Пікірлер

• 
  @JH-ve6tx2 күн бұрын

  Good video. I'd probably pull that fender ground and clean it up as well. It looks like it has the green crusties too! My edge is the same way.

• 
  @TheBatteryShop2 күн бұрын

  Thanks for watching and adding to the conversation!

• 
  @plm5122 күн бұрын

  Thanks for the information. Just did my 2009 Traverse. I used the battery saver and turned off the interior door open lights so it wouldn't draw from the battery saver when doing the battery swap. Worked as planned. Started up and kept all the settings. Thanks again for the help.

• 
  @TheBatteryShop2 күн бұрын

  Thank you for watching and glad we could help!

• 
  @christianacosta71063 күн бұрын

  Best video on how to change batteries. Step by step and everything explained thank you

• 
  @TheBatteryShop3 күн бұрын

  Thank you for watching and glad we could help!

• 
  @streetman233 күн бұрын

  Battery on my 2015 volt is dying. This was helpful. Had to pay close to $200 for a replacement

• 
  @TheBatteryShop3 күн бұрын

  Thank you for watching and happy to hear we could help!

• 
  @mikefitzsimons31503 күн бұрын

  Thanks much!!

• 
  @TheBatteryShop3 күн бұрын

  Thank you for watching!

• 
  @trevordorman43845 күн бұрын

  awesome in depth video thank you!

• 
  @TheBatteryShop3 күн бұрын

  Great to hear and thank you for watching!

• 
  @user-ko7mg2cz6n5 күн бұрын

  Something I love about Germans they make everything so easy to change easy as to escape to a maximum security jail 😅 That's why I love japanese cars.

• 
  @stephenjackson43927 күн бұрын

  Why does no one explain the setting on the multimeter? I have one but don't understand the various settings

• 
  @waitandhope8 күн бұрын

  It's called an insulation pad

• 
  @TheBatteryShop8 күн бұрын

  Thank you for watching and adding to the conversation!

• 
  @painmad8 күн бұрын

  I heard I need to scan the car because I replaced the battery... Did you do that?

• 
  @TheBatteryShop8 күн бұрын

  Thank you for watching. Some vehicles need to go through a registration process upon installing a new battery. We would recommend consulting your dealer or a mechanic to verify if your vehicle needs it.

• 
  @microtech58719 күн бұрын

  Is this the same process for newer explorers? 2024/2025?

• 
  @TheBatteryShop8 күн бұрын

  Thank you for watching. For a 2024 we do know the battery is located in the same general location but have not gone through a step by step process of replacement.

• 
  @doctajonz28289 күн бұрын

  Thanks for the video. Weird thing with my 2015 GS 350, I replaced the battery but didn’t do the memory saver technique and all my presets (radio, clock, etc.) remained. Hmmm.

• 
  @TheBatteryShop8 күн бұрын

  Thanks for watching and happy to hear everything remained the same.

• 
  @marckrems7799 күн бұрын

  What do I hook up to the jump terminals to keep my settings ? And then simply buy one of the OBDMs to tell the car a new battery was put in ? Mine is a 2016 gle350

• 
  @TheBatteryShop8 күн бұрын

  Thank you for watching. We used an OBDII compatible memory saver to save presets while the battery exchanges takes place.

• 
  @marckrems7799 күн бұрын

  This is the best video on YT for this model I bet Mercedes plays this when they train the techs

• 
  @TheBatteryShop8 күн бұрын

  Thanks for watching and your comments! Glad we could help out!

• 
  @PapaRolo9 күн бұрын

  Would it make a big difference if I just install a battery and be in my day instead of having to do the BMS Stuff?

• 
  @TheBatteryShop8 күн бұрын

  Thanks for watching. Some vehicles need to go through a registration process after a battery change. We would recommend contacting your mechanic or dealer if your vehicle needs the registration. If it does need the registration and its not completed proper charging of the battery may not take place.

• 
  @Eagle1279 күн бұрын

  Much easier to unbolt the front seat 4 bolts and tilt back.

• 
  @TheBatteryShop8 күн бұрын

  Thanks for watching and contributing to the video.

• 
  @MikeyLion10 күн бұрын

  Thank you!

• 
  @TheBatteryShop8 күн бұрын

  Thank you for watching!

• 
  @elbingonzalez750911 күн бұрын

  Hii,how it’s call the little cable that is in the the negative cable,I broke mine by mistake and know my car says battery charging system problem,pls someone help me

• 
  @TheBatteryShop8 күн бұрын

  Thank you for watching. We would recommend you consult a mechanic or dealer for the electrical concerns.

• 
  @mariaferris232612 күн бұрын

  Thank you. Single woman here with limted funds so I really appreciate the easy to follow instructions.

