Пікірлер

• 
  @holliebower136716 сағат бұрын

  Hi! I’m seeing options for ordering an auto or manual actuator, which would I need to order?

• 
  @deliboyfilms5 күн бұрын

  what specifically were you turning on and off bc im trying to research for my specific deck

• 
  @diydevin5 күн бұрын

  It’s bypassing the parking brake wire. Usually you have to apply the parking brake to watch anything on the radio.

• 
  @user-pv7em9pm4w19 күн бұрын

  Is it needed to be calibrated?

• 
  @diydevin19 күн бұрын

  Yes and no, figure out what way the air is blowing, for example if it’s blowing at just your feet put the dial to the feet setting and then install the blend door actuator.

• 
  @user-pv7em9pm4w19 күн бұрын

  @@diydevin is air flow direction depend of blend door?

• 
  @diydevin19 күн бұрын

  Yes it is.

• 
  @WillieLumpLumper20 күн бұрын

  Hello, it doesn't work on my avh 2300 nex and my remote blue white wire out of head unit stopped working has 0 power and my bypass won't work because of it so now been searching for a fix to get my options un grayed so can setup new amps.

• 
  @diydevin19 күн бұрын

  I’m sorry to hear that, it’s worked on all my NEX models I have had. How old is your unit?

• 
  @patrickearle373221 күн бұрын

  Thanks for the video. I know it was a while ago but it is super clear and easily understood.

• 
  @diydevin21 күн бұрын

  I am glad it helped, thank you for the positive feedback.

• 
  @christianlatshaw1767Ай бұрын

  3800 nex doesnt work ma man. Still trying to find a bypass

• 
  @diydevinАй бұрын

  I’m sorry to hear that, you can try a parking brake bypass wiring kit. I got one a few years back on eBay.

• 
  @kelvinmackey9070Ай бұрын

  Will this work for 1500 nex?

• 
  @diydevinАй бұрын

  It should; it has worked for me on every NEX I have currently tried.

• 
  @kelvinmackey9070Ай бұрын

  What did you do for the park brake wire

• 
  @diydevinАй бұрын

  I grounded it; connected it to the black wire coming out of the radio.

• 
  @robertpimentel9972Ай бұрын

  Could a intermittent ac not working be a possibility for this failed part? I recently changed ac compressor and did a proper recover and charge on Freon. It was working great and randomly began blowing hot air, the next day it was back to blowing cold air, again intermittently going hot

• 
  @diydevinАй бұрын

  Yes that could very easily be the case. If the blend door actuator isn’t closing or opening properly then you can have inconsistent temperature through the vents.

• 
  @christopherfaeth8047Ай бұрын

  Thank you!!!

• 
  @diydevinАй бұрын

  You're welcome! Glad it helped.

• 
  @AbeC116Ай бұрын

  I did that won’t show what’s on my phone to my screen videos

• 
  @diydevinАй бұрын

  I’m sorry to hear that. This is specifically to watch DVDs and or videos from a flash drive. I personally have not tried from a phone.

• 
  @AbeC116Ай бұрын

  Oh ok then if you figure out how to watch KZread or music videos please let me know I would really appreciate it thanks

• 
  @diydevinАй бұрын

  I’ve seen some people use a magic box to do that. I haven’t tried it but it might be worth it for you.

• 
  @johnnycortez46Ай бұрын

  My AC is blowing through defrost on my 2006 6.0. Besides a vacuum leak. Can this be a potential problem for that?

• 
  @diydevinАй бұрын

  Yes, very likely! That is what this truck was doing before I changed it. Make sure to have your dial turned to defrost before changing it otherwise it will mess up your controls.

• 
  @johnnycortez46Ай бұрын

  @diydevin Ok awesome. I'll order a OEM replacement and give it a shot. Thanks for replying

• 
  @user-jc6dt9yj4wАй бұрын

  Liar!! You can’t remove the shield without unplugging the cord? 😢

• 
  @diydevinАй бұрын

  We are sorry you feel that way. I’m going to quote from the video “make sure you unplug that sensor” at 2:09

• 
  @jordimartorell92482 ай бұрын

  Is this also for the 1999 Ford Expedition??

