Пікірлер

• 
  @rmcoelho18 күн бұрын

  Bevmax 3800 disable from system. May you give me any clue to fix that?

• 
  @Vendingworks18 күн бұрын

  Start with the obvious, make sure your coin mech has plenty of coins in it, specially nickels. Does the machine work correctly if making a purchase with coins only?

• 
  @rmcoelho18 күн бұрын

  @@Vendingworks seconds before I got your answer, I found out about the nickles. Thank you anyway, God bless you.

• 
  @rogergordon6327 күн бұрын

  lovely figure

• 
  @boredinquarentine9601Ай бұрын

  Is there a way to fix the problem shown at time “6:58” by replacing certain parts. If so what parts specifically need replaced?

• 
  @susandaley3713Ай бұрын

  Do buy pop machines

• 
  @kevinsmailes77302 ай бұрын

  Tried contacting you on your website last week about a bill validator for my ICE Pinnacle claw machine. No response so far.

• 
  @Vendingworks2 ай бұрын

  We have no messages from you or anybody asking about a bill validator for a claw machine. Send me a picture of the connector that the bill validator plugs into and I can recommend a bill validator for it. [email protected]

• 
  @davida1hiwaaynet3 ай бұрын

  I realize this is an older video but wanted to say thanks. I am working on one of these and troubleshooting a flash code 11. Everything appears to be clean with both the upper an lower sensors. The machine was bought at an auction and had the hallmarks of an abandoned unit. Had old empty (frozen and burst) drink cans in it, and had money in the coin acceptor. The bill validator was giving code 11, until I blew the parts out with compressed air. It then worked for about two days and then the code 11 returned. I have taken it apart and cleaned the sensors and the plastic windows over them, both sides but the flash code 11 remains. I'm still looking for more info online, but your video was very helpful and I plan to watch more of your videos today.

• 
  @jacquelinewegscheid924516 күн бұрын

  DID YOU FIGURE OUT THAT 11 FLASH CODE PROBLEM?

• 
  @davida1hiwaaynet16 күн бұрын

  @@jacquelinewegscheid9245 Tony, I ended up sending this to the manufacturer. They discovered damage to the lower sensor board. When I took it apart it had signs that a previous repair shop had been in it already. They replaced all damaged and missing hardware from the previous shop, plus replaced the board. Total cost was around $228 for the repairs.

• 
  @kalpatel85373 ай бұрын

  Hi... I'm having an issue with my CoinCo validator where it just keeps making a whizzing noise and tries to start up but then nothing... I've restarted the machine and reset the all the components.. Any idea??

• 
  @Vendingworks3 ай бұрын

  It sounds like the transport motor gears are stripped. This usually happens when somebody is trying to cheat the machine by pulling the bill out as it's being sucked in. You are going to have to replace the bill validator

• 
  @kalpatel85373 ай бұрын

  ​@@Vendingworks ok... do you sell or repair these? It's a Coinco BP2BX.. and again thanks for the supersonic reply!

• 
  @Vendingworks3 ай бұрын

  @@kalpatel8537 Yes we do sell those. vendingworks.com/collections/shop-by-brand-3/products/coinco-bill-pro

• 
  @highlandcitylibrary57803 ай бұрын

  Thanks so much for posting this!

• 
  @MatTodd-hp2sm3 ай бұрын

  Hello - what model Dixie is this? I have the exact same one but the ID plate is missing and I don’t know how to identify it! Thank you

• 
  @Vendingworks3 ай бұрын

  I think it's a 368

• 
  @hawsug46143 ай бұрын

  Thanks.

• 
  @hawsug46143 ай бұрын

  Our Coinco 9300 only has three pins. How do we change the price (to $2)?

• 
  @Vendingworks3 ай бұрын

  Sounds like you have a 9300L. With that model you would change the price through the computer in the machine and not the coin mech. There should be instructions printed on the inner door of the machine

• 
  @jeepyj103 ай бұрын

  Can you explain the options switches?

• 
  @user-dj5my5fb7k4 ай бұрын

  Hi , how to setup mei sc advanced in window 10 ?

• 
  @13visualz4 ай бұрын

  We are having problems with ours

• 
  @Vendingworks4 ай бұрын

  What type of problems are you having?

• 
  @trogers81804 ай бұрын

  I’m doing this test currently. Do you have a video on how to recharge the system?

• 
  @kalpatel85375 ай бұрын

  hi, I have a Mars Validator that accepts one bill, but won't accept any subsequent. All the coin chutes are full... I'm stumped.

