8 Awesome 3D Prints That Will Blow Your Mind! 3D Printed on the Elegoo Neptune 4 MAX 3D Printer
Ойын-сауық
Here are 8 Cool 3D Printing models that you can print today! Check out todays video sponsor @ElegooOfficial Check out their affordable 3D Printers Here: bit.ly/3wej5rl
All these models can be found over on the @stlflix Website here: www.stlflix.com/
#3dprinting #3dprinter #3dprinted
Пікірлер: 57
Nice video. Would appreciate the list of 3d model names of the stl's from stlflix. Thanks
Well tuned printer. I come back to this channel from time to time. Relaxing experience - watching your timelapses sir.
@WildRoseBuilds
4 күн бұрын
Thanks for watching! I appreciate it
Aaahh, nothing like some 3D print and chill after a hard day!
@WildRoseBuilds
20 күн бұрын
Thanks for watching 🙏🏼
@axelhopfinger533
20 күн бұрын
@@WildRoseBuilds You keep making these quality videos, i'll keep watching . Deal?
The filament you used for the dragon is gorgeous
@WildRoseBuilds
20 күн бұрын
Yes!!! 3D Jake matte orange eco pla
I have to say that out of all of the 3D model printing channels you all have the best models, best music, and best time lapses. I wish I could put a bunch of your videos together and just have them in one long 2 hour block that I could put on when I am puttering around the house as they are awesome and soothing at the same time. One question for you on the incense burners as you have done a few - I printed one not too long ago that has a tiered shelving effect and it's awesome with the smoke flowing down with fluid (I'm excited to try some of your others). I put the metal washer in like you did on your various prints, and it sort of melted into the top of the print. That and there was an extra smell like the plastic was almost burning (it wasn't), but considering the metal disc was melting into the print something clearly was happening that was sub-par. I wanted to see if you ran into either of those scenarios and if you did what you did to potentially address them. Please keep up the excellent work.
@WildRoseBuilds
20 күн бұрын
Thanks for the kind words!! I usually pull the incense cones off before they fully burn down. I think the down draft cones tend to leave a little residue that has a weird smell. Maybe some left over oils or something. Petg would probably hold up better but I haven’t had any of these melt yet 😉
Everyone is wondering what kind if filament, software, and settings this person is using. I'm just wondering how they made a time laps without showing the filament extruder.
For the dragon skull that you put the light bulb into would it work better with leds for weight and a cleaner wall hang look?
How do I get my supports to come off like that?!?!?
Can you do a video on what software you use and the settings becuase those prints look incredible!
Nicely done, that is dope. What are the smoke things that you use?
A really interesting collection of prints. Love the laminar flow incense. Cool stuff.
Ummm where can i find those stl files and what was that glue uou used
What infill type do you use for the prints? Im still quite new to FDM pronting and just use gyroid.
@WildRoseBuilds
20 күн бұрын
I use supportive cubic. Lets you use less density while still being able to print internal overhangs!
@ChristopherPBacon69
20 күн бұрын
@@WildRoseBuildsamazing thank you! It looks like it will save a lot of time and filament!
What are those scented smoking little bullets called?
What type of fillament you used for the horns of the dragon? That looked amazing.
@WildRoseBuilds
20 күн бұрын
That was clear amz3d pla. Turned out really cool!
Fellow Albertan? This is really impressive, thanks for sharing!
Still the time lapse king, has the extruder been sorted after the initial leaks and problems?
The incense model is nice BUT how is it that the material doesn't melt from the heat of the incense? Cause I've tried to make my own looking like a Dino Graveyard using this Technique with the washer. But the material melted from the heat of the incense and the washer. Like a hot knife
tell me what kind of candles these are?
@WildRoseBuilds
20 күн бұрын
These are down draft incense cones!
How awesome 😍😍
whats your support settings ?
@WildRoseBuilds
20 күн бұрын
.15mm contact ✨
Disappointed Joel. No dice tower? Not good. My favourite was definitely the dragon lamp ✌️
@WildRoseBuilds
20 күн бұрын
More dice towers to come do t you worry haha! Thanks for watching
You could make a video with gift ideas for Mother's Day.
Will you one day make designs for consoles or PC towers?
@WildRoseBuilds
20 күн бұрын
I hope so!
The only thing mind blowing was the editing to remove the print head.
I love how those prints look finished, the only thing I'm looking a bit concerned is that I'm more into practical parts, I love to see someone rebuild an angle grinder part, a cover/carter from a scooter that is missing, pannels and door handles for cars and stuff like that, practical building, or even more industrial use like vaccuum tunnels for parts, gears for line feeders, all stuff that I mostly consider. More the use of chlorine and fluorine addition into materials for chemistry put into filters screws that don't crack under heat and corosive ambients, or self lubricant parts like sliders, wheels, gears, and so on.
@Solobusn
15 күн бұрын
You can definitely print some of those items ideally in a stronger material. I designed and printed a pool skimmer flap in petg and it’s being used in a chlorine pool for the past 3-4 years. It’s still holding strong. The material used will depend on environment and use case. I mainly follow designers that do functional parts in 3d printing.
Cutting holes with a soldering iron is the strangest thing here. Could just edit it intead of breathing fumes and covering the iron in plastic soot
that dragon 8:38 was really disappointing, you could have sliced the holes easily in slicer app before and printed with the holes
@WildRoseBuilds
20 күн бұрын
Totally! I didn’t have the idea to put lights in it until it was already printed. I will revisit that one for sure. No infill, more walls to block light, and a proper bulb mount. Thanks for watching!
Ouch, what did you do to your thumb?
@WildRoseBuilds
20 күн бұрын
Tried to grab a stick out of my dogs mouth 🥲
A flagon with a dragon...
Bonjour 🇨🇵 👏👏👏👏👍🏆🥂🎆🙏
Your finger
@WildRoseBuilds
20 күн бұрын
Dog bit it during fetch 😅
No more free model links?! Unsubscribed
@Mr.Rad1cal
16 күн бұрын
Poor.
@Kodiakbuteggdftt
13 күн бұрын
@@Mr.Rad1calsad
@durrellbowden5495
12 күн бұрын
@@Mr.Rad1cal🤣
@HunterEklund-yr4wh
11 күн бұрын
Didn't ask
Really? Subscription? 👎
@forteandblues
15 күн бұрын
You don’t have to be a dick.
@3dprintingnerd