Пікірлер

• 
  @dylanlagerstrom217411 күн бұрын

  You did a mod that cost you $4?

• 
  @forrestgumballАй бұрын

  Shit works 👍👍. Just gotta pop the bumper after screw #3

• 
  @brian17152 ай бұрын

  Bro broke a bunch of clips and makes a how to video come on man lol

• 
  @rafaelramirezaparicio92892 ай бұрын

  Compre mi veloster Aqui en Tijuana Mexico y gracias por video ya voy aprendiento y cambiando fallas k me precentan ered todo un mecanico profecional amigo

• 
  @rafaelramirezaparicio92892 ай бұрын

  Hracias muchas gracias por todo los videos k subes y espero sigas subiendo mas cada k puedas o agas algun cambio del veloster ya que to soy tu seguidor y fans numero 1 acabo de comprar mi veloster y no se nada de servicios

• 
  @rafaelramirezaparicio92892 ай бұрын

  Gracias amigo

• 
  @rodnocker5054 ай бұрын

  You still didn’t show how the bumper comes apart from fender to get said headlight out

• 
  @Paulieman205 ай бұрын

  Does this constantly tick? even at idle?

• 
  @Paulieman205 ай бұрын

  at engine start does yours constantly click? even at idle?

• 
  @Paulieman205 ай бұрын

  is it good to have both? BOV and side of engine? also! do they use the same connector?

• 
  @901Birdie7 ай бұрын

  I spent 2 hours tRNA find where to put the power supply. Thank you, you literally showed me, and I got it done less than 5 mins… 😂

• 
  @n.a.k43217 ай бұрын

  I'm glad it was helpful 👍🏾

• 
  @901Birdie7 ай бұрын

  @@n.a.k4321 it definitely was. I appreciate it, I got most of the wiring hooked up now, I just gotta “safely” wire my capacitor😂 I’ll post some videos once my setup is done. If ya want a shoutout I got you 🙏 you deserve the credit🦅

• 
  @n.a.k43217 ай бұрын

  @901Birdie would be greatly appreciated, and thanks in advance, I'll definitely check out the video's

• 
  @returned4good9 ай бұрын

  Thank you very much; this is exactly what I needed to know. Bookmarking for future reference.

• 
  @caitlinchrisp61089 ай бұрын

  *promo sm*

• 
  @tomc86179 ай бұрын

  Re: "Candy Corn" Got me craving some Halloween candy! Fortunately, the stores are now carrying it, with Halloween coming up next month! :)

• 
  @n.a.k43219 ай бұрын

  Happy holidays!

• 
  @skeezinondembois10 ай бұрын

  I have 2013 veloster as well still running hard but I got the same code P0455 and P0441 …. I replace the same part too … imma try the silicone but but do you have suggestions about the p0441

• 
  @n.a.k432110 ай бұрын

  The silicone should get rid of the code. iv only done it once, and the code never came back. Other than that, clean the mass airflow sensor and any electrical plug you can get to. Hopefully, it will fix the problem

• 
  @jasminechandler394510 ай бұрын

  Thanks!

• 
  @n.a.k43219 ай бұрын

  You're welcome

• 
  @Bleefit10 ай бұрын

  Five years later, and this is still valid thanks bro!

• 
  @n.a.k432110 ай бұрын

  Your welcome

• 
  @ryansangalang34311 ай бұрын

  Great job. I wish you had an instructional video to come with it. I think I might have the same issue.

• 
  @n.a.k432110 ай бұрын

  once you locate the oil cooler, you'll see a drip line down the side or front of it that how you'll know for sure or drop so cardboard down to see where the leak is coming from. Check oil bolt first if thats tight,and not leaking, it's would most likely be oil cooler, and truly, the worst part is getting the squeeze clips off

• 
  @ryansangalang34310 ай бұрын

  @n.a.k4321 thanks for the response. I bought the oem oil cooler. Now I just some time after work or weekend to do it. But lately it's been over 90° 🔥🔥🔥

• 
  @n.a.k432110 ай бұрын

  Same here, be careful/safe. oh, if you have a jar for swearing, just sit beside you while you're under the car 🤣😂 enjoy

• 
  @ryansangalang34310 ай бұрын

  @@n.a.k4321 hahahaha! I'll try to remember that! 🤣😂🤣😂

• 
  @Just_Donte11 ай бұрын

  Bro is a legend

• 
  @n.a.k43219 ай бұрын

  Thank you

• 
  @Jondb45 Жыл бұрын

  Oh man. Thank you! I thought I was going to need to spend money. This worked perfect!