• 
  @diydevin2 ай бұрын

  It is not, unfortunately the actuator on the expedition of that year is under the center dash rather than behind the glove box.

• 
  @jordimartorell92482 ай бұрын

  @@diydevin Thank you

• 
  @mikemoler349Ай бұрын

  What were your symptoms making you replace this?

• 
  @jordimartorell9248Ай бұрын

  @mikemoler349 well although I changed to AC, it keeps blowing hot air, and now it does not blow any air except defrost in front counsel

• 
  @jordimartorell9248Ай бұрын

  @@mikemoler349 Back counsel if fine no issues

• 
  @Schmeefinstein2 ай бұрын

  Works on my avh-w4500nex. Thanks!!

• 
  @diydevin2 ай бұрын

  Glad to hear! Enjoy the freedom.

• 
  @540twisted2 ай бұрын

  Anyone try replacing it from underneath?

• 
  @diydevin2 ай бұрын

  I personally did and it would work but it was way harder to see what you were doing. If you had a camera so you could see what you were doing; then doing it from underneath would possibly be easier.

• 
  @540twisted2 ай бұрын

  @@diydevin okay thanks Dev

• 
  @tylerbridges60312 ай бұрын

  Does it bypass it so that you can alter the greyed out settings? Trying to figure out how to alter the dimmer/illumination settings without having to adjust my wiring.

• 
  @diydevin2 ай бұрын

  I believe so, I don’t remember having any greyed out settings after doing it. I don’t have that truck anymore or else I would check right now. I will see if I can get ahold of the guy I sold it too and check if possible.

• 
  @Chizaveli2 ай бұрын

  I just did it lmao good shit bro

• 
  @diydevin2 ай бұрын

  Glad it helped! Originally made this video to help a friend out and it ended up helping thousands out.

• 
  @berniemackattack8628 күн бұрын

  What model do you have? I'm interested in getting the AVH-521ex .

• 
  @diydevin27 күн бұрын

  The one in the video is a 6400NEX, but I have also had the 2500NEX, 2550NEX, 6500NEX and my most recent radio is the 8500NEX that has been my favorite so far.

• 
  @williamhamblin47392 ай бұрын

  thanks a lot very informational

• 
  @diydevin2 ай бұрын

  Glad it was helpful! Thank you for the positive feedback.

• 
  @SAGE1VIGOR3 ай бұрын

  Tried it on 3 different pioneer stereos. Reset them And retried. DOES NOT WORK.

• 
  @diydevin3 ай бұрын

  I am sorry this trick did not work for you, it has worked on all my pioneer radios I personally have as well as hundreds of others I have received feedback from.

• 
  @robertclymer69484 ай бұрын

  Thanks Brother for the video. It is funny, that the Can you installed has in the "IN" hose going to the 90Deg Valve cover Pvc connector, but the J&L can option in your link has the Out Line going to the Pvc 90 deg connector. Weird. I hooked up a cheaper version on my 2.7L, Without the 45 and 90 deg connectors already installed and my Truck would not run right Idling at 2500 rpm with the Pvc hose to in the "IN" on can and the "Out" hose to the Intake manifold.

• 
  @diydevin4 ай бұрын

  That is interesting, My brother has the J&L I will have to take a look at it. You can always swap the in and out and see if it changes anything, but it honestly shouldn't make a difference. Either way it's still going to be filtered. I think it's mainly labeled so that people can easily install it. I have put about 20,000 on mine and the only time its had a rough idle was when it was -10 outside.

• 
  @abeshelby33844 ай бұрын

  Hey brother, so i got a 2018 raptor with 120k miles , got engine light for code p0420 catalytic bank 1 , BUT i can tell oil leak from stuck piston rings messed the catalytic. IF i install a catch can, and do a good oil change with good additives ,would catch Can Help ? Should i do that first and then see if i still need to replace Catalytic? Thanks and God Bless

• 
  @diydevin4 ай бұрын

  It would probably help since it pulls out all the junk from the blow by that normally would get combusted again and then run into the catalytic converter.

• 
  @AlexPtc894 ай бұрын

  Cars do 400 000 kms with no such thing. Pay more attention to maintenance and less attention to these moronic mods

• 
  @diydevin4 ай бұрын

  Yes and no, one of the biggest issues with the first generation Ecoboost is build up on the intake valves. This can be fixed by installing an oil separator.

