I think it would help save the diff cups if you dont wack the throttle back and forth repeatedly trying to flip the car over.
@xxdreamgamerxx20597 күн бұрын
What is the esc? 😮
@richardbrown676212 күн бұрын
You made it to fast to control didn't you 😮😅😅
@OmniMan_Racing12 күн бұрын
@@richardbrown6762 not on 3s. Easy to drive on 3s. 4s it's hard to put the power down
@happydayrc15 күн бұрын
Sorry friend if I rewrite you and I have another question and thanks for your answers it is nice to know that you have a friend on the other side of the world, Hello my friend first thank you for your video and your effort, I wanted to ask you something, answer if you have time. I have an ESC Hobbywings 120a model quicrun 10bl120g2. My question would be with the stock escap out 1 cable (4 color) but there is a plug with 3 colors on channel 2 and a second plug with 1 color (yellow) on channel 3. With hobby winds there is only one plug ( 3 cables). Where should I do that in? Channel 2? I am new and I don't know myself so well. Mille Grazie from Italy
@blargus653515 күн бұрын
Sick builds man! Tryna make a 100mph+ build, any tips?
@OmniMan_Racing15 күн бұрын
@@blargus6535 use the ak917 it's a more stable body. Add some fins to it . Highly recommend castle ESC over hobbywing for over 100mph, hobbywing cutoffs are too "safe". Get some good 1/10 foams and you should be good. Both of these cars are pretty much just rollers with electronics slapped in them, the ak917 has a little more work because of the dual motor conversion but outside of that nothing special done to the chassis or suspension
@DavidGarcia-zh9kh18 күн бұрын
How did you get the 40 series motor mount in there . I tried to install it and I need a 47 pinion to just get the gears to mesh . Which that gear is probably way to big
@OmniMan_Racing18 күн бұрын
@@DavidGarcia-zh9kh it's kinda a dumb mod. The car isn't fun over 2s anymore, gotta be too careful to enjoy it. I'm running a 45t pinion
@novamegaboxing970121 күн бұрын
tried a few different setups . I settled with 120amp quicrun esc 3660 3200 kv motor 19tooth pinon on 2s. .. currently running same times as 4x4 shortcourse at track and still wheelies .
@OmniMan_Racing21 күн бұрын
@@novamegaboxing9701 that's a good balanced setup. Even on 2s you'd have plenty of wheel speed
@novamegaboxing970121 күн бұрын
@@OmniMan_Racing knock on wood , haven't broken anything other than body dings...What motor are you running ?... I have the V1 sc8 combo sitting around been tempted to try the 4068 2700kv and bump pinon to 24t for the giggles. Idk if my 2s batteries can handle the draw tho.... Kinda want a 2nd to do the silly shizz y'all been doing running 4s. Wish someone would buggy conversion one . Seems it would do better than the old backslashes
@OmniMan_Racing21 күн бұрын
@@novamegaboxing9701 with the 40mm motors the smallest pinion you can go to is a 40t. It's not worth the swap. It's not fun having to be extra careful. I'm using a HobbyStar 4068 2650kv. Even on 2s my setup does over 45. Gets pretty hot even with fans and a heat sink
@novamegaboxing970121 күн бұрын
Why is the 40 tooth the smallest you can go ? Does the motor can hit the chassis braces?
@OmniMan_Racing20 күн бұрын
@@novamegaboxing9701 it's just how the adjustment on the 40 series mount is. Gotta push the fatter motor farther from the center shaft for clearance
@JesseBlum21 күн бұрын
Okay awesome can you let me know where you got those tires from because every pair I get anything over like once I hit 45 mph they just keep blowing up and I heard that these are the best tires to go. Right now I'm running a 4 to 6S lipo on here and it's just killer it's awesome
@MrMeDos22 күн бұрын
what did you have your steering rate on? Seem like it needs to be less than 50% EXP.. may 45 or 40. its really wiggly because its so much slop in the hubs and the steering assembly. i got mine up to 60mph and it flipped 8x and kept on moving.. they are built tough for sure.