• 
  @A_Bester Жыл бұрын

  Great Thanks, I had trouble getting access tot he passenger side headlight bulb and this showed me how not to break the assembly because I couldn't see the 3rd 10mm bolt. Cheers

• 
  @Avgucci Жыл бұрын

  Nah that ain’t it fam

• 
  @n.a.k43219 ай бұрын

  Sorry it doesn't work for you. Was just giving a suggestion on how to get a little more sound out of the horn on a budget, and it's plug and play

• 
  @karmag1891 Жыл бұрын

  Can someone please tell me what this part is called I’m having this problem myself.

• 
  @rickrhendon7720 Жыл бұрын

  Thanks! Our wiper fluid reservoir started leaking, need to change/fix that.. this helped, thank you

• 
  @stevel4127 Жыл бұрын

  Great video! After removing "Screw #3" I was able to just pop the bumper out on the side of the car and access "Screw #4". Thanks!

• 
  @chris_allupinya5613 Жыл бұрын

  This design is absolutely horrendous. I just wanna change my freaking bulb. Why does it have to be so damn difficult

• 
  @n.a.k4321 Жыл бұрын

  it's not that bad 🤣

• 
  @kevinokeefe9163 Жыл бұрын

  Hi, This is info is great! I bet my 2016 Veloster base is the same. I figured there were more than just the 2 bolts that I can see & now I know. I can see that little clip that it slides into, but think my light housing that’s broken might also have that broken too, but will soon find out. I’m in Canada so will scout out where I can buy the replacement parts.

• 
  @kevinokeefe9163 Жыл бұрын

  I took it off so easily thanks to your instructions and advice! I’m trying to glue the housing together instead of buying a new one first because a new one is $$$!

• 
  @notgray88 Жыл бұрын

  How did you get the bumper off like that?

• 
  @n.a.k4321 Жыл бұрын

  One screw in each of the fenders' four pop-up tabs in the top, and the bumper should lean forward to reach the third bolt under light. But Be extremely careful

• 
  @johngaltspeaking213 Жыл бұрын

  This is a great video but I can't begin to explain how much I hate this car and to date it's my worst purchase ever. Such drama just to replace a bulb.

• 
  @n.a.k4321 Жыл бұрын

  It's not that bad 🤣

• 
  @diegocueva1434 Жыл бұрын

  I’m just wondering how you got the lil cap off? Did you just use your hands or a knife or maybe a heat gun? Wondering because I don’t want to damage the speaker itself with a knife

• 
  @n.a.k4321 Жыл бұрын

  Mine fell off inside the door do to heat so heat gun may be the best bet but I'm not saying it will work check out some videos on how to rebuild speakers mite get some good ideas from there

• 
  @onetime7539 Жыл бұрын

  Well done didn’t even need to pull it all the way out. Just need a bit more room. Done in less than 10 mins. 2015 Veloster

• 
  @n.a.k4321 Жыл бұрын

  Thanks glad the video was helpful (enjoy)

• 
  @DavidMadeira29 Жыл бұрын

  I'd rather say the terrible mod...

• 
  @Daddy53751 Жыл бұрын

  So this is an opaque paint?

• 
  @n.a.k4321 Жыл бұрын

  It was a special paint option for that year I haven't seen it anymore apologies don't know the answer to your question

• 
  @warrengamameilhardin Жыл бұрын

  Thank you, this helped me! I found only 3 bolts actually hold the assembly in, but you have to take the bumper bolt from in the wheel well off anyway in order to pop the bumper out to make room for a socket wrench to get the lamp assembly bolt out. You also have to take two bolts and a plastic pop fastener out from the top of the bumper in order to bend the bumper up and out slightly, to make room for sliding the assembly out forward and putting it back.

• 
  @n.a.k4321 Жыл бұрын

  Correct I found a way to bypass all the extra work once I removed the bumper cover a few times

• 
  @liampurves3406 Жыл бұрын

  very helpful thank you tons

• 
  @JoseSandoval-ic5xe Жыл бұрын

  Hi did this feel better than OEM and does this replace Bov solenoid? Thanks

• 
  @n.a.k4321 Жыл бұрын

  If done correctly yes

• 
  @JoseSandoval-ic5xe Жыл бұрын

  @@n.a.k4321 Thank you, sorry what do you mean by if done correctly?

• 
  @n.a.k4321 Жыл бұрын

  @@JoseSandoval-ic5xe if you hook allmthe hoses in there correct places you will notice a slight difference if you hook them up wrong you'll go into limp mode.

• 
  @n.a.k4321 Жыл бұрын

  Sorry txtn on the fly lol

• 
  @n.a.k4321 Жыл бұрын

  @@JoseSandoval-ic5xe also I ended up moving mine over to the turbo side it worked better for me

• 
  @kaylagrater687 Жыл бұрын

  how did you block off the OEM part towards the wheel well? that's what i'm trying to figure out right now.

