Пікірлер

• 
  @unguidedone2 жыл бұрын

  it looks like you used magnesium powder with the oxidant as kn03 you got that light flash effect because kno3 is a weak oxidizer and the reaction was slow

• 
  @pauljensen87812 жыл бұрын

  Why did they stop making this model?

• 
  @vernonharris14952 жыл бұрын

  Because they are known for getting water in the hull and getting water logged. It’s shame because they were a great entry level boat

• 
  @abielgonzalez93042 жыл бұрын

  What range do you get with the 6 gallon tank

• 
  @sector76763 жыл бұрын

  I know them flat bottoms don't ride the best in semi rough conditions but how does yours do?

• 
  @jetlee7743 Жыл бұрын

  was thinking same. you could fly on cardboard on the milk pond

• 
  @sector7676 Жыл бұрын

  @@jetlee7743 I have since purchased one. I now know first hand how they ride. They're incredible boats for flats fishing/backwater. I can cruise in about 1ft of water. Performance does suffer in chop and becomes a very wet ride. As little as 15mph wind chop can make it a little uncomfortable. I love it for fishing and calm days but if I could do it over I would have went with a v-haul with more deadrise, and likely not a Carolina Skiff because most don't have enough deadrise imo. I think price would play a role as well though. Sometimes you can find these for a really good deal.

• 
  @dirkboom9603 жыл бұрын

  30-max 35 mph

• 
  @dirkboom9603 жыл бұрын

  Loved those skiffs...until i foud out that they can get waterlogged. Shame...

• 
  @don05123 жыл бұрын

  mix aluminnum powder and iron oxide at a 1:3 ratio in a 1"pipe and light a magnesium strip in the middle

• 
  @TheFonz03 жыл бұрын

  I plan to put a Mercury R series 60hp on mine but that 6 gallon gas tank I’ll have to update it to at least to a 20 gallon

• 
  @shannonreeder12374 жыл бұрын

  I can't bielive u posted this. I can I guess. That's boo boo

• 
  @greggjordan69664 жыл бұрын

  how much?

• 
  @jollygreenfishingchannel91644 жыл бұрын

  I'm a commercial spearfisherman I prefer to Carry slip on power head's that I make myself from 45 ACP-7.62x54R I prefer FMJ in all my power heads soft lead and water don't mix for good penetration mate's but great video cheer's 🤙✌️🐟🎣

• 
  @zunebuggy84355 жыл бұрын

  What is "equalibrium temperature"? Just curious.

• 
  @juletlandret63293 жыл бұрын

  Just look it up on Google 🤨

• 
  @3dvisiongamer2136 жыл бұрын

  Should have turned the pump off if u didnt, cooled it down

• 
  @drfred1203Ай бұрын

  Yup. I knew someone had to have the answer I was going to say.

• 
  @mikebiulds19156 жыл бұрын

  This is what too much spare time looks like.

• 
  @hollandkaminskiperez34446 жыл бұрын

  How are you getting 31? I only get 26 on a good day. How deep is your motor set on the jack plate?

• 
  @stonaraptor81966 жыл бұрын

  or you could just use a gun...

• 
  @sayitasitis19956 жыл бұрын

  One of the very best clean up chemicals for boat work is pure clean petrol on a clean cloth. Gets rid of scuffs, sticky tape residue, silicone messes and all sorts of nasty stuff

• 
  @terenceaddrison64606 жыл бұрын

  Anyone know how much one of these draw

• 
  @robpanama6 жыл бұрын

  This model (which is no longer available) draws about 4". The newer ones which are wider draw about the same though.

• 
  @PyroThunder7 жыл бұрын

  potassium nitrate and magnesium is a very dangerous mixture very unstable.

• 
  @codybearden30707 жыл бұрын

  i bet most of the views are from stoners looking up ways to make pipes lol

• 
  @butchlillo30257 жыл бұрын

  cody bearden hell yea hahhahaha

• 
  @ryanheilker45767 жыл бұрын

  cody bearden yup that's why I was looking....

