Good result! Nice bird sounds in the background 😅

LOL! 72 eh? I run 5 inch tires on mine with stock electronics except receiver and the bigger pinion. Hits low 50's best guess. I am getting better with my controller settings, so control of the car is also getting better. But seriously, this thing is hard to control over 40ish. Mine is lowered with a rake and still rough to control. One thing I can say is this: The Omni Terminator can take a serious hit and drive away! Oh ya.. running 3s, 5500Mah 65c discharge too. See ya on the next one.

tried a few different setups . I settled with 120amp quicrun esc 3660 3200 kv motor 19tooth pinon on 2s. .. currently running same times as 4x4 shortcourse at track and still wheelies .

@OmniMan_Racing

21 күн бұрын

@@novamegaboxing9701 that's a good balanced setup. Even on 2s you'd have plenty of wheel speed

@novamegaboxing9701

21 күн бұрын

@@OmniMan_Racing knock on wood , haven't broken anything other than body dings...What motor are you running ?... I have the V1 sc8 combo sitting around been tempted to try the 4068 2700kv and bump pinon to 24t for the giggles. Idk if my 2s batteries can handle the draw tho.... Kinda want a 2nd to do the silly shizz y'all been doing running 4s. Wish someone would buggy conversion one . Seems it would do better than the old backslashes

@OmniMan_Racing

21 күн бұрын

@@novamegaboxing9701 with the 40mm motors the smallest pinion you can go to is a 40t. It's not worth the swap. It's not fun having to be extra careful. I'm using a HobbyStar 4068 2650kv. Even on 2s my setup does over 45. Gets pretty hot even with fans and a heat sink

@novamegaboxing9701

21 күн бұрын

Why is the 40 tooth the smallest you can go ? Does the motor can hit the chassis braces?

@OmniMan_Racing

20 күн бұрын

@@novamegaboxing9701 it's just how the adjustment on the 40 series mount is. Gotta push the fatter motor farther from the center shaft for clearance

Super Video👍👍 🤜 This is a hobby that makes you walk a lot I know very well hello friend. I have a question to ask you one of these days indeed I do it immediately I also have a terminator Rlaarlo carbon version and I bought an esc the hobby wing quicrun wp 10 bl120 g2 120a if I mounted it and I would use it only with 3S lipo I should change also the engine? friend you don't have to answer me immediately without stress only when and if you can always hi from Rome Italy

@OmniMan_Racing

22 күн бұрын

@@happydayrc stock motor will handle up to 4s with no problem

@happydayrc

21 күн бұрын

@@OmniMan_Racing mille grazie amico👍👍

what did you have your steering rate on? Seem like it needs to be less than 50% EXP.. may 45 or 40. its really wiggly because its so much slop in the hubs and the steering assembly. i got mine up to 60mph and it flipped 8x and kept on moving.. they are built tough for sure.

@OmniMan_Racing

21 күн бұрын

I think I had set the dual rate to like 35% on the steering. The problem was even with the wheelie bar and I could feed into it as slow as I wanted but the front wheels didn't stay on the ground. Can't steer if the wheels that steer are in the air 😅

Okay awesome can you let me know where you got those tires from because every pair I get anything over like once I hit 45 mph they just keep blowing up and I heard that these are the best tires to go. Right now I'm running a 4 to 6S lipo on here and it's just killer it's awesome