would someone could help me please, mine dont work on cold cycle mode its always use hot water
@RaStro-sl4fg26 күн бұрын
Am getting an OL code what is the that for ? but same thing it leaves the clothes wet, so go into diagnostics and do the spin and drain like you showed, but new loads keeps stopping at OL. Any susggestions
@reginakenger5737Ай бұрын
Thank you for the very informative video. I have been struggling with the ul (unbalance mode) for quite a while. And I don’t have the means to purchase a new washer. Or even hire a repair person. You’ve saved me.
@philipvaughan4689Ай бұрын
Your video is the only one that showed how to test the drain and spin. Thank you.
@johnfowler6189Ай бұрын
Replaced the rods on my Samsung with a set of $45 rods and still had the problem until I bought a tube of Nyogel 767a dampening grease and smeared a generous coating of the grease on the rods where the bearing rides. Works great. The replacement rods don't have enough or the right type of grease on them
@WIB-72532 ай бұрын
The washer looks like Melissa
@SuzanneC-ht1er2 ай бұрын
We have BRAVOS XL that keeps having UL code show on spin cycle and still shows after trying to rebalance clothing. We have never had any work done purchased new about 8-10 yrs ago. My husband is NOT handy is ready to purchase new washer. Any suggestions I can try? What is usually cost to have technician come over to fix unit?
@falk0069Ай бұрын
Did you end up buying a new one? It probably is worth it because they things have so many issues and if you made it 10 years--not bad.
@ginareichenbach17144 ай бұрын
It actually worked!! Thank you so much!
@humbertogarcia97494 ай бұрын
Helps me a lot
@bradmelton79854 ай бұрын
Bro. What the heck happened with this problem. I have the same issue. Went trough the same steps. Still jumps around during the spin mode.
@dulcejimenez83025 ай бұрын
Mine goes good up to the last ten minutes 🥴
@rexsheeley81775 ай бұрын
great video helped me figure my pioneer out.
@MichaelJacobson5 ай бұрын
What did you do? I have a 2 year old pioneer as well that's just starting doing this exact thing. Curious how old yours was?
@falk00695 ай бұрын
For me it was definitely the compressor. It got the the point where it completely locked up. Through warranty they sent me a new compressor, but it was no joyride replacing it.
@laurenkillgore26465 күн бұрын
@@falk0069ugh I think it's my compressor too if this is what was happening to your pioneer 😭 I bought a new fan blade and motor I was going to replace tomorrow but after seeing this I might just wait and get the compressor so when I open it I'll have everything 😩
@leanidis3005 ай бұрын
went to use my 48volt SJ blower for the 4rd time this year and now won't start?!!!
@jomainemilton8775 ай бұрын
How to change out the bearings on this washer
@falk00695 ай бұрын
These Maytag/Whirlpool washers all seem the same. I watched many KZread video showing me how to do it. I recommend you watch a few and see if you are up to it. Definitely recommend the 2x4 and carjack method to get removed. You'll find several video that explain that.
@asmrbre71136 ай бұрын
What is oL error
@falk00695 ай бұрын
My understanding is "oL" is "overloaded". Whereas "uL" is "unbalanced load". I've never see the oL code, but they could be related.
@Crickmers6 ай бұрын
very helpful, thank you
@MrHanowski6 ай бұрын
You could have a bad suspension which are easy to replace.
@falk00695 ай бұрын
yep..that definitely was also one of my issues. I have a separate video that explicitly shows how to tell if they are bad.
@goo22866 ай бұрын
Thanks so much! You saved my headache! I have same washer like yours.
@joses.garcia21246 ай бұрын
I had this problem with mine and the way Got my washer to stop working. Is level my washer by fixing the problem with the hobble Legs on bottom. The only way I got it to stay level was taking the legs out and adding a locking nut to the leg and when putting the legs back in is level the washer with the level going across the top of tub not lid once level i used lock nut to tighten against the washer frame. also laid sum rubber matts on bottom of legs to help the shaking on floor. The legs on washer are the worst thing about the washer.
@outdoor_gabe85447 ай бұрын
Have same problem with a copper and hunter system
@user-tl6pv7sy2q7 ай бұрын
Thank you soooo much! This was so very helpful! I have the same washer and same problems
@backwardsmachining75268 ай бұрын
Ty so much.
@al13838 ай бұрын
Bearings in that particular washer is trash!!! I've been through 2 washers in 10 years!!
@falk00695 ай бұрын
totally agree. Also need to be careful with the cheap replacement suspension rods. They made things even worse for me.
