Why can’t I find a Speed Y all 1/2” all 3 ways??? I know I’ve seen them at the part houses but online none at all. Or y’all don’t make 1/2” all the way???

would it be as efficient to use the speed y on the end of the valve core removal tool and run both hoses to the pump? or is two individual valve core tools with one dedicated hose better?

Hello Appion , do you have an official distributor in EU please ? I can't find almost any of your products , not even the core remover tools .

@Appiontools

Жыл бұрын

Sorry for the confusion, please reach out to us directly at sales@appiontools.com

I would like to use a Y with a valve for my micron gauge which has two male 1/4" flares. Do you have one with a female down and one up? Three way valve would be fine but at least the upper female quick connect should have one. This would take a lot of potential leaks out of the two core remover setup. That would allow me to come off the 1/4 male on the core tool with an isolation valve to my micron gauge.

@Appiontools

2 жыл бұрын

no, we don't have anything like that at the moment. Currently, these are all of our Speed-Ys. More information on them can be found at appiontools.com/search.php?search_query=spdy§ion=product

Good vid. Do You Make a 1/2" -- 1/4" x 1/4" Y Fitting ?

@Appiontools

4 жыл бұрын

Unfortunately no, all of our Speed-Ys have (2) 3/8" male fittings

I can put this on the fieldpiece vp-85 correct? Vp85 has 1/2 inch and 3/8 inlet

@Appiontools

3 жыл бұрын

Yes these will work on any vacuum pump

Can you pull the other way attaching the 1/4 Y to the refrigerant port via a core removal tool? And the two 3/8 hoses to the vacuum pump? So I have 2 hoses on each port? Or would I not gain anything?

@Appiontools

Жыл бұрын

Yes, this will work and speed up your evacuation as long as your aren't exceeding the volume of the pump. So if you have a larger vacuum pump then this shouldn't be a problem. But when you start using multiple large diameter hoses with some of the smaller pump on the market then you will actually slow down your evacuation because you are exceeding the CFM capacity of the pump. For example the TEZ8 is an 8 CFM pump and can yield (4) 1/2in diameter hoses at once with no issues. But if you were to connect the same hoses to a smaller, lets say 3CFM pump, the vacuum pump will be overloaded and not yield the same benefits.

@vw_mods_4711

Жыл бұрын

@@Appiontools Cool many thanks for the reply, I will get one and give it a go, I have 8 cfm pump 👊👊

how can I buy T fitting

@joong2-RIDER

2 жыл бұрын

5/16x1/4

Why don’t you make a 1/4” 1/4” 1/4” Speed y ?? 😭😭😭 all my core tools megaflow hoses and vac pump connections Are 1/4”

@jpadgr8

2 жыл бұрын

1/4 is a small diameter for evacuation. Takes a long time to evacuate a system with a 1/4. Versus a 1/2 or 3/8. 🤔

@matthewking6509

2 жыл бұрын

@@jpadgr8 think about your line size and service port . Then get back to me …… hose size important yes the connection no . Would be minimal if at all noticed

@jpadgr8

2 жыл бұрын

@@matthewking6509 part number Appion SPDY 1/4…. 3/8 3/8 1/4. I’m not talking about line set ports etc. focus on ur question why don’t you make 1/4 1/4 1/4. Upgrade ur vacuum pump with 3/8 port 😆

@matthewking6509

2 жыл бұрын

@@jpadgr8 so go from a 1/4” out to a 3/8” out using an adaptor …. Pretty redundant ,

@jpadgr8

2 жыл бұрын

@@matthewking6509 🤦🏻‍♂️👀😆