• 
  @noahkidd46744 ай бұрын

  Thanks! This helped, hopefully that pesky message stays away! It has so far. 🤞🏻

• 
  @diydevin4 ай бұрын

  Awesome, glad it helped!

• 
  @diydevin4 ай бұрын

  @1johnnyangel J&L makes one for the 2001 Tacoma and 4runner.

• 
  @1johnnyangel4 ай бұрын

  So.... an oil filter? 😂😂😂😂

• 
  @diydevin4 ай бұрын

  One filters, and one separates. Oil filters take dirt particles and other foreign contaminants and filters it out. Oil separator separates oil from the air of blow-by that’s created during combustion.

• 
  @1johnnyangel4 ай бұрын

  @@diydevin why can't I find this for my 2001 tacoma

• 
  @THEDADDY77705 ай бұрын

  Why wouldn't you just use it to pay off you shopping..

• 
  @diydevin5 ай бұрын

  You can but then you miss out on 2-4% of whatever your cash back for the year was.

• 
  @ThatRascalMerlin5 ай бұрын

  Couldnt get it to work 2550 Nex

• 
  @diydevin5 ай бұрын

  Sorry to hear that, you might have to get a bypass wiring kit from Amazon. It will accomplish the same thing just a little more work.

• 
  @ThatRascalMerlin5 ай бұрын

  @@diydevin My installer left the thin green wire in a loop from the brake sensor input to the ground. Could that be causing this? Do I need to cut the wire? Or remove it from the back of the head unit altogether?

• 
  @diydevin5 ай бұрын

  @@ThatRascalMerlin Thats one of 3 wires you will have to use, the bypass kit will hook together the parking brake wire, ground wire and the power wire so it's bypassed. In some cases it will use 4 of the radio wires. Your installer might be able to sell you one as well.

• 
  @ThatRascalMerlin5 ай бұрын

  @@diydevin So, the wire has nothing to do with whether your hack will work? Also, my software is the latest, 18.11 if that helps

• 
  @diydevin5 ай бұрын

  @@ThatRascalMerlin Correct, it seems like some models it doesn't work on for whatever reason.

• 
  @operationhotshotinc.68875 ай бұрын

  How’s it saving you money by cashing out if you’re going to shop at Costco anyway and spend the money? Lol it’s a good hack if you NEED the cash but to not SAVE money

• 
  @diydevin5 ай бұрын

  Most people use a credit card at Costco and that gives you more cash back. By cashing it out and using a credit card you’re getting more money back on not just your credit card but also your membership in general. If you buy groceries with it you’re not getting between 2-4% back from that money.

• 
  @SurfingWithTheMartian5 ай бұрын

  Good video I appreciate you doing it. Getting the electrical connector off the old sensor was tough doing it blind but I was surprised that it eventually came off no problem. Also getting the right combination of sockets and extensions to work took me a while. After getting the old sensor out a fair amount of oil dripped on the ground so I thought I should make sure to put the new sensor in good and tight. Definitely went beyond just snugging it so hope I didn’t crack the case. No oil leaking from the case so far. Thanks again.

• 
  @diydevin5 ай бұрын

  Glad to hear, if it ever does leak in the future some high heat teflon tape will help keep it in there snug without breaking anything.

• 
  @erniev33635 ай бұрын

  If you have the Costco Citi card, you have the option to deposit directly into your bank account.

• 
  @diydevin5 ай бұрын

  That’s only with the Citi cash back not with the regular 2% executive cash back. So yes with the Citi cash back you should do the direct deposit to save more money.

• 
  @meantayo415 ай бұрын

  They don't allow people to get cash anymore?! 😮

• 
  @diydevin5 ай бұрын

  Your Costco might, mine does not allow it anymore. If yours does then I would just cash it out.

• 
  @PinkCarRides5 ай бұрын

  So if I got $100 back I’m doing all of this just to get $1.98 back later? Not much of a hack my friend. Time is money.

• 
  @diydevin5 ай бұрын

  Many people get more than $100 back every year. Some bigger families & businesses even get to the max $1000 you can get back.