@eienanh83878 ай бұрын
My has dL problem, can you help? What’s the problem you know? I turned on press wash, after water spray for 5 sec then DL error went on.
@falk00698 ай бұрын
As far as I know, the DL means it wobbles too much. It is very strange to me you'd see it so soon and before it even needs to spin fast. I really have no idea. Good luck.
@hoodhunter32629 ай бұрын
thank goodness I found this video. It help me found a way to spin dry our clothes. Our Maytag Bravo XL consistently failed with 14 minutes before completion (I believe right before the spinning occur, and the code is uL). I find this code to be generic and I'm still unable to pinpoint the root cause. I had a repairman came out and replaced an official Maytag suspension rod and that didn't help.
@falk00698 ай бұрын
Probably the bearings then. This washer definitely has its share problems.
@ericxxonvf10 ай бұрын
Eww why does it sound like that
@falk006910 ай бұрын
I'm planning on doing a follow up. Turns out that is what it sounds like when the compressor is about to die. Fortunately it is under warranty and I'm hoping I'll be getting a replacement soon.
@josephbauman80854 ай бұрын
Mine started making this exact same noise recently
@coolrobuxgaming11 ай бұрын
Replace the suspension rods
@falk00695 ай бұрын
that sadly was my downfall. That the was the first thing I replaced. Unfortunately, they were cheap/crappy replacements. I then replaced the bearings TWICE. Then went back to the original rods (slightly modified) and have been good ever since.
@wetfart1387able11 ай бұрын
Trying it now. Fingers crossed (2:53pm, Saturday July 29) UPDATE 2:54pm, same day): IT WORKED!!! THANK YOU!!! Fair warning: based on other videos, it’ll probably have to be tightened again, but this worked for the time being.
@jerryhill467011 ай бұрын
I am getting a control board for mine. I will let you know what happens
@falk00695 ай бұрын
control board didn't help me. It was the bearings. The crappy replacement suspension rods I got just prolonged the problem. I have a separate video on how to test the rods. Just don't do what I did and buy cheap replacements and assume they are good.
@kendrickkeeley Жыл бұрын
Hey does anyone know how to do a quick calibration on this washer? Sometimes it workes fine ... our days im plugging & unplugging
@evelynspencer6031 Жыл бұрын
I was getting an LD error code on my washer. I took out the drum, removed a hand towel from the tub and cleaned out all the hoses, checked the pumps for obstructions, and while at it, replaced the bearings and shaft since they were rusty. I'm still getting an LD error and when running diagnostics, I got an F32 error. Do you have any idea what may be going on? The washer is not draining and making a gurgling sound.
@washingandmowing15 Жыл бұрын
Sometimes socks can throw them off. in the outer tub, sometimes socks go over the rim and stay on the sides, making weight uneven.
@aprilrodriguez5874 Жыл бұрын
Wow thank you so much for this video!! I was almost going to cry because I thought I was going to need a new washer and I can not afford it at the moment. Thank you I did this and it worked !!! You are a life saver!! 😅😅😊
@Luckiekatie Жыл бұрын
Just saved us from the horrible laundry mat!!!! Ty ty ty
@ForbiddenFruit96 Жыл бұрын
I got the exact machine and its beeping and going crazy. Cant get it to work. Everytime i try to start, it resets and beep beep. We unplug it for a while and same problem
@LovingArmywife9 Жыл бұрын
Thank you so much! Question where can u find the bearing? Lol
@falk006911 ай бұрын
I just ordered a highly rated one on Amazon that match my washer. Spent about $40 on the shaft and bearing replacement kit.
@zaccheuslittlejohn5603 Жыл бұрын
Awesome Job Thank You 👍🏿🙏🏿
@minniered4115 Жыл бұрын
I want my tool belt in purple!!! I did it!!!
@MrPaknight Жыл бұрын
Don't try this unless you really know what you are doing,because you will be buying part after part and it usually doesn't fix these washers. Throw them out and save your money,time and nuckles!
@MrPaknight Жыл бұрын
I tried all this, and it's bs! The inner tub is bad and has too much play when it's stopped!
@XLDJWHAT Жыл бұрын
How do I fix a UL code?
@calebwalker5064 Жыл бұрын
so it was the bearing and shaft that was the issue then?? I just replaced my bearings, and it is still throwing the code. Unsure if I installed incorrectly or if it is the suspension rods now?
