I have no heat in the driver side, and the back seats as well. Do you know if once switched out the actuator, will it also fix the back seats heater?

You are pro.. thanks a lot, I saved lots of money and it was so easy , tools me only 1,5 hours. Wish you the best and keep making video like that. Super helpful

@92813justin

4 жыл бұрын

Thank you! I am making as many videos as possible to help people

man thank you so much!! That back screw game me a lot of work but finally got it out!!!! watched lots of videos, but this is exactly what I was looking for now my AC works perfect. Thank you

@92813justin

3 жыл бұрын

Perfect!

@luciaarmenta9920

2 ай бұрын

Quick question. Was you AC blowing hot air before you changed this out or not blowing at all? Thanks!

@adinmartinez5453

2 ай бұрын

@@luciaarmenta9920 it was only blowing hot air

Something I did to align the splines was to plug in the new actuator and turn the key on. It moved into the position the old one was in. Went in easily! The real hard part was that back screw.

Nice job and thank you for the video very well done and saved me a ton of money doing it myself.

@92813justin

4 жыл бұрын

All Out Throttle You are welcome, I’m glad it worked out for you!

Is this also the fix for when your heat is stuck on? All the research I’ve done points to this

Would it help with getting the correct shaft position to compare the old and new actuators before you install the new actuator. If not the same then manually move the new actuator to the same position as the old one. Then you should be able to align it to the correct position easier. At least you'd be starting closer to where you need it to be.

Excelent vdeo was very helpful thanks.

Thank you very much. I have done this job twice now and this way saved a lot of time. Last time I took all the plastic trim pieces off. This is much better. I did it in about 2 hours. Dealership booked it at 8+. Thanks again!

@92813justin

7 жыл бұрын

That is because they "might" have to take the whole dash out. I am glad you found my video helpful!

Any clue if it is located somewhere similar in 15+ F150s?

Just a tip, if it hasn’t been mentioned yet. To line the keys up on the Actuator; all you have to do is turn on the truck and slowly adjust the hot/cold knob until it pops into place. Make sure you have the blend door plugged in. And as for the radio console, all I unplugged was the upper plug and the plug on the right upper side. I left all the plugs on the bottom like the video. So to recap, get the blend door in the right orientation, then adjust the knob so it matches the key on actuator

@dopeman420

10 ай бұрын

It will automatically do that. Just install it. Your over thinking it.

@ksaum74

6 ай бұрын

That actually sounds like a great way to get the splines to line up. Thanks for the tip!!

I have hot air blowing out the 2 driver and rear seat vent's when a/c is on but cold air coming out the 2 passenger vent's.Does this sound like the blend door actuator also?

How long did that take? I have the same problem. Thanks

there are some clips offer some tricks on how put the new one in: just use (cut) the bad actuator gear tip, slid gear tip in , and twist to the desirable position for the new one to be in.

@rdzed3505

2 жыл бұрын

I was going to point that out. All you need to do is open up the old actuator, pop the old gear out and use it for alignment. No need to cut anything and it gives you a BIG gear to hunker down on for alignment. Cheers.

Thanks for the video. I am going to try it tomorrow morning!

@92813justin

6 жыл бұрын

40judo You are welcome. Good luck with the fix tomorrow

Right to the point.... Damn I wish everyone else would do it like this👍👍👍

I know it's about 4 years old, but dude you are still a champ saving tons of people tons of money. LMAO bout to work on this for my truck too. :

@92813justin

4 жыл бұрын

Nicholas Willcox, thank you! It’s not a bad fix if you have time and you save so much money from Ford “taking the dash off and replacing the actuator for $700” lol.

@danielsandoval634

3 жыл бұрын

@@92813justin Is this the same component that makes a click sound? Currently the sound is coming in that from the video. The sound clicks for 4-10 times.

@92813justin

3 жыл бұрын

Daniel Sandoval most likely.

@nicholaswillcox

3 жыл бұрын

@@danielsandoval634 yeah so ...mine was literally doing the same thing. This will fix that and...I dunno if anyone else had this or not but my AC works like a BEAST! now after fixing it.

@danielsandoval634

3 жыл бұрын

Is there an actuautor on the driver side?

Are you able to rotate the door by hand if you try and turn it with your finger? To line it up?

@92813justin

6 жыл бұрын

Great question! Yes, only on the part that is attached to the truck. You can not move the actuator. I was able to get both somewhat lined up in order to have the actuator slide in. Then, I move the actuator to line up the holes.

