How to Calibrate a Mars / MEI TRC Series Coin Changer
Тәжірибелік нұсқаулар және стиль
www.vendingworks.com/ This is an instructional video to show you how to field calibrate a Mars TRC series soda vending machine coin mech. Vending Works sells coin changers, bill validators and belt kits for bill validators as well as refirgeration decks for Dixie Narco and Vendo soda vending machines
Пікірлер: 33
what if after 20 coins of each basic 3 it still doesn't accept anything?
Nice video, thank you for sharing.
My question is is it possible to sat my coin mechanism to only accept quarter no nickel no dime it’s a TRC - 6800h this model accept all 3 coin I’m just wanting to accept quarter thanks
I had a mech serviced, and it won't take any coins. Does that mean it's in learn mode? There seems to be a plate blocking any entry of coins in the acceptor tubes
@Vendingworks
3 жыл бұрын
First thing I would check (most common) is if you have a jammed can in one of the columns. If any of the vend motors are not in the "home" position, the machine will not accept money. The machine thinks it's in the middle of a vend cycle and therefore will not accept any money until the vend cycle completes. Could also be a bad micro switch on one of the vend motors. Also, if the machine has no product in it, it will not accept money
Esta mostrando solo las monedas salir?
Is it possible to interface a bill validator to a TRC-6000? If so could someone point me to the correct validator?
@Vendingworks
Жыл бұрын
No you can't connect a bill validator to a Mars TRC6000. The coin mech and the bill validator connect to the machine independently of each other, they don't connect to each other.
Is there a way to calibrate a MDB mech without sending it in?
It works for other country coins?
@Jerick900
3 ай бұрын
Have you found out if it does?
Teach about change the magnets from both side without break it them
Teach how to change the magnets without break them
How do you set the price?
@arko2094
2 жыл бұрын
It’s the switches from that say price.
@arko2094
2 жыл бұрын
They start off from left to right. The first switch on the left will be 5 cents then. Doubles.
Will coin reject of the coin tubes aren't filled ? I have a 6800. I plugged it in and coins just fall through .
@Vendingworks
3 жыл бұрын
That is most likely not a coin mech issue, probably have a jammed can in one of the columns. The coin mech will not accept money if one of the vend motors is mid cycle (caused by a jammed can). Check to make sure all vend motors are in home position
@SLAPSHOP42
3 жыл бұрын
@@Vendingworks there is no product or jams present in the machine . Mech is plugged into Jones plus . Inserts coins and they fall through ...
@Vendingworks
3 жыл бұрын
@@SLAPSHOP42 There must be product (past the sold out paddle) in at least one column for the coin mech to work. It will not accept monet if there is no product to buy
@SLAPSHOP42
3 жыл бұрын
@@Vendingworks older machine there is no sold out paddles .
@SLAPSHOP42
3 жыл бұрын
I tried retuning all the coins with passing through the rejector go to left side and don't drop into the change tubes . I assume I have a dead mechanism ...?
What happens if coins keep going to refund slot? After trying to reteach it? How do you know it's in reteach mode?
@Vendingworks
4 жыл бұрын
Once you put it the 2 nickels, 2 dimes, 2 quarters, and 2 dollar coins, it will make a noise, like it's kicking out a coin. That's the only way to tell if it's in teach mode. If it is still not working, and y ou can't get it to calibrate, it should be replaced.
Mine looks way different. Theres only a 4 pin dipswitch
@Vendingworks
3 жыл бұрын
Yes, only the single price model has two banks of switches, the logic and MDB models have one set of 4 switches. They still calibrate the same way
@GalitUnggoy
3 жыл бұрын
Ive tried to calibrate it using this method. My trc6010 might be bad.