@OmniMan_Racing21 күн бұрын
I think I had set the dual rate to like 35% on the steering. The problem was even with the wheelie bar and I could feed into it as slow as I wanted but the front wheels didn't stay on the ground. Can't steer if the wheels that steer are in the air 😅
@happydayrc22 күн бұрын
Super Video👍👍 🤜 This is a hobby that makes you walk a lot I know very well hello friend. I have a question to ask you one of these days indeed I do it immediately I also have a terminator Rlaarlo carbon version and I bought an esc the hobby wing quicrun wp 10 bl120 g2 120a if I mounted it and I would use it only with 3S lipo I should change also the engine? friend you don't have to answer me immediately without stress only when and if you can always hi from Rome Italy
@OmniMan_Racing22 күн бұрын
@@happydayrc stock motor will handle up to 4s with no problem
@happydayrc21 күн бұрын
@@OmniMan_Racing mille grazie amico👍👍
@Hungrybird47422 күн бұрын
Omni man makes em fast a f 👍. Thanks for sharing . Liking my regular granite a lot . Just widened it and what a difference in handling . I had them sitting for here for a month and would have done it sooner had I known it would make such a difference . It’s all stock besides that
@rc_michi25 күн бұрын
Good result! Nice bird sounds in the background 😅
@Multi-Skill-Bill25 күн бұрын
LOL! 72 eh? I run 5 inch tires on mine with stock electronics except receiver and the bigger pinion. Hits low 50's best guess. I am getting better with my controller settings, so control of the car is also getting better. But seriously, this thing is hard to control over 40ish. Mine is lowered with a rake and still rough to control. One thing I can say is this: The Omni Terminator can take a serious hit and drive away! Oh ya.. running 3s, 5500Mah 65c discharge too. See ya on the next one.
@SloppytoppyRC26 күн бұрын
What’s your set up bro
@OmniMan_Racing26 күн бұрын
@@SloppytoppyRC this was a 3300kv max10 80a combo. I no longer run this setup. Now I'm in a Hobbystar 4068 2650kv motor and castle Mamba Monster 2 ESC. I currently pull mid 50mph on only 2s
@Multi-Skill-BillАй бұрын
I run my Omni Terminator at 50+mph. The Granite is also cool. You can get them both near 75mph with the right tuning. (cheaply) 👍👍👍
@OmniMan_RacingАй бұрын
@@Multi-Skill-Bill 👍. My Omni-Terminator does 55 on 2s but it likes to eat the rear dog bones up. This little 1/18 granite should pull off about 80 on 4s once I get some good weather. My 1/10 Granites both do easy 110-115 on 3s. Look through my older videos
@Multi-Skill-Bill29 күн бұрын
@@OmniMan_Racing Yeah, I havent pushed mine any further. No real need where I am located. I lowered mine a good bit, so far, been lucky on the dogbones. Really hoping the aftermarket kicks up soon-ish. I saw your older vids as they came out. Diddnt sub til now tho. Just been a lurker hehe. See ya on the next one!
@micron3268Ай бұрын
Very nice! 4s is going to be interesting for sure!👍
@OmniMan_RacingАй бұрын
@@micron3268 I tried today but the pinion came loose at 62mph. Felt like it would have been 78-80mph ish
@KBASHRCАй бұрын
Good shit my brother..you the GRANITE KING. keep pushing it
@scaleworksRCАй бұрын
Yep, not too shabby! 👍
@OmniMan_RacingАй бұрын
@@scaleworksRC thanks I was surprised. It looked more like 50ish while I was out there
@scaleworksRCАй бұрын
@@OmniMan_Racing Yeah, the scale probably throws off the judgment but 50s is still damn fast for that scale imho
@happydayrcАй бұрын
Buogiorno friend I immediately subscribed to myself I wanted to wonder I have the carbon fiber version H put the biggest pigno that was in the box and it is 60kmh is normal?. hello thanks in advance. Greetings from Italy
@happydayrcАй бұрын
Hello my friend you know how can you activate the turbo button? Beautiful greetings from Italy
@happydayrcАй бұрын
Hello friend from Rome Italy, your videos have everything you need I have immediately subscribed to your channel are 616 I have only 11 if you can change the favor I would be grateful to you. Hello to the next time because I will definitely have questions about Omni Terminator. Hi buddy
@Danielxperez14Ай бұрын
Why not just do 4s esc and keep the stock motor? Lower kv is perfect for higher voltage
@OmniMan_RacingАй бұрын
I already had the electronics I swapped in and I didn't want to go high voltage to achieve more speed. I only really swapped the electronics out because the brakes on the stock ESC are horrible
@Danielxperez14Ай бұрын
So upgraded motor and 3s esc? I’ve seen people hit 45 just by changing the pinion, also some higher c eating batteries
@OmniMan_RacingАй бұрын
The current setup I have does over 50 on 2s
@Danielxperez14Ай бұрын
@@OmniMan_Racing straight gearing or how so fast?!
