Пікірлер

• 
  @Stancegang243 сағат бұрын

  Flame thrower! 🔥🔥🔥🔥

• 
  @svenjohanson60907 сағат бұрын

  Owns a Chevy Van G20 myself. 10 years ago I unfortunately had a crank bearing failure. I lifted the engine out through thel right door............it's much easier. Of course, you must remove the dashboard and the console that sits at the front of the engine where the AC compressor, servo and generator are mounted.

• 
  @joshtonry429110 сағат бұрын

  Get some brother. Looking good

• 
  @betweenthesharksgarage8 сағат бұрын

  workin hard at it

• 
  @krnsssdz11 сағат бұрын

  Please use ppe when dispersing defoliants. Atleast longsleeved shirt&gloves. those things are somewhat toxic.. Nice update on the yard situation!

• 
  @betweenthesharksgarage8 сағат бұрын

  fair point.. had the gloves but could have done better

• 
  @TopCat202112 сағат бұрын

  Look at the active ingredients look for 2-4-D for broadleaf control and roundup (glyphosate) for total eradication also strong vinegar >20 salt solution works for knockdown adding dish detergent to the mix helps th herbicide to stick to the plants. Good luck

• 
  @betweenthesharksgarage8 сағат бұрын

  thats the second nod for vinegar... i might give ita whirl cant hurt

• 
  @willtay301621 сағат бұрын

  That was a 25 min video to say I cut the front off a old push mower lmao

• 
  @betweenthesharksgarage9 сағат бұрын

  25 action packed minutes

• 
  @VikingShipExplorerКүн бұрын

  On my acreage I've needed a brush hog to knock down a type of thistle that is slowly taking over the the edges of the yard and it seems to creep in farther each year. In the last 10 years it's taken over about 3 feet of grass around the yard and showing no signs of ever stopping. I have a 60 inch mower deck that will have a 24HP engine mounted to it and I can push it from the front of my garden tractor. Need a few more pieces made and I'll be able to start building. I will also take an old mower and cut the front out as you did to sneak under the barbed wire fencing. Keep the kool videos coming.

• 
  @betweenthesharksgarage23 сағат бұрын

  thanks man, i have a mower deck or two laying around your plan sounds pretty useful and 24 hp is a lot!

• 
  @VikingShipExplorer22 сағат бұрын

  @@betweenthesharksgarage The stems of this brush are about the size of a straw and tuff and very close together and about 2 feet tall. I hope 24 HP will be enough....lol.

• 
  @jerald307Күн бұрын

  I use RM43 from tractor supply. I have the best results by applying herbicides & insecticides in the late afternoon or better yet in the early evening. This allows the treatments to penetrate the effected area slower without risk of midday sun & heat drying up or evaporating these expensive chemicals. Good luck taming that jungle.!! 🚜💨

• 
  @betweenthesharksgarage23 сағат бұрын

  I appreciate the tip, maybe i ll order some we are tractor supply deficient around here

• 
  @terrykyte1845Күн бұрын

  HAYWIRE FOR SURE

• 
  @RuststoredКүн бұрын

  What a mess!! If it wasn't for the hidden walls Id say try a flail mower

• 
  @betweenthesharksgarage23 сағат бұрын

  i had the same thought... l think i am just gonna have to tough it out once to find out what is under there

• 
  @scottfoster2487Күн бұрын

  You need to do another treatment with each over every spray on the whol place ,You have to get a few to really get into the main mother root system.

• 
  @lakepipes52Күн бұрын

  Nice job Ryan, there is definitely a huge indent into the overgrowth. Unfortunately the only way to deal with the wisteria is to chop it down. You were 100% right when you said to cut the trunk of the wisteria and hit it with herbicide. 👍👍

• 
  @betweenthesharksgarage8 сағат бұрын

  it helped a little but yea man... we have our work cut out for us no pun intended

• 
  @blackbartbartholomew7122Күн бұрын

  You should use a product called “Crossbow” you also need to add what they call a “Sticker” which helps the Crossbow not to be washed off. Also the slower the kill the better.

• 
  @suttonbogedain5874Күн бұрын

  Napalm since it did wonders for Vietnam. Hey, it's 4 am and I'm short of sleep and coffee. Struggling along side you, my brother.