• 
  @friday19415 ай бұрын

  Heck a $1.98 could get me a Costco hot dog and drink with change to spare! That’s more than worth it.

• 
  @operationhotshotinc.68875 ай бұрын

  lol exactly

• 
  @operationhotshotinc.68875 ай бұрын

  @@diydevindude do you realize you get the 2% back because you SHOP at Costco. So why not use the money to SHOP at Costco?

• 
  @amazzillaproducts525 ай бұрын

  @@operationhotshotinc.6887 On cash back and Costco gift cards you dont get the 2%. So this would save you at least 2% from my understanding.

• 
  @alejandrotorres46325 ай бұрын

  Can this work for Pioneer dmh t450ex? Was trying to figure it out but the screens show different things

• 
  @diydevin5 ай бұрын

  It has personally worked on every pioneer I have tried it on, it might just be a slightly different sequence. If it doesn't work then you might have to bypass it with a wiring bypass kit from amazon.

• 
  @danielronquillo79235 ай бұрын

  hey man im having the same problem but my truck is a f150 2010 its only when im making a left turn but it makes that grinding noise you was talking bout could this be the same problem

• 
  @diydevin5 ай бұрын

  It is very possible that it’s the same fix, it might also be another type of vacuum leak. If it’s only when you turn left that tells me you have a split in the vacuum hose going to your hub, and when you turn it’s forcing the split apart. I would turn your wheel to the left and then check the hoses coming out of your hub all the way up into your engine bay.

• 
  @mkdalraisi3075 ай бұрын

  Very useful and informative, i have an expedition limited 2016 my front wheels are not rotating on 4H & 4L before that i was getting that grinding noise too, now I'm running only 2 wheel drive , I've checked the solenoid when the vehicle is on there is vacuum on the top nozzle means the solenoid is functioning i only have a doubt on the check valve

• 
  @diydevin5 ай бұрын

  If you don’t have the blue check valve I would replace it regardless. Those black check valves have lots of issues. If that does not fix the issue it might have worn out your hub actuators and you’re going to have to replace those.

• 
  @mkdalraisi3075 ай бұрын

  @@diydevin thank you for responding , the check valve i have is a blue color , one thing i suspect today is when i was bogged in the sand I've turned the dial in 4L drive mode the car did absolutely nothing when i pressed the gas pedal then reversed back and front only rear wheels were turning until the car got free from the sand

• 
  @user-mr8my2vs9f5 ай бұрын

  The sensor requires 21mm deep socket. We measured the sensor with calipers and indeed it is 21mm. A 6 point 22mm would probably catch it but a 12 point 22mm will not. DeVin probably used a 6 point 22mm. Good luck.

• 
  @diydevin5 ай бұрын

  Yes depending on your vehicle it might be a slightly different size.

• 
  @Shannon-Smith5 ай бұрын

  Would this work with the 5.4 3 valve?

• 
  @diydevin5 ай бұрын

  Yes J&L and K&N make a separator that will work with the 5.4 Triton.

• 
  @tankimus6 ай бұрын

  you're leds should also be facing right to left.

• 
  @diydevin6 ай бұрын

  Correct, thank you for the comment.

• 
  @BetoisDmentD7 ай бұрын

  Nice work on this one.

• 
  @diydevin6 ай бұрын

  I appreciate the positive feedback!

• 
  @shaniatsinnajinnie25497 ай бұрын

  What symptoms did your car have at the time of 'low engine oil pressure"?

• 
  @diydevin7 ай бұрын

  If the sensor is bad you won’t have any symptoms the car will drive normal since you don’t actually have low oil pressure. If you’re experiencing other symptoms then there might be another underlying issue.

• 
  @saundrabrown-um1xs8 ай бұрын

  Thanks for sharing 😊

• 
  @diydevin6 ай бұрын

  I appreciate the positive feedback!

• 
  @leonardvoet8 ай бұрын

  Do you have to do this every time the head is powered on or does it remember this setting?

• 
  @diydevin6 ай бұрын

  It will remember the setting.

• 
  @brianlocklear15999 ай бұрын

  Does that work to clear the blue tooth phone files out also?