• 
  @TheBatteryShop8 күн бұрын

  Thank you for watching and very happy we could help!

• 
  @moniquelynwone822814 күн бұрын

  Great video thank you 🥰

• 
  @TheBatteryShop8 күн бұрын

  Thank you for watching and glad we could help!

• 
  @Nanajammer16 күн бұрын

  What is 5 Newton meters?

• 
  @TheBatteryShop8 күн бұрын

  Thank you for watching. Newton meters is the amount of force applied to an object. In this case of tightening the fasteners you do not want to overtighten or over torque. We would recommend you consult the manufacturers step by step instructions to know how much force is used to tighten the fasteners on the cable ends.

• 
  @fixingandmore477617 күн бұрын

  Thank you for this helpful video. Can you tell me please what is the right battery size for Ford F150 2016/2017/2018 V8 ? AMPS AND CCA

• 
  @TheBatteryShop15 күн бұрын

  Thank you for watching and glad you found it helpful. The battery size and CCA for these year ranges vary by engine size and model that you have. We would suggest visiting autobatteries.com for proper fit and function.

• 
  @Plumbtired17 күн бұрын

  Not done. That new battery has to be coded to the car’s computer. Launchpad makes an excellent code reader to do this. Cheaper than a mechanic and easy to use. If you don’t register the new battery to the computer it will not charge completely. The computer will charge the new battery at the old rate. Defeats getting a new battery. Edit: actually the battery will overcharge if you do not close the battery my mistake

• 
  @TheBatteryShop15 күн бұрын

  Thank you for watching and for contributing to the conversation!

• 
  @foodrealityeconomicsfe785119 күн бұрын

  Thank you so much for everything from details to diy

• 
  @TheBatteryShop15 күн бұрын

  Thank you for watching and glad we could be of assistance.

• 
  @mandeango119 күн бұрын

  Thank you Gentlemen!

• 
  @TheBatteryShop15 күн бұрын

  Thank you for watching and glad we could be of assistance.

• 
  @oladipo895119 күн бұрын

  Never thought I'd need a tutorial to replace a battery.

• 
  @driellygomes14516 күн бұрын

  The same to me

• 
  @TheBatteryShop15 күн бұрын

  Thank you for watching and hopefully we could be off assistance.

• 
  @flyingark17319 күн бұрын

  Thank you for making this video. There are so many saying to remove the wipers and the cowling, and they call that the "easy way"! I knew there must be a way to do it without all that work, so thank you

• 
  @TheBatteryShop15 күн бұрын

  Thank you for watching and glad you found this helpful.

• 
  @Stevespecs20 күн бұрын

  You didn’t reset the BMS

• 
  @TheBatteryShop15 күн бұрын

  Thank you for watching and for contributing to the conversation!

• 
  @DreDiesley22 күн бұрын

  Thank you very helpful love the music

• 
  @TheBatteryShop21 күн бұрын

  Thank you for watching and glad we could be of help!

• 
  @billredding200022 күн бұрын

  Thanks for showing how to disconnect the Jeep's positive battery terminal properly/safely (without damaging it, too) -- I don't think any other KZread videos show this process. I had never seen this kind of battery terminal design so couldn't figure how -- when the battery was still in the Jeep -- to remove the terminal until after I disconnected all the cables, left the positive terminal still on the battery post, took the battery inside to clean and put it on a charger/de-sulfator (from "BatteryMINDer") for a few days. I could then see how that "camming mechanism" to tighten the positive terminal onto the battery post worked AND more clearly see the plastic "latch" clipping on the the top edge rim of the battery that you have to undo to get the terminal completely off. IMO however, it seems unnecessarily complicated, not to mention an "unconventional" way to tighten the terminal on the battery post itself (and doesn't seem that secure). A very "non-standard" (and unexpected!) obstacle if you didn't know this beforehand as it's unlike most other auto batteries' simple/basic terminals we've had for decades! Jeep is got a bit weird with that design! ;-) -- BR (2021 Jeep Gladiator Rubicon)

• 
  @TheBatteryShop21 күн бұрын

  Thank you for watching. Glad we could help!

• 
  @sailorceee23 күн бұрын

  What memory saver do you guys use?

• 
  @TheBatteryShop21 күн бұрын

  Thank you for watching. We use an OBDII port style memory saver.

• 
  @niacal4nia24 күн бұрын

  Can I use a 12v obd2 port memory saver on Tesla model 3?

• 
  @TheBatteryShop24 күн бұрын

  Thank you for watching. The Tesla Model 3 does have an ODBII port but we would recommend checking with your dealer if a memory save should be used during installation of a new battery.

• 
  @johnciulla258125 күн бұрын

  All this is just for a battery replacement??? Hopefully, there are jump terminals. This is why i love older vehicles.