• 
  @thatskinnydopeboyfromsomes31456 жыл бұрын

  That's why I'm here lmao

• 
  @PrashantAnnamalai6 жыл бұрын

  ya im actually looking for how to create an indent inwards of a glass bottle so i can attach a shooter with a grommit that goes straight in; for a bong

• 
  @robertdeschu43675 жыл бұрын

  I literally just made six bongs watching this gave me a very good idea though 🤔😈

• 
  @fredfrenchy7 жыл бұрын

  I want to melt some Glass just a little too distorted how can this be done for a Windows

• 
  @robp.75947 жыл бұрын

  I've since learned you can do it in the oven. About 350F and let it "slump" and it won't char the label. Takes several hours and then just shut the oven off and let it cool down slowly. (i.e., don't open the oven) In total about 24 hours. But this just produced a "flat" bottle, not the same as I was going for in this vid.

• 
  @fredfrenchy7 жыл бұрын

  Thanks - Does it bend much or can you control the bend if it is laid on some supports, like pins/metal tabs or such? also another problem with oven is it may not be big enough for 350mm x 760mm glass panes. I do have some smaller paynes so could try them

• 
  @zach30968 жыл бұрын

  lmao

• 
  @Gunpowdermaniac228 жыл бұрын

  FYI, fiberglass rots

• 
  @frankpellegrino74487 жыл бұрын

  Ryan Jefferson no, it doesn't

• 
  @liamadvena29216 жыл бұрын

  R J are u stupid

• 
  @jaimetrevino92445 жыл бұрын

  please explain.

• 
  @jeffreybabino81613 жыл бұрын

  Do you have a bilge pump installed on the boat

• 
  @jimtrotter20848 жыл бұрын

  you have to slowly heat up the entire bottle. other wise it gonna break.

• 
  @BluntForceTrauma6666 жыл бұрын

  Hahaha, _really_ Jim? If you had watched this video in it's entirety you would have noticed that the bottle, in fact, did NOT break. Even though your advice about glass may in general, be correct, waiting until you have seen the final outcome of a video before making final predictions seems to be of paramount importance if you wish to avoid appearing to be a dumbass in the future...

• 
  @nickanderkay71484 жыл бұрын

  Really it didn't? That's why it popped and he said welp it shattered experiment over.... who's the dumbass?

• 
  @aydenbomer-beach33898 жыл бұрын

  i already tried it before I watched this and the glass just broke

• 
  @witra883 жыл бұрын

  Maybe because the heat transfered too fast, same principle in sous vide cooking

• 
  @Bignardo189 жыл бұрын

  How much was this or does it cost now I need one that will work with a gopro hero 2

• 
  @cvshorty119 жыл бұрын

  Any fish on this?

• 
  @The2012waiting9 жыл бұрын

  We have a DLX1655 and run a Yamaha T50, it does about 33-35 but its almost always loaded. Not sure bout your but the front and back decks do have wood in them. Not the hull but the decks, they are options.

• 
  @robp.75947 жыл бұрын

  You are indeed correct. I learned the front deck was with plywood encased fiberglass when I mounted my trolling motor. Still lovely built boat though.

• 
  @5150roc10 жыл бұрын

  This stuff works wonders. However, one must be careful when using it along the outside of a boat, especially on any color, because fading WILL occur. If it doesn't come off with just a light rub, stop and make sure its not causing a fade mark. Don't press too hard, take your time and use a light rubbing action. If you do experience some fading a quick rub-on rub-off wax will help, but it may require some buffing and the end.

• 
  @evolve74910 жыл бұрын

  Would this be safe to use on a polyethelyne kayak?

• 
  @jdavisson5710 жыл бұрын

  not having a barrel greatly reduces 7150285power

• 
  @715028510 жыл бұрын

  wtf? That .357 magnum didn't even penetrate the plywood?

• 
  @robp.759410 жыл бұрын

  I doubt it would have done plywood even, but that was a 2x6. Didn't even hardly make a dent in it though.