• 
  @iscariotprojectКүн бұрын

  landscaping must be a killer business in that area people probably give up and pay for someone else to do it

• 
  @mh-ve9nv2 күн бұрын

  use this , RM43 total vegetation control . You can get it at tractor supply . itrs expensive but it works

• 
  @gengische2 күн бұрын

  Spray diesel on the leaves, not on the ground, it will clear enough to allow you to see what to chainsaw

• 
  @betweenthesharksgarage2 күн бұрын

  I have heard that before

• 
  @christopherburns41072 күн бұрын

  I got my stuff from tractor supply.. had ivy and other stuff growing sprayed it on a hot day took effect withing 3 days .. I let my dad borrow it can't remember what brand nothing you see everyday

• 
  @betweenthesharksgarage2 күн бұрын

  I ll check tractor supplies website thanks

• 
  @christopherburns41072 күн бұрын

  @@betweenthesharksgarage rm 43

• 
  @mbox3142 күн бұрын

  I applied alot of herbicide when I volunteered for a museum. I found that strong mixtures are not more effective and waste chemicals. Tryclophr is marketed as posion ivy and woody brush killer,it is more expensive than gylphosate and should be used on everything that isn't grass. Gylphosate is good for grass and pretty wesk on everything else. There are alternatives to gylphosate and they don't seem to work for beans.

• 
  @betweenthesharksgarage2 күн бұрын

  Thanks for that info. I am new to this

• 
  @mbox314Күн бұрын

  Your channel is neat AF. Keep up with the interesting and informative videos.

• 
  @paullester64422 күн бұрын

  Plz don't scrap the bead breaker even if it. Doesn't work i have one like it that the one little side peice broke it belonged to my great grandfather and I would buy yours if you go to get rid of it man

• 
  @mattewiegand98962 күн бұрын

  I feel this clean up so much. The house I'm in had older horders living in it, lovely people but man did they leave a lot to clean up. The yard has been so hard to get cleaned up.

• 
  @stillwaiting4352 күн бұрын

  🎉

• 
  @renamon19832 күн бұрын

  Thats a plastic "pulsa jet" carburetor. Dont tighten the bolts that hold it down too much or it warps the plastic and causes it to leak fuel past the diaphragm and into the engine causing it to run stupid rich, also auto parts stores sometimes have those diaphragms in stock. Also that run away was the cooling fan wind based governor that uses a paddle under the housing that gets pushed by the wind the cooling fan makes, along with springs and leaver arms to open and shut the throttle based on the load on the engine to maintain the peak power running RPM.

• 
  @betweenthesharksgarage2 күн бұрын

  Thanks for the info!

• 
  @jayhint44182 күн бұрын

  I like the videos but it would be great to see more work less talk

• 
  @betweenthesharksgarage2 күн бұрын

  Fair enough thanks for watching

• 
  @LifewithJames3 күн бұрын

  I’d suggest cutting the discharge opening larger so it doesn’t clog but you will need to make a wider safety guard/cover.

• 
  @suttonbogedain58743 күн бұрын

  loved it . Cobble away.

• 
  @betweenthesharksgarage2 күн бұрын

  Thanks man

• 
  @jamesshonk5654 күн бұрын

  Given a thought to the water pump might be going bad? I have ran across a case where the impelor on the pump was going bad and the car would over heat at times.

• 
  @brianalbee41534 күн бұрын

  Looking good

• 
  @mschinadollar5 күн бұрын

  What company did you buy from?

• 
  @Kyle-ev4fk6 күн бұрын

  I am not surprised by the running mower at all. You can't kill em. It's so silly that a person would buy more than one lawn mower in a lifetime.

• 
  @betweenthesharksgarage2 күн бұрын

  Man. I have killed a few… but I use them like an idiot

• 
  @rtz5496 күн бұрын

  I'd get a new and proper harmonic balancer and a correct timing pointer. Also verify #1 is at TDC. You could also at sometime put efi on it if you desired. Also get some rust converter and coat the underside of the van.

• 
  @rtz5496 күн бұрын

  Swival seats make a huge difference in having seating options for the back. You can make some using wheel bearing hubs. Consider painting or staining your wood tool box. You can get led lights for an rv to install as dome lights for when you want it fully bright. Also you can get a spare tire mount that goes into a 2" hitch receiver. If the trans goes out; just swap in a rebuilt one or consider doing a manual swap if you prefer that.

• 
  @rtz5496 күн бұрын

  Why didn't you pull the bumper?