• 
  @diydevin6 ай бұрын

  It does not

• 
  @spartan930510 ай бұрын

  I don’t have a source off option, I have a dmh w2700nex, how can I get the option?

• 
  @diydevin6 ай бұрын

  Every NEX I have personally tested had that option, but they have mainly been newer units. It might not be an option on yours.

• 
  @scottgates332110 ай бұрын

  great video very helpful Job done in about 15 minutes Thanks for the information

• 
  @diydevin10 ай бұрын

  Awesome, I am glad it helped!

• 
  @theun-typicalchristian778510 ай бұрын

  My 2011 Ford Edge is working again after having flashed “LOW Engine Oil Pressure”, showing check engine light, lost power steering, then completely shut off. It looks like this video accurately identified the problem, though I was able to accomplish the task more easily by accessing the pressure sensor from beneath the car. This required an extension on the wrench in addition to the universal elbow. The powerful light I purchased was also helpful to see by. After starting the vehicle and having it die once more, I tightened the new sensor to ensure its proper sitting and reset the system by detaching the negative (black) terminal on the battery, waiting a while, and reconnecting it before hopping back in and starting it again (always start and end with black; do not touch both end at same time). At this point it has remained running for a promising amount of time and I thank God that I came across this resource and broke down a mile away from an AutoZone.

• 
  @diydevin10 ай бұрын

  I am happy to hear that you got it running again! Thank you for your feedback!

• 
  @theweatherguy98377 ай бұрын

  Hello I have the same problem my Ford Edge 2013 goes off and it’s shows Low engine oil pressure I’ve replaced the sensor I’m still having the issue please help thanks

• 
  @AustinPrincewill5 ай бұрын

  My 2011 Ford Edge is having the same issues . Can you write a step by step process on how you fixed it please?

• 
  @AustinPrincewill5 ай бұрын

  ⁠@@theweatherguy9837Hello, have you finally fixed it ?

• 
  @caseyhunt110 ай бұрын

  I've replaced this and mine is coming on only at idle. any suggestions? how can i check the oil pressure? I replaced the radiator fans too and it helped for a month or so. then started again and it's worse now. every red light it comes on.

• 
  @diydevin10 ай бұрын

  Some auto parts stores will check your oil pressure for free. Or if you have a scan tool with live data it can check as well.

• 
  @joneslr2511 ай бұрын

  So it's it supposed to say set on or set?

• 
  @diydevin10 ай бұрын

  It will say set on, mine said set off because I had done it before.

• 
  @timsmith14811 ай бұрын

  I had to use a 21 mm for my 2013. Not a 22mm.

• 
  @diydevin10 ай бұрын

  Thank you for your feedback!

• 
  @joneslr2511 ай бұрын

  I know I'm late BUT does this work for the Pioneer AVIC-W8600NEX?

• 
  @joneslr2511 ай бұрын

  Yes it does work with the Pioneer AVIC-W8600NEX. I just tested it.

• 
  @diydevin10 ай бұрын

  Thank you for your feedback!

• 
  @juanventura476211 ай бұрын

  Hi, would you know of this works on the DMH-W2770NEX? Been trying and the screen/buttons look a bit different, couldn’t even find the “source off” feature, appreciate your help, I’m stuck with the install. Thanks

• 
  @diydevin11 ай бұрын

  If it's not working you can try pushing the reset button with the end of something small and then try this process again. This has personally worked on every single pioneer radio I have tried.

• 
  @spartan930510 ай бұрын

  Have you gotten it to work?

• 
  @MattBurke-cf2qt5 ай бұрын

  Same issue. I also can't find the source off, and nothing happens when I press the corner of the screen on the main menu. Thanks for the help!

• 
  @jessedubay59644 ай бұрын

  @@MattBurke-cf2qtsame here, let me know if you figure something out!

• 
  @FlyLan2 ай бұрын

  As far as I'm aware, the DMH-W2770NEX is no longer supported by Pioneer (no new firmware updates). All of the NEX units that I've seen this "secret" bypass cheat code work for are the more expensive NEX models that are still getting Pioneer updates. One of the updates added the bypass method shown in this video, but (and I could be wrong about this) the -W2770NEX didn't receive this update. Three-wire, double-pulse micro bypass is the fix for the W2700/70...worked for mine.