• 
  @Vendingworks5 ай бұрын

  You need to change the escrow settings in your machine, it has nothing to do with the bill validator

• 
  @kalpatel85375 ай бұрын

  OK thx for the fast reply!

• 
  @dm15175 ай бұрын

  Hi. My coinco BA50B doesn’t make any noise at all…

• 
  @marcellusnorwood5 ай бұрын

  What are you using to test the bill acceptors

• 
  @DrewAk495 ай бұрын

  Thank you! Your video helped me out a lot!

• 
  @stuchambers2975 ай бұрын

  how do you program a Mars MS1000 it has 3 blue buttons , wouldn't have a glue which button does what

• 
  @stuchambers2975 ай бұрын

  Can a Mars MS1000 be updated to a more modern version of a coin validator?

• 
  @kornfedkustoms15486 ай бұрын

  I have a freshly rebuilt mag62BB and it will take a 1 dollar bill but not 5 and it will not give credit for the $1 bill. Its set for 4pulses per dollar. Hate to have to send it back in!

• 
  @Vendingworks6 ай бұрын

  Is the #6 switch on so it will accept $5 bills and has it been updated so it accepts the new bills?

• 
  @kornfedkustoms15486 ай бұрын

  All the dip switches are correct going by my other 2 validators and coinco manual. I ended up sending it in the mail to coin acceptors in missouri to have them look at it. Ive had this happen in the past and i think they said it was something they messed up with the programming? Thanks for your quick reply. Nice video!

• 
  @MarioHernandez-dx1yf7 ай бұрын

  It works for other country coins?

• 
  @Jerick9002 ай бұрын

  Have you found out if it does?

• 
  @PersonalUseChannel7 ай бұрын

  I think I picked one up from you a while ago. you in Ontario, CA?

• 
  @rigobertodimas80147 ай бұрын

  My bill valadater is connected but I noticed it has a plug in not connected idk what the plug in gose to can u please tell me also my bill valadater lights are not working at all im thinking the not plug in is for the lights for the valadater I just don't no at all places hit me back

• 
  @roschellTate-pq9vn8 ай бұрын

  Hello, when I put a bill in it goes in but goes up half way, it does not go into the bill holder.

• 
  @Vendingworks8 ай бұрын

  If it goes half way and then stops, that is usually an escrow setting in the vending machine. it holds the bill until a purchase is made or if you press the coin return it will return the bill. If you are talking about a Coinco Bill Pro model (BP2BX, BP4SX, etc.) validator then the board is bad and you need to replace the whole bill validator

• 
  @instafixies82088 ай бұрын

  Hi, Good work with the video. Just have a quick question. We have vending machines and some of them have ice formation on evaporator. We have tried every possible thing but no solution. Last we’ve asked by OEM to replace evaporator fans with higher RPM ones. Will that help? Btw: it’s hot food vending machine with target temp @ 3-4 degrees. Hope I didn’t bother. 😊

• 
  @Vendingworks8 ай бұрын

  If ice is forming on only part of the evaporator then that usually means there is a leak and it's low on charge. If you could send some pictures I'm sure I could diagnose it for you [email protected]

• 
  @pimpstar29 ай бұрын

  good info.....

• 
  @windturbineclimber54129 ай бұрын

  This is a good video. Thank you. But I have a different problem. All of the drinks in my machine are freezing up. What could be the problem? How can I fix this? Also, I see that you have a lot of units in the background, do you sell parts? Where can I find a schematic for this machine?

• 
  @Vendingworks9 ай бұрын

  If the drinks are freezing then you just need to replace the thermostat. Schematic for the machine you can usually find on the inner door of the machine. We sell coin mechs, bill validators, and refrigeration decks for vending machines.

• 
  @windturbineclimber54129 ай бұрын

  @@Vendingworks Thank you that helps alot. The schematics are missing on this machine. I have looked everywhere. Do you have a website or somewhere I can order parts from yall online?

• 
  @Vendingworks9 ай бұрын

  @@windturbineclimber5412 Vendingworks.net is our website

• 
  @LuisOrtiz-vo3ed9 ай бұрын

  I think number 7 is the led high Visibility one lol

• 
  @Tay-vk3et10 ай бұрын

  Did this. compressor came on when plugged in however there was no ice around evaporator and it was warm to touch. potential compressor replacement?

• 
  @Vendingworks10 ай бұрын

  Sounds more like there is a leak and no refrigerant left in the system

• 
  @Tay-vk3et10 ай бұрын

  @@Vendingworks thank you!

• 
  @keithculvahouse119110 ай бұрын

  is there many differences between calibrating this coinco coin mech or a 9302gx?