• 
  @715028510 жыл бұрын

  ***** is it because there's no barrel in the powerhead? Otherwise a .357 magnum from a revolver regardless what kind of bullet it has it will penetrate that 2x6 with no problem

• 
  @robp.759410 жыл бұрын

  It is partially the no barrel thing but the biggest factor is that the water robs the energy so fast.

• 
  @715028510 жыл бұрын

  ***** well if the bullet (cartridge) is already an inch or less away from the wood, it shouldn't matter because it's not like you're shooting from above water surface into water or shooting underwater and trying to hit a target yards away.

• 
  @thecooldude61510 жыл бұрын

  Cool

• 
  @astrialkil10 жыл бұрын

  you may get less thermal shock if you put a heat lamp above and below the bottle so the whole thing is hot to start then you could turn off the propane with less fear of it cooling too fast.

• 
  @MrNick-10 жыл бұрын

  @THESOUTHERNBOY49 I have a 14' carolina skiff with a 25HP... It picks up enough speed to plane but I really need something faster, cant wait to put a 40HP on the back. You wouldnt like the max speed if you were to put a 20HP on a 16' skiff.....I love my flatbottom skiff!!

• 
  @aperson49337 жыл бұрын

  20hp on a 16ft skiff would be about the same speed as this boat.

• 
  @robp.75947 жыл бұрын

  40 is about the limit, it walks sideways on a hard turn. Gets a bit sketchy at full speed.

• 
  @robp.75947 жыл бұрын

  Not so my friend.

• 
  @robertroemer650510 жыл бұрын

  BE CAREFUL. Magic Eraser is ABRASIVE and will damage fiberglass/gelcoat.

• 
  @larryburton362410 жыл бұрын

  Coming to a bedroom window near you soon...... (G) Gee, I guess when we're skinny dipping in the pool now, we have to listen for the buzzing.... (G)

• 
  @yesicanhula806210 жыл бұрын

  nice way to make a pipe!

• 
  @thecooldude61510 жыл бұрын

  Cool

• 
  @llamapalooza10010 жыл бұрын

  i dont think it would go very far because of the weight on the end. I would also think that even if it could go, it might not have enough "oomph" to make the catridge go off.

• 
  @dyoung184410 жыл бұрын

  Ahhh. That's why the pump was there...Lol I feel dumb now. I was like who the hell does this guy think he is that's not safe hahaha. Lol Cheers you're fine didn't think it through as far as you did haha.

• 
  @jacobdecosta914711 жыл бұрын

  wrong glass

• 
  @adamgilliam972111 жыл бұрын

  Magic eraser is a micro abrasive, good for molded plastics, beware on fiberglass gelcoats it will remove the gloss with over use

• 
  @basket109911 жыл бұрын

  You could just throw it in a fire pit

• 
  @dav3fk11 жыл бұрын

  you don't need to. You need one of those bottles (like the old sobes) with a little ratchet shaped indentation on the bottom. You put a nail in the corner and whack it with a hammer, harder and harder, until it knocks the inside out of the corner of that little dimple.

• 
  @mikeinwtby11 жыл бұрын

  You can't just give up! Each failed experiment brings you closer to success. Do more!

• 
  @GunnarTh3Azul11 жыл бұрын

  i did lampwork in highschool and cracking seemed to be a recurring theme if there was any air getting to it. rather than just a vacuum, i bet this woulda been a cake-walk if you buried the bottle in some sand to absorb the heat. it may take longer, but it would cool MUCH slower allowing you to put the hole in it, and not have hairline cracks. i looked up your video while thinking of plans for my day of the dead tequila bottle bong. ENJOY

• 
  @localfuckingized11 жыл бұрын

  wooooo vandals

• 
  @vahakna11 жыл бұрын

  I did on light bulb it sounded pop in

• 
  @dylanbaine75011 жыл бұрын

  use a wine bottle with a dimple on the bottom where it goes up inside the bottom of the bottle a little, and just hold it ontop of a steel bar or something and tap it on the ground.... glass waterfall....