@OmniMan_RacingАй бұрын
@@Danielxperez14 1/8 motor. Did a 4068 size motor. 2650kv with a 45t pinion and stock 65t spur. Also using a Castle Creations Mamba Monster 2 6s ESC
@Danielxperez14Ай бұрын
@@OmniMan_Racing wow, 45 is pretty high lol and I’m over here still trying to convince myself to switch the 19t speed pinion they have me 😂
@OmniMan_RacingАй бұрын
@@Danielxperez14 with the motor mount for the 40mm motor you don't have the option to run anything smaller than a 40t pinion so you gotta go down a lot in kv if you want to run over 2s. The car has unusablepower now, causes more damage to itself making it less fun because you gotta be so easy on the throttle. Of all the setups I had the 3300kv hobbywing with the included speed pinion was my favorite
@JesseBlumАй бұрын
Well i dont know what you all are using but I have the 120a/esc im through 22/6s lipos 3300mah 80c, and well over 20 4s-120c-3300mah and ZERO issues. I find it hard to believe that its the esc, it seems like most of these videos are always from name brand thats catching fire? But I would give it another shot and use the new 2024 black v2 program card and check your settings. PWM is a huge one. It's why my first 120a by another company blew up
@OmniMan_RacingАй бұрын
This was before any updates they might have did. I still would never use a surpass ESC over any name brand ESC again.
@luissimoes8106Ай бұрын
WoW man...😬 What a Beast you got There 😎 I admire you Om.. Always Honest and Sincere, and Strait to Business... The Biggest Thuth about Rear wings was Said; finally. I don't know if it's an impression of mine... of my audition ...but it seems that has a tiny practically unpreceptble cooging in initial seconds but it just doesn't matter anyways. Can't wait to help you filming 😂😉
@yourfactstoryАй бұрын
how can you fit 8s on the aerotrooper?
@KBASHRCАй бұрын
Killer pass brother
@bradcarpenter1881Ай бұрын
Bro you went insane on this truck! That pinion is huge! I assume you are running the upgrade smaller gear center diff. I can't believe that speed and power is only 2S!
@OmniMan_RacingАй бұрын
Stock spur gear. I didn't go big on gearing for speed. That is literally what fit with the bigger 4068 brushless motor. I need to move to a low kv motor to slow the truck down a bit
@93jdmmikeАй бұрын
Nice work bud
@scaleworksRCАй бұрын
That TP motor sounds strong coming in, man. 🦾 Very impressive and respect to you for braving that heat AND the wind. It was brutal hot today!
@lyleburns2640Ай бұрын
Thats was a pretty good man keep it up and the truck looks good to
@Danielxperez14Ай бұрын
Wow…just wow…😂
@user-mz8uc9sc1oАй бұрын
Welches silikonöl hast du in diffs?
@PoweredByCastleАй бұрын
You're making that speed look easy! Mad props, can't wait to see what you hit next! 😎🏁"
@OmniMan_RacingАй бұрын
Much appreciated. Xlx2 makes everything look easy 😅
@M14armorerАй бұрын
Awesome pass bro!
@scaleworksRCАй бұрын
Yep, that brick is definitely worthy of the title "Beast" 😁👍
@OmniMan_RacingАй бұрын
Definitely deserves the title of Brick 🤣
@scaleworksRCАй бұрын
@@OmniMan_Racing You said it first 😁👍 That thing is badass bro
@OmniMan_RacingАй бұрын
@@scaleworksRC a lot working against me. Aerodynamics of a cinder block and it's a open wheel car running a low voltage setup
@scaleworksRCАй бұрын
@@OmniMan_Racing Oh yeah, that's definitely one of those "that car shouldn't be that fast" rigs for sure.. I'm honestly surprised it stayed on the ground 👍
@ThisisTyyАй бұрын
Also would you ever sell one of the shortend chassis you’ve been making?