• 
  @Vendingworks10 ай бұрын

  It's the same to calibrate unless it's a Coin Pro 3 then it can only be calibrated by Coinco

• 
  @keithculvahouse119110 ай бұрын

  wish your sound was better in this video

• 
  @InvestmentJoy11 ай бұрын

  Yes! So awesome! Have a stack of these to go through and figure out compatibility!

• 
  @earthsky573411 ай бұрын

  Appreciate your presentation and Explaining Thank you

• 
  @earthlysoundsoftheworld655411 ай бұрын

  Great 🎉 informative video I just started in the vending machine business and my bill validator just stop working and no flash to it I’ve done mostly every in this video you have shown but my machine is only accepting coin do you have a solution

• 
  @Vendingworks11 ай бұрын

  Is the red LED on solid? If it's off then it means your coin mech is low on coins in the coin tubes. Make sure you have plenty of nickels

• 
  @1marktran11 ай бұрын

  How many teeth does this belt have? Parts catalog have two kind.

• 
  @Fotopro Жыл бұрын

  Great video. Thanks! Do you have any idea why my BA30SA will only accept the first bill, and motor doesn’t register a second bill? I’ve checked escrow/stack setting in the machine (Dixie Narco 501T). When I make changes to the ESC settings the Coinco bill collector will accept a 2nd bill, but only for 1 vend. The next purchase it goes back to only accepting one bill. Do you have any idea what could be causing this? Thank you.

• 
  @Vendingworks Жыл бұрын

  Purchase the most expensive item in the machine using only quarters, then try again with the multiple bills. Make sure your coin mech is full of coins. You may have a bad lower sensor in one of the coin tubes of the coin mech so it is thinking it doesn't have enough coins to make proper change.

• 
  @Fotopro Жыл бұрын

  @@Vendingworks that’s a good idea. Can you clean the sensors, or do I need to send the coin mechanism in for service. Thanks!

• 
  @Vendingworks Жыл бұрын

  @@Fotopro Ususally cleaning the sensors on a coin mech won't help

• 
  @clarencehoward5554 Жыл бұрын

  My ba validator doesn't even try to accept the dollar. When I put the money into the slot the machine doesn't give off any sound and the bill just crumbles up as I try to insert it

• 
  @dannyspells9853 Жыл бұрын

  My question is is it possible to sat my coin mechanism to only accept quarter no nickel no dime it’s a TRC - 6800h this model accept all 3 coin I’m just wanting to accept quarter thanks

• 
  @pyrocat1150 Жыл бұрын

  I have a Royal 552-8, the condenser is frosted over heavily. I've unplugged machine for a few days and turned it back on. The top 2/3 of condenser has thick layer of frost. Door seals are good. We have duplicate machine that has clear condenser so we are wondering what's wrong. It does cool just fine

• 
  @matthewpreston837410 ай бұрын

  Bad evaporater fan motor? check amp load

• 
  @michelereese1952 Жыл бұрын

  The coinco takes the dollar bill but does not give a dollar credit, any ideas?

• 
  @edochamp Жыл бұрын

  Great info. Please keep posting videos like this.

• 
  @user-xg9um1mr4g Жыл бұрын

  Thank you for your video. It was very good. I have a used 501e pop machine and the evaporator fans run all the time. My machine is located indoors and I can hear when the condenser kicks on and off. Is there a way to quiet the evaporator fans when is is not cooling down the cold box?

• 
  @justinroell3215 Жыл бұрын

  Thank you for the video! My machine makes the correct noise, but the dollar will not go in at all. Any suggest?

• 
  @tambourahorton8579 Жыл бұрын

  Thank you for a well explained video. How would I know if my validator has flash port or not? And if it does how can I get it to accept 5’s? Thank you.

• 
  @mahfuzmusa1588 Жыл бұрын

  nice

• 
  @litashamarii6606 Жыл бұрын

  I just recently bought a machine i put a dollar it keeps getting stuck leaving a inch of dollar showing please help

• 
  @ssboxer456 Жыл бұрын

  Can you please help me out?

• 
  @Vendingworks Жыл бұрын

  What do you need help with?

• 
  @FuquarProductions Жыл бұрын

  My evaporator is completely turning into a block of ice.... Low refrigerant possibly?

• 
  @Vendingworks Жыл бұрын

  If it is completly covered with ice then the refrigerant charge is fine. The problem is going to be a bad thermostat or bad evaporator fan. If the evaporator is only partially covered with ice then there is a leak in the system and it is low on refrigerant

• 
  @FuquarProductions Жыл бұрын

  @Vendingworksnet as it turns out I moved the thermostat all the way up and down a few times then back to set temp and the problem cleared up.