• 
  @kaylagrater687 Жыл бұрын

  mine sounds overly "whoosh-y" and it's annoying ash

• 
  @n.a.k4321 Жыл бұрын

  I removed it all together

• 
  @michaeltypaldos7246 Жыл бұрын

  very helpful my man. Went to replace the led low beams and the damn spade wiring in the connector fell out. (Previous owner installed) I had to remove the headlight and solder the connections across. Easiest way! Now if only there was a way to fix the plastic mounting support after its ripped off from the bumper(Happened when I hit an animal on the road)

• 
  @n.a.k4321 Жыл бұрын

  Super glue and tp. 😁

• 
  @greenpeach1002 жыл бұрын

  Hey man I tried doing this but the Mac bov I tried to plug into the wastegate port was different so it couldn’t fit, did you have this issue? The only way was to dremel the outer casing of the port from the Mac bov so it could fit, but I believe my car is in limp mode from it cause I have no boost now

• 
  @n.a.k43212 жыл бұрын

  No sir I didn't run into any issues with the install I bought the fittings from hardware store took the hoses.and the mac valve with me

• 
  @n.a.k43212 жыл бұрын

  Also make sure you plugged everything back in its proper location

• 
  @greenpeach1002 жыл бұрын

  @@n.a.k4321 you think I can just cut the ports off and just wire the positive to positive and negative to negative?

• 
  @n.a.k43212 жыл бұрын

  May I ask what year and what are you trying to do with the Mac valve? don't cut ports off yet

• 
  @n.a.k43212 жыл бұрын

  it's better if you could get under the car for the installation and use hoses for ports you can take original hoses to auto part store and grab some similar to it you'll have to use clamps i found some tha fit at the hardware store as well

• 
  @badass1g2 жыл бұрын

  Wow that under the bulb 10 mm I was like wtf is holding it on there?!? Thanks sir

• 
  @n.a.k43212 жыл бұрын

  You're welcome

• 
  @metroid20992 жыл бұрын

  May of 2022 and this vid helped me out. Thanks man. Videos like this help keep things running longer.

• 
  @n.a.k43212 жыл бұрын

  Awesome glad I could help

• 
  @dchiznit209 Жыл бұрын

  I have to replace the entire assembly for a 2019, are the bolts still roughly the same? I don’t know jack about cars and don’t want to drop 2,500 if I can do it.

• 
  @marcusgreen93002 жыл бұрын

  I been trying to get my lights put all day... now I know what I was doing wrong..

• 
  @n.a.k43212 жыл бұрын

  Glad this video was helpful

• 
  @Xizax413252 жыл бұрын

  Swapping out my assemblies on my 2016 this weekend. I'm sure this will be helpful.

• 
  @n.a.k43212 жыл бұрын

  Glad I could assist good luck and be careful

• 
  @gary-ln9td2 жыл бұрын

  I know this is old but thank you for the video

• 
  @n.a.k43212 жыл бұрын

  You're welcome 😊

• 
  @stanza772 жыл бұрын

  What’s the name of that part please so I can order one thank you

• 
  @n.a.k43212 жыл бұрын

  look up purge valve or purge silnoind

• 
  @hagerz2 жыл бұрын

  Absolutely helpful. Thank you sir 👍👍🏁🏁

• 
  @n.a.k43212 жыл бұрын

  Your welcome

• 
  @elgilbertgt95932 жыл бұрын

  What is the número the part

• 
  @n.a.k43212 жыл бұрын

  Sorry I don't remember the part number

• 
  @tvzone12652 жыл бұрын

  Thanks!

• 
  @n.a.k43212 жыл бұрын

  Your welcome 😁

• 
  @jonathanchavers9612 жыл бұрын

  How to solve problem step 1. Dont own a veloster.

• 
  @n.a.k43212 жыл бұрын

  the car is pretty decent for what it is (1st gen) the N models are going to be the game changers

• 
  @robmapes43062 жыл бұрын

  Thank you for the clue - I used your firewall grommet method (on the passenger side) which worked easiest for me because It just pops right out when you pull on it. Then, fishing the new cables is easy - I first fed one end of a small chain (I used a pull chain from a light fixture) through the opening from the engine compartment side through to the passenger side interior - it was easy to locate where the other end of the chain appears on the passenger side interior as you feed it through. Then I attached the engine compartment end of the chain to the new cable and pulled the new cables through the hole. It took less than 10 minutes!

• 
  @n.a.k43212 жыл бұрын

  Your welcome I added a boost controller and a auto system to my veloster with that method glad I could help