@ThisisTyyАй бұрын
Aye I met you when I was visiting for Arrmageddon and seen you chillin by your car with a modelo and we talked for a bit about your car with the tamyia fiat body shit man I was gonna ask if you wanted to sesh cause I brought my hand blown rig an some hash with me but she wasn’t feeling good so had to dip out early
@OmniMan_RacingАй бұрын
Yeah you had the infraction 6s and I think I randomly said something to you 🤣 they were selling beer way too early. it was good meeting you out there. As for the chassis I'd have to make a couple more (which I plan to very soon) and put them through their paces. Next version will be a basher using a 6s Typhon as a base but this version was a limitless and I plan to continue speed running it.
@ThisisTyyАй бұрын
@@OmniMan_Racing yessir an hell yeah man haha and yeah keep on it those are super sick chassis’s and your gettin some crazy speeds on that setup an the others! The weather here in Washington sucks man I’m tryna go back to Florida again soon and rip some rc’s haha
@OmniMan_RacingАй бұрын
@@ThisisTyy hurricane season over here. Been making getting my speed runs in a task because I have to watch out for weather to cooperate, if it ain't rain it's wind. This build should end up pulling some sick numbers but it's a brick 🤣
@JLE006Ай бұрын
New to the Orlando area, is there any place worth running some offroad cars near by?
@OmniMan_RacingАй бұрын
@@JLE006 theres a track I believe called all out racing but I go to a park called South Port Park and run offroad
@laurahunt7511Ай бұрын
Im new to the hobby and i must say , i see a lot of foolish things being done , i mean i get what they're trying to prove because most of us will never do the things we see them doing but at least we get an idea on how hard to push vehicle
@OmniMan_RacingАй бұрын
Someone has to be the person that's dumb enough to test limits 🤣
@KBASHRCАй бұрын
Good 2s #..keep pushing it..
@speeedy_rcАй бұрын
Solid 2s pass!
@speeedy_rcАй бұрын
Really cool build! Want to see you open that thing up.
@OmniMan_RacingАй бұрын
Felt just like my 3s Granite while I was running it today on 2s and it was super stable. It's gonna put up some good numbers on 3s when I have the confidence and spare parts to make that run. I think parallel 2s should push it into the 90s on this gearing
@micron3268Ай бұрын
Nice 2s passes buddy!👍
@RC-Closer1313Ай бұрын
Damn bro… that xLx2 is as big as the truck😳.. lol. Just put the wheels on the esc..
@luissimoes8106Ай бұрын
Well Brother, You may not Trust that Beauty Monster but, as I told you, in a couple of months I will be able to help you ... Filming 😆😆😆 😉
@Mikey45013Ай бұрын
What motor esc combo do you have
@OmniMan_RacingАй бұрын
Hobbywing seaking 120a 6s ESC and a 3660 2700kv motor
@Mikey45013Ай бұрын
Do you run into issues with it getting hot? I was looking at the seaking 30a and seaking 2040 motor but wasn't sure if the factory cooling pickup would be enough. I only run 2s
@OmniMan_RacingАй бұрын
@@Mikey45013 I think that's too small for these boats. I honestly haven't ran this boat in over a year but on 3s I was doing mid 40s with no heat issues
@Mikey45013Ай бұрын
@@OmniMan_Racing thank you. I will look into the 120a then.
@marcospascualАй бұрын
Excelent video, thans a lot! Plese can you share the exact lenght for screws to be reaplaced? is it amazon M3 titanium screws ? is 10mm enough ? Thanks a lot!!!
@OmniMan_RacingАй бұрын
They are m3x25 screws. I'd look for hardened steel instead of titanium. To be honest I'd leave them alone if they haven't broken yet, once you make them harder you start bending the shock tower. It's cheaper and easier to replace screws than it is the whole shock tower
Пікірлер
I think it would help save the diff cups if you dont wack the throttle back and forth repeatedly trying to flip the car over.
