Great video guys gyeon is my go to product I love love gyeon #1

Like always, perfect explain and show 👍👍👍👍the best team. Regards from Germany.

Excellent video, I can't believe how much I neglect my door shuts!

@GYEON_official

Жыл бұрын

It’s never too late to tackle them. ;) Regards, Y.

For severely dirty cars a second foam step can be a big help, too.

@GYEON_official

Жыл бұрын

Absolutely! And after a second one, a third one with Q²M Restart and then start your wash process. Regards, Y.

@danhiriscau1279

Жыл бұрын

@@GYEON_official Gyeon restart ist the best shampoo, i like it a lot. 👍

I learned a lot from the video with Sreten and all just started to click. I am studying these and am about to apply them straight away, step by step. A couple of contemplation (overthinking) of a learning noob: 1) When you take off the wheels, how does it affect their proper alignment? 2) I had a bad experience with the door shuts rinse - the moist stuck inside and it was hard to let the interior dry for couple of days How do you work out with a wet interior then?

@GYEON_official

Жыл бұрын

Hi Jan, 1) Removing wheels off the car doesn’t influence the alignment of your car nor the balancing of your wheel/tyre. 2) Always work with low water pressure and alongside the body panel to minimize splashing. Open the door at maximum angle to avoid unnecessary wish-plash. Ensure proper drying with microfiber and help of compressed air.

Absolutely love Bug & Grime remover, if the car isn’t too dirty I usually spray it on then give it a “spritz” with the hose as well after it’s had a minute or two, works really well as a pre-rinse step. Noticed in this video you didn’t rinse off the Bug & Grime remover but went straight over it with the foam - is that right? Will have to give that a try.

@GYEON_official

Жыл бұрын

Yes, this makes sure it doesn’t dry out as your foam gun also gives you water and on top you have some extra dwelling time together with the foam. Worth a try. Regards, Y.

@GYEON_official

Жыл бұрын

Yes you can. Y.

Couple of questions, for wheels would a Attachment used in a cordless drill be too much, the softest of bristles is what I am aiming for, have a bit of a dexterity issue, they are stock wheels nothing glossy. Also wouldn't a pressure washer rinse be too much on the body? I know you have to be careful with the edges of the PPF, but wouldn't the product remaining foam up too much in the seams/shut lines etc? Or with this being a prewash it's not too critical?

Is the APC suitable to be used with a ceramic coated car? Will it affect the ceramic detailer or Cure top up layer?

RD Present!!

Hi guru! I've got 2 questions: 1. For a pre-soak of the bottom panels, what would be better: Bug & Grime or APC (1:5)? 2. If I mix APC 1:5 and have the mixture remaining after the wash, for how long can I keep the mixture for any future use?

@GYEON_official

Жыл бұрын

1. Depends the type of dirt. For tar deposits both will not be effective so use according the type of cleaning you need to do. 2. Long enough, for sure till a next wash. Regards, Y.

@AdilKhan-by9wm

Жыл бұрын

@GYEON 1. IType of dirt is only dust / road grime and traffic film accumulated over a week.

Hi I’m new to detailing and am unsure of the process as in washing, clay bar then what after that??

@Theseones

Жыл бұрын

Claybar is the last step of detailing, afterwards one must polish those tiny scrathes away.

@daveallsopp320

Жыл бұрын

Do I need to wash lube residue off panels before polishing

@Theseones

Жыл бұрын

@@daveallsopp320 it is a good idea, also one final wash after polishing or atleast using something like Prep

@GYEON_official

Жыл бұрын

We made a lot of video’s which might be very helpful. But the moment you use a claybar the next step should be polishing. Regards, Y.

Hi! For a lightly dirty car with a 700ml foamer bottle, how much Gyeon Foam can I use? 30? 50ml?

@Theseones

Жыл бұрын

You can dilute it from 1:5 to 1:15, depending on how dirty the car is.

@yarinsheiman7789

Жыл бұрын

@@Theseones thanks!

@orthodox1717

Жыл бұрын

4% PIR

Hi