@AOT-offroad

6 жыл бұрын

Just a tip for everyone else what I did was look at and mark the location of the arm on the old one I removed and then plug in the new one and rotate it with the hot/cold control until it matched. Then I installed it easily

Do you have dual climate? If not do you know if dual climate zones have two blenders. And where the hell would the other one be? Wish me luck I'm going to rip into this tomaro.

@4wheelinRedneck2

4 жыл бұрын

Its under the dash near the floor. There is a video on youtube

Thanks for the video. I'm looking to clarify the symptoms of this failure. My dual control passenger side temp no longer changers temp when the passenger control is changed. Is that charistic of the problem this fix solves?

@92813justin

5 жыл бұрын

Kim yes, sounds like it could be the issue

@005preetham

3 жыл бұрын

Kim, did you try replacing blend door? I am also having same issue.

@TheRobkwill

3 жыл бұрын

No, in have not yet attempted to fix the problem.

How do you know if it’s this part or the blend door motor under the passenger floorboard ? Our clicks on hot or cold but I don’t have hot air on the passenger side . The drivers side has hot air but still makes the clicking noise off and on

Great video, love your straight forward style and high-speed….my problem is not hit or cold….it seems my front vents do not blow or at least not hard…in fact it seems to make no difference what location I set (eg. feet, vents etc) it seems to blow 80% at my feet and 20% everywhere else…..not sure this would fix it?

@92813justin

2 жыл бұрын

Seems like a blower door where they direct the air

Thanks for the video. Do you recall the socket sizes that you used for the screws and are they all the same sizes?

@92813justin

7 жыл бұрын

Thank you! The screw to take the blower door actuator off is a 5/16in screw. I do not remember the other sizes however the sockets sizes are small and very common if you have a set. You can also check out my description for more details.

Couple of things to add to this video since I just finished the job on my 2010 F150. I don't think you needed to take off the bottom four bolts. I removed my radio some time back and did not remember doing that so I skipped that step and it still came out fine. I am glad you mentioned the part needing to be aligned before it goes back in. What I did was plug it in, turn on the ignition and AC and moved the temp selector switch until the gear on the new part was in the same position as the one I removed. Then it went in pretty easy. Well easier anyway - nothing about this small job is easy. Like you mentioned the hardest part is getting at that back bolt. Especially with my gorilla size hands. I ended up using a six point boxed end wrench which worked okay for getting it out, but I could not get it back in and lost it trying. So I just left it out all together and it seemed to be plenty tight with just the front bolt - I hope so anyway. Very helpful video.

@92813justin

2 жыл бұрын

Thank you for the intel

I've recently had an issue where the heater in my 2014 F-150 will intermittently stop blowing heated air. It'll be working fine and then all of a sudden you can feel the air coming out of the vents start getting cooler and cooler. If I fiddle with it a bit, or turn the control panel off and back on it seems to start working again. Is this video the fix for this issue? I didn't see anywhere what the symptoms are for needing this repair, so I thought I'd ask.

This video is 100%. I was able to replace in under 2 hours. For the back screw I used a 8mm socket. There is plenty of space behind the motor for the ratchet. You just need long arms

Thanks for the video. In your experience replacing this part, will it improve air blowing speed as well as temp control? I only have hot air that blows out slowly in an Explorer. I appreciate your thoughts!

@92813justin

6 жыл бұрын

Steve Kunkel good question! This actuator only controls temp. There is a different system that controls the speed

@teddybanks4270

5 жыл бұрын

Sounds like a bad blower resister.

I have a 2011 XLT with no dual climate. My temperatures work just fine but when I first turn the truck on there seems to be what sounds like gears clicking behind my radio. Any ideas? I already ordered a new actuator just haven’t got around to replacing it

@92813justin

6 жыл бұрын

It is hard to tell where and what the clicking noise is in your truck. Take a look at this video and listen to your car to see if it is in a similar location. If it is, then it may be the actuator. This actuator made some weird grinding and droning noises before it went out. Hope this helps! Good luck

Excellent video!

@92813justin

6 жыл бұрын

Thank you!

Thank you so much for posting this video. I have a problem with blend door actuator in my 2011 ford mondeo mk4.5 dual zone control, it's noisy and stuck in the middle between cold and hot air. The question is should I remove the whole dashboard or just remove the center console to reach the dead part? Hope that you giude me to the right direction.