What is the esc? 😮
You made it to fast to control didn't you 😮😅😅
@@richardbrown6762 not on 3s. Easy to drive on 3s. 4s it's hard to put the power down
Sorry friend if I rewrite you and I have another question and thanks for your answers it is nice to know that you have a friend on the other side of the world, Hello my friend first thank you for your video and your effort, I wanted to ask you something, answer if you have time. I have an ESC Hobbywings 120a model quicrun 10bl120g2. My question would be with the stock escap out 1 cable (4 color) but there is a plug with 3 colors on channel 2 and a second plug with 1 color (yellow) on channel 3. With hobby winds there is only one plug ( 3 cables). Where should I do that in? Channel 2? I am new and I don't know myself so well. Mille Grazie from Italy
Sick builds man! Tryna make a 100mph+ build, any tips?
@@blargus6535 use the ak917 it's a more stable body. Add some fins to it . Highly recommend castle ESC over hobbywing for over 100mph, hobbywing cutoffs are too "safe". Get some good 1/10 foams and you should be good. Both of these cars are pretty much just rollers with electronics slapped in them, the ak917 has a little more work because of the dual motor conversion but outside of that nothing special done to the chassis or suspension
How did you get the 40 series motor mount in there . I tried to install it and I need a 47 pinion to just get the gears to mesh . Which that gear is probably way to big
@@DavidGarcia-zh9kh it's kinda a dumb mod. The car isn't fun over 2s anymore, gotta be too careful to enjoy it. I'm running a 45t pinion
tried a few different setups . I settled with 120amp quicrun esc 3660 3200 kv motor 19tooth pinon on 2s. .. currently running same times as 4x4 shortcourse at track and still wheelies .
@@novamegaboxing9701 that's a good balanced setup. Even on 2s you'd have plenty of wheel speed
@@OmniMan_Racing knock on wood , haven't broken anything other than body dings...What motor are you running ?... I have the V1 sc8 combo sitting around been tempted to try the 4068 2700kv and bump pinon to 24t for the giggles. Idk if my 2s batteries can handle the draw tho.... Kinda want a 2nd to do the silly shizz y'all been doing running 4s. Wish someone would buggy conversion one . Seems it would do better than the old backslashes
@@novamegaboxing9701 with the 40mm motors the smallest pinion you can go to is a 40t. It's not worth the swap. It's not fun having to be extra careful. I'm using a HobbyStar 4068 2650kv. Even on 2s my setup does over 45. Gets pretty hot even with fans and a heat sink
Why is the 40 tooth the smallest you can go ? Does the motor can hit the chassis braces?
@@novamegaboxing9701 it's just how the adjustment on the 40 series mount is. Gotta push the fatter motor farther from the center shaft for clearance
Okay awesome can you let me know where you got those tires from because every pair I get anything over like once I hit 45 mph they just keep blowing up and I heard that these are the best tires to go. Right now I'm running a 4 to 6S lipo on here and it's just killer it's awesome
what did you have your steering rate on? Seem like it needs to be less than 50% EXP.. may 45 or 40. its really wiggly because its so much slop in the hubs and the steering assembly. i got mine up to 60mph and it flipped 8x and kept on moving.. they are built tough for sure.
I think I had set the dual rate to like 35% on the steering. The problem was even with the wheelie bar and I could feed into it as slow as I wanted but the front wheels didn't stay on the ground. Can't steer if the wheels that steer are in the air 😅
Super Video👍👍 🤜 This is a hobby that makes you walk a lot I know very well hello friend. I have a question to ask you one of these days indeed I do it immediately I also have a terminator Rlaarlo carbon version and I bought an esc the hobby wing quicrun wp 10 bl120 g2 120a if I mounted it and I would use it only with 3S lipo I should change also the engine? friend you don't have to answer me immediately without stress only when and if you can always hi from Rome Italy
@@happydayrc stock motor will handle up to 4s with no problem
@@OmniMan_Racing mille grazie amico👍👍
Omni man makes em fast a f 👍. Thanks for sharing . Liking my regular granite a lot . Just widened it and what a difference in handling . I had them sitting for here for a month and would have done it sooner had I known it would make such a difference . It’s all stock besides that
Good result! Nice bird sounds in the background 😅
LOL! 72 eh? I run 5 inch tires on mine with stock electronics except receiver and the bigger pinion. Hits low 50's best guess. I am getting better with my controller settings, so control of the car is also getting better. But seriously, this thing is hard to control over 40ish. Mine is lowered with a rake and still rough to control. One thing I can say is this: The Omni Terminator can take a serious hit and drive away! Oh ya.. running 3s, 5500Mah 65c discharge too. See ya on the next one.