@falk0069 Жыл бұрын
For me it was just the bearing/shaft. unfortunately for me I replaced the good rods first with cheap aftermarket ones, so I ended up replacing the bearings a second time thinking I did it wrong or got a bad one. If I was you, I would do the rods as well. They are much easier to replace. Just don't go cheap like I did. And when you get the new ones make sure the foam/rubber stopper on them doesn't slide easily.
@GrandmaSezSo Жыл бұрын
You probably have a new machine by now but I'm stuck with the Bravo XL. Your spin fix works but I have to do this ever single time. IS there anything in your pamphlet that instructs how to reset it? If you still have that instruction sheet, can you photocopy and email me it?
@falk0069 Жыл бұрын
I think I still have it. I'll have dig around for it. Do you want to email me first? It is just my handle @gmail.com.
@GrandmaSezSo Жыл бұрын
@@falk0069 Thank you. I sent you an email
@falk0069 Жыл бұрын
@@GrandmaSezSo hopefully you got my email with the scan. Hope you have luck.
@Zachamation Жыл бұрын
@@falk0069I emailed you as well if you would be kind enough to respond, thank you 🙏🏻
@falk0069 Жыл бұрын
in case others would like it, I posted it here: www.dropbox.com/s/km8oizbloll9u7t/Maytag_Washer_Bravos_XL.pdf?dl=0
@tonyschol4326 Жыл бұрын
Where did you find the new bearings kit? I replaced my stabilizer rods with still the ul code. So next I’m going to do the bearings. Mine is a MVWB980BW0 tho
@falk0069 Жыл бұрын
I just pick one from Amazon that wasn't too expensive but still looked quality.
@jimc.8496 Жыл бұрын
Very helpful but wish you'd gone into detail about how you actually fixed the problem. I have the identical issue but don't know what to specifically do with the burnt wire and connection! Where does the black cover go? Where and how did you wrap electrical tape? Details, details instead of "hmmm's."
@falk0069 Жыл бұрын
Sorry. I made a bunch of mini videos for myself to hopefully share with others in case they could help me solve the problems. I then concatenated the little clips and made a longer video. The main idea is if other have the weird clicking sounds they may have the same loose wire issue. So far this winter it has been working like a champ and has been starting perfectly every time.
@GrandmaSezSo Жыл бұрын
Thanks. I have the same short-lived machine doing the same thing, throwing UL error everytime toward end of cycle. I can't afford a repairman or new machine. I really appreciate your video.
@mathewmouritsen9347 Жыл бұрын
Hello thank you for this. We can use our washer in a pinch now, but I still need to fix it for good. When going into maintenance mode in the video, it flashes"H94" and you mention it goes through error codes. Mine has the exact same code. Do you know what this is? I am thinking of replacing the bearing but want to make sure it is not an electronic problem (motherboard) that will make it worth just throwing the machine away.
@travelernextstopheaven3286 Жыл бұрын
I got a Snow job too and it's not starting at all, thanks for the video
@Bigvic5bn Жыл бұрын
I bought one brand new about a year ago and the damn thing hasn't started yet
@jstar2212 Жыл бұрын
My washer is throwing the UL code and nothing has worked. After being gone for a week I did a load and the washer is working fine. I ordered the suspension rods and am still waiting on them to be delivered. My question is if the washer is washing fine after not using for a week is the problem the rods or really in the board?
@falk0069plus Жыл бұрын
it could many things. I ended up changing a sensor, bearings (twice) and the rods. Check out my other video on how to check your new rods are actually good. I fell in the trap of installing bad ones and ended up replacing the bearing a second time when I didn't actually need to, plus the sensor which I didn't need to. kzread.info/dash/bejne/goVrmZecqK-alc4.html
@jstar2212 Жыл бұрын
@@falk0069plus ok thanks for replying. I did order original OEM suspension rods. I was just trying to save money if it might be something else.
@Hus6524 Жыл бұрын
I would buy the rods directly from maytag or whirlpool, buying them off of Amazon is just a horrible idea because, they can get damaged during shipping and if is just bad news, so I would recommend buying them from Whirlpool directly.
@falk0069 Жыл бұрын
Definitely the best, but the most expensive too. In my case the form material used on my replacement rods was garbage. You never know what you're going to get unless go with the manufacturer.
@Hus652410 ай бұрын
@falk0069 7 months late lol. But what kind of material was uses on the brand new ones
Пікірлер
would someone could help me please, mine dont work on cold cycle mode its always use hot water
Am getting an OL code what is the that for ? but same thing it leaves the clothes wet, so go into diagnostics and do the spin and drain like you showed, but new loads keeps stopping at OL. Any susggestions
Thank you for the very informative video. I have been struggling with the ul (unbalance mode) for quite a while. And I don’t have the means to purchase a new washer. Or even hire a repair person. You’ve saved me.