@92813justin

6 жыл бұрын

Mohammad Mustafa you are welcome. I am glad you enjoyed the video. I would recommend taking out as little as possible. That will help prevent you from breaking or loosening your dashboard as much as possible. Because it does not always snap back in perfectly the second time. At the end of the day it's up to you but I would stick to less is more in this case.

@mohammadmustafa4915

6 жыл бұрын

CluEngineer thank you for your prompt response. Well, in this case, I will go to some professional to do this heavy duty job.

I have a 2013 F150 Eco Boost that will only stay very hot until i bring the cold knob almost completely to the left side. Is there a difference between the blower door actuator and the Blender? WIth this occruing do you believe its the blower door actuator>

@92813justin

7 жыл бұрын

The blower door actuator and blender door are two different words that describe the same thing. Have you tried your issue with the air conditioner on? I would try that to see if it is moving smoothly. Make sure to listen for the actuator when you are changing the temperature. If it skips really fast right when you move it to the far cold side that may be your issue. If that is not the case, something may be wrong with the cooling system.

Have a 2014 F150 fx 4 ac works but the fan that blows the air quit on me. Can feel the color air it's just not blowing. Any ideas on what it is?

Yes, because when I replaced the part I moved on the side how can I fix that

Did mine today...very helpful...went very much like the video...didn’t overstate the difficulty of the back fastener! Thank you!

@92813justin

4 жыл бұрын

Keith Wyss, I’m glad it you got it done and everything is working!

@ericmiller8596

4 жыл бұрын

How do u get to the back one? I’ve tried a socket and a wrench and can’t get back enough to turn wrench or socket. I have the clicking issue

@keithwyss5218

4 жыл бұрын

Eric Miller I ended up breaking the old one- large flat blade screwdriver between old actuator and the housing...didn’t take much- then remove the old screw and broken tab.

@ericmiller8596

4 жыл бұрын

Keith Wyss u didn’t break the whole to screw it down?

@keithwyss5218

4 жыл бұрын

Eric Miller No, the ear of the old one broke- wouldn’t matter though- front screw and a plastic stub hold it plenty securely.

GOOD INFO. i couldn't get to the back screw with my hands , so broke the tab off by lifting up and prying the actuator. Also, I plugged in the connector to the new actuator first before putting it in place because the blend door and actuator did not line up for easy placement. Turned car on and turned the temp knob a little. now new actuator dropped right in place.

great video. i seen others and they are taking off way to much thanks again.

@92813justin

5 жыл бұрын

jojolozano you are welcome.

I was told by someone that my blend door is the reason my heater isn't blowing hot and defrost is completely cold. Top radiator hose is about 40⁰ hotter than the bottom hose. Flushed the radiator, new coolant, new radiator cap, new thermostat. Would this have anything to do with the blend door actuator?

My 2011 f150 has dual climate control and the passenger side will go from hot to cold, but it blows hot air thru the vents and not the floor. Would that be the same actuator as this one?

Do you have to do anything to make sure it's alined with how control knob is set? So if the knob was all the way to heat when you disconnected how do you make sure the position of the blend door matches?

@92813justin

6 жыл бұрын

Richard Streeter Ford designed the part so there is only one way for it to fit.

Thank you thank you thank you I did it And saved myself a lot of money. Thank you from St Paul, Mn

@92813justin

4 жыл бұрын

You are welcome. I am glad I could help :)

@falsealarmno

3 жыл бұрын

How much money do you think that you saved?

Great video, easy job

I read somewhere on another forum that you are supposed to calibrate the potentiometer. Is that what everyone else has done?

the actuator only ticked when the heat was on and then when I got the stereo panel off it started ticking when the ac too and air comes out for a few seconds and stops and goes through the vent where the windshield is. I didn’t wanna mess something else up so I just put it back together

have 09 150. no heat coming from passenger side vents or defroster? Thank you Kevin

@fixitwithzim

5 жыл бұрын

18winsagin what did you end up fixing to solve this? Mine doing same exact thing. Thanks

Great video, not sure if my issue is the blend door actuator. Most of the clicking occurs when I press the power switch on or off. Has even happened when I open one of the doors to enter the cab. Any thoughts? Thanks!

@92813justin

6 жыл бұрын

Does it sound like the blower is making a clicking noise? When you change the speed of the blower does it change?

@mikeandlilasharp2801

6 жыл бұрын

Yes, it's very subtle but you can hear the gears moving in the motor. Changing the blower speed, temperature, turning the ignition on/off AND opening doors will cause the clicking noise. After hearing that there are three motors I want to make sure I replace the correct one. Thanks.