What’s your set up bro
@@SloppytoppyRC this was a 3300kv max10 80a combo. I no longer run this setup. Now I'm in a Hobbystar 4068 2650kv motor and castle Mamba Monster 2 ESC. I currently pull mid 50mph on only 2s
I run my Omni Terminator at 50+mph. The Granite is also cool. You can get them both near 75mph with the right tuning. (cheaply) 👍👍👍
@@Multi-Skill-Bill 👍. My Omni-Terminator does 55 on 2s but it likes to eat the rear dog bones up. This little 1/18 granite should pull off about 80 on 4s once I get some good weather. My 1/10 Granites both do easy 110-115 on 3s. Look through my older videos
@@OmniMan_Racing Yeah, I havent pushed mine any further. No real need where I am located. I lowered mine a good bit, so far, been lucky on the dogbones. Really hoping the aftermarket kicks up soon-ish. I saw your older vids as they came out. Diddnt sub til now tho. Just been a lurker hehe. See ya on the next one!
Very nice! 4s is going to be interesting for sure!👍
@@micron3268 I tried today but the pinion came loose at 62mph. Felt like it would have been 78-80mph ish
Good shit my brother..you the GRANITE KING. keep pushing it
Yep, not too shabby! 👍
@@scaleworksRC thanks I was surprised. It looked more like 50ish while I was out there
@@OmniMan_Racing Yeah, the scale probably throws off the judgment but 50s is still damn fast for that scale imho
Buogiorno friend I immediately subscribed to myself I wanted to wonder I have the carbon fiber version H put the biggest pigno that was in the box and it is 60kmh is normal?. hello thanks in advance. Greetings from Italy
Hello my friend you know how can you activate the turbo button? Beautiful greetings from Italy
Hello friend from Rome Italy, your videos have everything you need I have immediately subscribed to your channel are 616 I have only 11 if you can change the favor I would be grateful to you. Hello to the next time because I will definitely have questions about Omni Terminator. Hi buddy
Why not just do 4s esc and keep the stock motor? Lower kv is perfect for higher voltage
I already had the electronics I swapped in and I didn't want to go high voltage to achieve more speed. I only really swapped the electronics out because the brakes on the stock ESC are horrible
So upgraded motor and 3s esc? I’ve seen people hit 45 just by changing the pinion, also some higher c eating batteries
The current setup I have does over 50 on 2s
@@OmniMan_Racing straight gearing or how so fast?!
@@Danielxperez14 1/8 motor. Did a 4068 size motor. 2650kv with a 45t pinion and stock 65t spur. Also using a Castle Creations Mamba Monster 2 6s ESC
@@OmniMan_Racing wow, 45 is pretty high lol and I’m over here still trying to convince myself to switch the 19t speed pinion they have me 😂
@@Danielxperez14 with the motor mount for the 40mm motor you don't have the option to run anything smaller than a 40t pinion so you gotta go down a lot in kv if you want to run over 2s. The car has unusablepower now, causes more damage to itself making it less fun because you gotta be so easy on the throttle. Of all the setups I had the 3300kv hobbywing with the included speed pinion was my favorite
Well i dont know what you all are using but I have the 120a/esc im through 22/6s lipos 3300mah 80c, and well over 20 4s-120c-3300mah and ZERO issues. I find it hard to believe that its the esc, it seems like most of these videos are always from name brand thats catching fire? But I would give it another shot and use the new 2024 black v2 program card and check your settings. PWM is a huge one. It's why my first 120a by another company blew up
This was before any updates they might have did. I still would never use a surpass ESC over any name brand ESC again.
WoW man...😬 What a Beast you got There 😎 I admire you Om.. Always Honest and Sincere, and Strait to Business... The Biggest Thuth about Rear wings was Said; finally. I don't know if it's an impression of mine... of my audition ...but it seems that has a tiny practically unpreceptble cooging in initial seconds but it just doesn't matter anyways. Can't wait to help you filming 😂😉
how can you fit 8s on the aerotrooper?
