Very detailed video! Actually showing how C-clips are held in...I am keeping it for when I do the bearings/seals replacement. Thx for posting it!

@Autoenginecheck

2 жыл бұрын

Thanks FOR comment sir

Just incase someone watching this doesn't know DO NOT let your calipers hang by the brake line like you see in the video unless you want to replace the line

@Autoenginecheck

3 жыл бұрын

Thanks for your advice sir

@ekhlasbepari2965

3 жыл бұрын

good work

@loganspargo9222

3 жыл бұрын

. you probably know this already but if you don't.... brake lines are strong since they under a considerable amount of pressure doing that once may not do much but doing it multiple times will put stress on the line right where it goes into the metal fitting amd they will pop your brakes work on a hydraulic system which means the whole system relies on high pressure to work properly if that seal is broke anywhere in the system the whole thing will lose pressure and fail which could be catastrophic and potentially lethally if it happens while youre driving you dont want to take any chances with it

@David-ry5il

3 жыл бұрын

@@Autoenginecheck Its not as much the line cannot hole the weight it is how it hangs , look at how to kinks the line or folds it over this can damage the line and cause premature failure. It might not leak today Some might say if it does leak then it needed to be replaced. I have seen new lines get bumped the swinging weight was enough to cause the line to fail. This is especially the case on older cars, if you cannot get the line quickly this can mean the vehicle is down for several days waiting for a part. a piece of strong wire bent into an s shaped hanger best to have 4 in your box. or use zip ties. I like the wire hangers.

@spacecoastkid5033

Жыл бұрын

Hackerville. This is why I prefer to do as much repair with as I can. You just never know what these people are doing. Might not cause an immediate leak, but could cause a premature failure at some point.

Left out probably the hardest part. Getting the old bearings out. 😫

Thank you for the detailed video!

@Autoenginecheck

4 ай бұрын

Thanks for comment sir

This is the best video I ever seen step by step

@Autoenginecheck

3 жыл бұрын

thank you so Mach Sir

@nandojuarez6182

2 жыл бұрын

E

Will the size of the beatins mater between 8.5 and 9.25 will they work the same

I would've packed the bearings.

Thank u for this video amazing

@Autoenginecheck

Жыл бұрын

Thanks FOR comment sir

I have never seen someone put the bearings in dry.

what kit do you recommend?

After you remove the axles in the rear diff should you put the pin back in to keep the small gears on the top and bottom from falling out? I’ve seen them fall out in a few other videos and everyone says they are a pain to get back in

@Autoenginecheck

2 жыл бұрын

It is not good to re-apply after opening the axle lock or the small gear may go off later Although it can be attached later, it is better to keep the pin attached thanks FOR comment sir

@WildwindGamingMore

Жыл бұрын

bro they are a pain it took me days to figure out how to get them back in right there are no how too vids DO NOT DROP THEM

@johnsn10

Жыл бұрын

@@WildwindGamingMore I did this job a couple weeks ago I ended up holding the gears while I popped the c clips out and then I put the pin back in while I was working on it. Everything worked out great no problems

if you dont lightly greese the bearing it will be dry too long till fluid gets to it

@Autoenginecheck

2 жыл бұрын

Yes Sir you are right

they should have done the pin the same way on the front dif lmao

@Autoenginecheck

Жыл бұрын

yes sir

ভাই আপনি কি বাংলাদেশের,,আর আপনি কোথায় আছেন,, কই থেকে ভিডিও করছেন..?

@Autoenginecheck

3 жыл бұрын

Hmmm ami Bangladeshi Abu Dhabi musaffa thaki

Abdulwaheed

I replaced mine but never messed with the differential. I don’t seee why you would need to even touch that

@scottcpan68

2 жыл бұрын

Not sure the type of rear you were working on, but this is a Chrysler 9.25" which uses internal C clips to secure the axles. If you look closely at 11:30 you can see the clips going back in.

So you used a dirty piece of rebar shoved through the differential to the opposite side to use to get the bearing and seal removed instead of buying the proper tool. Definitely don't use this shop! 😮

@Autoenginecheck

Жыл бұрын

Dirty rod but later cleaned it with petrol sir

Are u speaking gibberish lmao

@Autoenginecheck

6 ай бұрын

Thanks for comment sir