@92813justin

6 жыл бұрын

That is really weird. Mine did not make any noises when it broke. It just stoped working. So it may be something else. Its hard to diagnose it over comments. lol. Good Luck

@mikeandlilasharp2801

6 жыл бұрын

Thanks! One last question, do you know if all 3 motors are the same?

@92813justin

6 жыл бұрын

I would assume they are different parts since they perform different functionalities.

My 2013 F-150 only blow hot air never cold and has a loud clicking behind the dash. Is this problem remedied by switching out this part?

Thank you video was very helpful only took an hour. I took out the front screw took Chanel locks and broke the back tab off exposed the back screw very easy to get to then. putting back in not so easy. Again THANK YOU

@92813justin

3 жыл бұрын

You are welcome!

My 2012 FX4 f150 has just started blowing hot air out on the left two passenger side vents up front. probably the blend door stuck. BUT is there a fuse I should check first? I cannot see anything on fuse chart in owners manual that looks like blend door

@92813justin

5 жыл бұрын

The fuse chart may have something like blower, temperature control, more most likely climate control. I would check all of the fuses that are in the vesinity of climate control. If everything looks good, it maybe the actuator. Good luck!

Great video. My question is, if I can change the climate control to different parts(defrost, legs/defrost, whole cabin) and it cycles to each different section, is the blend door my issue? That part changes the blower door to run to the different areas of the truck? I have no heat @22° but blower blows cold air fine. Temp is right where it should be. Thanks

@92813justin

4 жыл бұрын

The blend door actuator changes the temperature of your cabin. There is a different actitud that changes where it is blowing. If it’s stuck at one temperature it’s most likely the blend door actuator (unless you’re heater core isn’t working). But with these f-150 it is typically the blend door

@petertimpson9378

4 жыл бұрын

@@92813justin Thanks for getting back so quick. It seems to be blowing at the same temp. I've had my 1st 3 vehicles(starting 35ys ago) with blown heater cores and always smelled antifreeze. I don't smell anything. Not sure if the smell matters. I'll order the part. Thanks again!

@92813justin

4 жыл бұрын

Peter Timpson it sounds like the blend door actuator. Let me know if you have any more questions when installing the part

I’m having problems with the in my truck and showing how to get to it thanks

What was the truck doing that you changed out this particular actuator? Was it blowing heat on the passenger side? Was it clicking?

Nice work and video

@92813justin

5 жыл бұрын

Thank you Gabriel

Hey, can I access that way the heater core and hoses, I have no heat and can see a leak, thx

@92813justin

4 жыл бұрын

That would be tough

Great video, I think this is the issue on my truck is.. but I wanted to give my conditions and see if you agree: The heater and a/c both seem to be working fine in regards to temperature, however when I change the climate setting to blow 'face only', it triggers a loud clicking noise. However as soon as I change the climate setting to anything else other than 'face only' (defrost, or face and feet) the clicking stops. Do you have any insight to what this particular issue is? Any feedback is much appreciated.

@92813justin

4 жыл бұрын

Trevor Nolan if you can feel warm and cold air this is not your issue. The blend door actuator “blends” the warm and cold air to your preferred temperature.

@trevornolan846

4 жыл бұрын

CluEngineer well dang. Thanks for the feedback. do you know what else may cause a clicking/knocking noise that comes from behind the dash?

Great video thanks 😊 helpful

Which part number did you use (i have the same truck and problem) was it YH-1770 or YH-1881? Thanks

@92813justin

7 жыл бұрын

I went to the dealer and they gave me a part. I am sorry, but I do not remember the part number for this part.

My husbands truck blows cool air then all of a sudden it gets warm then goes back to cool air. No shift in temperature settings it does it all on its own. Will this fix that problem?? Let me add the air feels cool not cold. We added freon and it helped a little but the air keeps going back and forth from cool to warm.

This is the door that changes the temp from hot cold correct?

Did you have to pull the fuse to reset the position to align them both?

@92813justin

5 жыл бұрын

No, when I turned the truck on it reset it position. It is also keyed so it can only go in one way.

Did you use a open-ended wrench for the back screw. Great vid!

@92813justin

2 жыл бұрын

I used a socket

Great video by the way. I’m a little late to the party. But will they fix my air condition issue. Driver side blows cold air. Passenger side blows hot air. Thanks

@92813justin

4 жыл бұрын

Dual climate control is a different system

This works for even the limited f150? 2011 6.2

Thanks!