Killer pass brother
Bro you went insane on this truck! That pinion is huge! I assume you are running the upgrade smaller gear center diff. I can't believe that speed and power is only 2S!
Stock spur gear. I didn't go big on gearing for speed. That is literally what fit with the bigger 4068 brushless motor. I need to move to a low kv motor to slow the truck down a bit
Nice work bud
That TP motor sounds strong coming in, man. 🦾 Very impressive and respect to you for braving that heat AND the wind. It was brutal hot today!
Thats was a pretty good man keep it up and the truck looks good to
Wow…just wow…😂
Welches silikonöl hast du in diffs?
You're making that speed look easy! Mad props, can't wait to see what you hit next! 😎🏁"
Much appreciated. Xlx2 makes everything look easy 😅
Awesome pass bro!
Yep, that brick is definitely worthy of the title "Beast" 😁👍
Definitely deserves the title of Brick 🤣
@@OmniMan_Racing You said it first 😁👍 That thing is badass bro
@@scaleworksRC a lot working against me. Aerodynamics of a cinder block and it's a open wheel car running a low voltage setup
@@OmniMan_Racing Oh yeah, that's definitely one of those "that car shouldn't be that fast" rigs for sure.. I'm honestly surprised it stayed on the ground 👍
Also would you ever sell one of the shortend chassis you’ve been making?
Aye I met you when I was visiting for Arrmageddon and seen you chillin by your car with a modelo and we talked for a bit about your car with the tamyia fiat body shit man I was gonna ask if you wanted to sesh cause I brought my hand blown rig an some hash with me but she wasn’t feeling good so had to dip out early
Yeah you had the infraction 6s and I think I randomly said something to you 🤣 they were selling beer way too early. it was good meeting you out there. As for the chassis I'd have to make a couple more (which I plan to very soon) and put them through their paces. Next version will be a basher using a 6s Typhon as a base but this version was a limitless and I plan to continue speed running it.
@@OmniMan_Racing yessir an hell yeah man haha and yeah keep on it those are super sick chassis’s and your gettin some crazy speeds on that setup an the others! The weather here in Washington sucks man I’m tryna go back to Florida again soon and rip some rc’s haha
@@ThisisTyy hurricane season over here. Been making getting my speed runs in a task because I have to watch out for weather to cooperate, if it ain't rain it's wind. This build should end up pulling some sick numbers but it's a brick 🤣
New to the Orlando area, is there any place worth running some offroad cars near by?
@@JLE006 theres a track I believe called all out racing but I go to a park called South Port Park and run offroad
Im new to the hobby and i must say , i see a lot of foolish things being done , i mean i get what they're trying to prove because most of us will never do the things we see them doing but at least we get an idea on how hard to push vehicle
Someone has to be the person that's dumb enough to test limits 🤣
Good 2s #..keep pushing it..
Solid 2s pass!
Really cool build! Want to see you open that thing up.
Felt just like my 3s Granite while I was running it today on 2s and it was super stable. It's gonna put up some good numbers on 3s when I have the confidence and spare parts to make that run. I think parallel 2s should push it into the 90s on this gearing
Nice 2s passes buddy!👍
Damn bro… that xLx2 is as big as the truck😳.. lol. Just put the wheels on the esc..
Well Brother, You may not Trust that Beauty Monster but, as I told you, in a couple of months I will be able to help you ... Filming 😆😆😆 😉
What motor esc combo do you have
Hobbywing seaking 120a 6s ESC and a 3660 2700kv motor
Do you run into issues with it getting hot? I was looking at the seaking 30a and seaking 2040 motor but wasn't sure if the factory cooling pickup would be enough. I only run 2s
@@Mikey45013 I think that's too small for these boats. I honestly haven't ran this boat in over a year but on 3s I was doing mid 40s with no heat issues
@@OmniMan_Racing thank you. I will look into the 120a then.
Excelent video, thans a lot! Plese can you share the exact lenght for screws to be reaplaced? is it amazon M3 titanium screws ? is 10mm enough ? Thanks a lot!!!
They are m3x25 screws. I'd look for hardened steel instead of titanium. To be honest I'd leave them alone if they haven't broken yet, once you make them harder you start bending the shock tower. It's cheaper and easier to replace screws than it is the whole shock tower