• 
  @wiremunore3016 күн бұрын

  Awesome work

• 
  @betweenthesharksgarage6 күн бұрын

  Thank you! Cheers!

• 
  @scottfoster24877 күн бұрын

  Add some food coloring to the solution to be able to see were you have sprayed. Love the creative adaption.

• 
  @betweenthesharksgarage7 күн бұрын

  That’s a good idea

• 
  @mennoboon80378 күн бұрын

  Nice you got those working

• 
  @betweenthesharksgarage7 күн бұрын

  They have been really helpful

• 
  @mennoboon80378 күн бұрын

  I bet you wont use anything from whats there but guess wel see😅

• 
  @betweenthesharksgarage7 күн бұрын

  Man I am already using it. Waste not want not

• 
  @anthonycannavo89268 күн бұрын

  Hello. From Australia. I really enjoy your content. But looking at this problem with your yard. You can get a rake for your mini excavator. I have one on my mini, and it's awesome. Just a thought. Keep up the great work

• 
  @betweenthesharksgarage7 күн бұрын

  Thanks for watching and thanks for the tip. I have been looking at them. I am sure I will just keep adding accessories as we go

• 
  @bruceklassen82618 күн бұрын

  Loved the video, and how you fell in love again lol

• 
  @betweenthesharksgarage8 күн бұрын

  Thanks man. One day I ll find the source of the problem. Or it will truly fix itself… either way the jeep is awesome

• 
  @adamroberts58768 күн бұрын

  Go to a farm store for chemicals. Diesel fuel works too

• 
  @betweenthesharksgarage8 күн бұрын

  Good advice. I ll do an update on these eventually to see if they worked

• 
  @brodster_69978 күн бұрын

  We got to see that truck running the one that came with the house

• 
  @betweenthesharksgarage8 күн бұрын

  Stay tuned

• 
  @herbie20h9 күн бұрын

  Do I spy a 60 series landcruiser?

• 
  @betweenthesharksgarage8 күн бұрын

  Good eye. That’s a buddy’s truck

• 
  @bookworm67-hv7nm9 күн бұрын

  quick tip don't push it drag it saves on your back

• 
  @betweenthesharksgarage7 күн бұрын

  Fair point

• 
  @bookworm67-hv7nm9 күн бұрын

  not dumb i have a shoe lace holding up a quilt cover as a curtain as I have just moved into a new flat yes shoe lace is massive and it works while saving money for curtain poles on a budget here people doing my best with what i got

• 
  @betweenthesharksgarage8 күн бұрын

  Waste now want not right

• 
  @TylerCreates9 күн бұрын

  I am with you on not spraying death poison all over. I had some weed problems in my driveway and some Vinegar, soap, and water killed all of it. A quick search supposedly Vinegar will kill both the English and Poison Ivy with an extra couple treatments. Knowing what I know now I would not use standard Vinegar. I will be using the commercial strength Vinegar. The little bit of soap mixed in helps suspend the Vinegar on the leaves to burn them more. You can also do salt as well but I didn't like the idea of spraying salt all over. DON'T get the Vinegar spray on any metal.... Trust me. Anyhow just my experience with weed eating / mowing alternatives. Also all natural, the way it should be.

• 
  @betweenthesharksgarage7 күн бұрын

  I m happy to give it a whirl… so far my death poisons have not been particularly effective on the English ivy

• 
  @bookworm67-hv7nm9 күн бұрын

  iy's like watching some one hold a milkshake on a roller coaster🤣🤣🤣🤣🤣

• 
  @AJStarch9 күн бұрын

  Nothing dumb about that! Think about making a pivot mount on top of the mower hood so all you have to do is point and shoot. Plus it will up the MadMax factor! 🤣. I also loved Junkyard Wars and the UK version Scrapheap Challenge.

• 
  @betweenthesharksgarage7 күн бұрын

  Again with the lawnmower mod genius… that is why I would join your junkyard wars team any day

• 
  @bookworm67-hv7nm9 күн бұрын

  I like your brand of redneckery it's refreshing 🤣🤣🤣🤣 keep it up

• 
  @betweenthesharksgarage7 күн бұрын

  Redneckery abounds

• 
  @randiegadberry54489 күн бұрын

  I’m going to get one for my place. By the way, the Evolution saw is great!

• 
  @betweenthesharksgarage7 күн бұрын

  I love the sprayer and that saw

• 
  @mropel19 күн бұрын

  Datsun 720 4x4 😍