• 
  @TheBatteryShop24 күн бұрын

  Thank you for watching!

• 
  @jamesa476225 күн бұрын

  Thank you for this video it was a life saver…ford’s design/battery location sucks for these models tho

• 
  @TheBatteryShop24 күн бұрын

  Thank you for watching and glad we could help you out!

• 
  @Stanley-px3bt25 күн бұрын

  Well, this explains when I have not needed to replace my battery yet. I live in Phoenix AZ. When I owned previous vehicles, where the battery was stowed under the hood, I always had to replace the battery every two years when the Arizona heat killed it.

• 
  @TheBatteryShop21 күн бұрын

  Thank you or watching!

• 
  @tiearrajordan11927 күн бұрын

  Lord I'm going to the same problem already and just purchase the vehicle this year in February 🤦🏽‍♀️🤦🏽‍♀️🤦🏽‍♀️🤦🏽‍♀️

• 
  @TheBatteryShop27 күн бұрын

  Thanks for watching and hope this helped you when it comes time to replace your battery.

• 
  @user-nx5mc9ti1q27 күн бұрын

  Which battery is going on audi q5 2.0 tfsi quattro 211hp...2010 year

• 
  @TheBatteryShop27 күн бұрын

  Thanks for the message. You can find your battery by visiting www.autobatteries.com/homepage.

• 
  @ronc414628 күн бұрын

  My project is trying to disconnect the negative battery cable in order to "reset" the transmission scheme. Will disconnecting the battery neg / ground where it is bolted to the firewall enough to clear out & "reset" the transmission scheme memory settings, or will the cable connected at the negative battery post need to be disconnected too?

• 
  @TheBatteryShop15 күн бұрын

  Thank you for watching. We would recommend consulting your mechanic or dealer for proper resolution.

• 
  @TytheBandit28 күн бұрын

  Excellent video and going step by step. Wasn’t as much of a pain taking all the coverings off after watching this. Thanks!

• 
  @TheBatteryShop28 күн бұрын

  Thank you for watching and glad we could help!

• 
  @TSAVVVV28 күн бұрын

  Just did this. And it blew the big fuse. I think my mistake was not putting back the fuse first to the terminal, I started with the black wire on the side. That may have been a ground being connected to the fuse first without having the positive side on. 😭😭😭

• 
  @TimShields82Ай бұрын

  Thank you! My car told me it needed a new battery 2hrs before I had to drive 200 miles to an airport. Fortunately got it replaced in time!

• 
  @TheBatteryShop28 күн бұрын

  Thanks for watching and glad we could help you out!

• 
  @alexs.5675Ай бұрын

  Im getting a low voltage warning after my new batteries were installed.

• 
  @TheBatteryShop28 күн бұрын

  Thank you for watchin. We would recommend to consult a mechanic or your dealer on the status of that warning.

• 
  @osamaelhawat2766Ай бұрын

  Good brevity makes sense.

• 
  @TheBatteryShopАй бұрын

  Thank you for watching!

• 
  @osamaelhawat2766Ай бұрын

  @@TheBatteryShop you are welcome

• 
  @SteveKoppel-jh9jtАй бұрын

  Thanks very much. Easy to follow. We have a car that is working.

• 
  @TheBatteryShopАй бұрын

  Thank you for watching and happy to hear we could help you out!

• 
  @MacroTh3oryАй бұрын

  I want to travel back in time and invent/patent this "Memory Saver".

• 
  @TheBatteryShopАй бұрын

  Thanks for watching!

• 
  @charlesduncan2051Ай бұрын

  I should add there is that metal plate right behind the positive terminal. Make no mistake, you WILL ride the lightning if your socket wrench connects to both that positive terminal and that metal plate. Be super careful, I don't know why it was engineered that way.

• 
  @TheBatteryShopАй бұрын

  Thank you for watching and contributing to the conversation!

• 
  @sandyj1623Ай бұрын

  Great instructional video for changing out battery in a Nissan Pathfinder. After watching this video I believe I can change the battery in my Pathfinder because it just died.

• 
  @TheBatteryShopАй бұрын

  Thank you for watching and glad we could help!

• 
  @plasboot9636Ай бұрын

  wrong battery , bevs dont need cca batterys also there was a lot of corsion some thing is wrong

• 
  @labeach101Ай бұрын

  Hi.there. my battery is sliding around, clunking around when i stop. What is used to hold the battery in place? 2014 grand overland.

• 
  @TheBatteryShopАй бұрын

  Thank you for watching. There should be a factory hold down as part of your vehicle. If you are experiencing issue I would recommend having a mechanic or dealer look at your vehicle.

• 
  @SteveTRYKАй бұрын

  Works for a 2019 - thanks!

• 
  @TheBatteryShopАй бұрын

  Thank you for watching!