Your video is the only one that showed how to test the drain and spin. Thank you.
Replaced the rods on my Samsung with a set of $45 rods and still had the problem until I bought a tube of Nyogel 767a dampening grease and smeared a generous coating of the grease on the rods where the bearing rides. Works great. The replacement rods don't have enough or the right type of grease on them
The washer looks like Melissa
We have BRAVOS XL that keeps having UL code show on spin cycle and still shows after trying to rebalance clothing. We have never had any work done purchased new about 8-10 yrs ago. My husband is NOT handy is ready to purchase new washer. Any suggestions I can try? What is usually cost to have technician come over to fix unit?
Did you end up buying a new one? It probably is worth it because they things have so many issues and if you made it 10 years--not bad.
It actually worked!! Thank you so much!
Helps me a lot
Bro. What the heck happened with this problem. I have the same issue. Went trough the same steps. Still jumps around during the spin mode.
Mine goes good up to the last ten minutes 🥴
great video helped me figure my pioneer out.
What did you do? I have a 2 year old pioneer as well that's just starting doing this exact thing. Curious how old yours was?
For me it was definitely the compressor. It got the the point where it completely locked up. Through warranty they sent me a new compressor, but it was no joyride replacing it.
@@falk0069ugh I think it's my compressor too if this is what was happening to your pioneer 😭 I bought a new fan blade and motor I was going to replace tomorrow but after seeing this I might just wait and get the compressor so when I open it I'll have everything 😩
went to use my 48volt SJ blower for the 4rd time this year and now won't start?!!!
How to change out the bearings on this washer
These Maytag/Whirlpool washers all seem the same. I watched many KZread video showing me how to do it. I recommend you watch a few and see if you are up to it. Definitely recommend the 2x4 and carjack method to get removed. You'll find several video that explain that.
What is oL error
My understanding is "oL" is "overloaded". Whereas "uL" is "unbalanced load". I've never see the oL code, but they could be related.
very helpful, thank you
You could have a bad suspension which are easy to replace.
yep..that definitely was also one of my issues. I have a separate video that explicitly shows how to tell if they are bad.
Thanks so much! You saved my headache! I have same washer like yours.
I had this problem with mine and the way Got my washer to stop working. Is level my washer by fixing the problem with the hobble Legs on bottom. The only way I got it to stay level was taking the legs out and adding a locking nut to the leg and when putting the legs back in is level the washer with the level going across the top of tub not lid once level i used lock nut to tighten against the washer frame. also laid sum rubber matts on bottom of legs to help the shaking on floor. The legs on washer are the worst thing about the washer.
Have same problem with a copper and hunter system
Thank you soooo much! This was so very helpful! I have the same washer and same problems
Ty so much.
Bearings in that particular washer is trash!!! I've been through 2 washers in 10 years!!
totally agree. Also need to be careful with the cheap replacement suspension rods. They made things even worse for me.
My has dL problem, can you help? What’s the problem you know? I turned on press wash, after water spray for 5 sec then DL error went on.
As far as I know, the DL means it wobbles too much. It is very strange to me you'd see it so soon and before it even needs to spin fast. I really have no idea. Good luck.
thank goodness I found this video. It help me found a way to spin dry our clothes. Our Maytag Bravo XL consistently failed with 14 minutes before completion (I believe right before the spinning occur, and the code is uL). I find this code to be generic and I'm still unable to pinpoint the root cause. I had a repairman came out and replaced an official Maytag suspension rod and that didn't help.
Probably the bearings then. This washer definitely has its share problems.
Eww why does it sound like that
I'm planning on doing a follow up. Turns out that is what it sounds like when the compressor is about to die. Fortunately it is under warranty and I'm hoping I'll be getting a replacement soon.
Mine started making this exact same noise recently
Replace the suspension rods
that sadly was my downfall. That the was the first thing I replaced. Unfortunately, they were cheap/crappy replacements. I then replaced the bearings TWICE. Then went back to the original rods (slightly modified) and have been good ever since.
Trying it now. Fingers crossed (2:53pm, Saturday July 29) UPDATE 2:54pm, same day): IT WORKED!!! THANK YOU!!! Fair warning: based on other videos, it’ll probably have to be tightened again, but this worked for the time being.
I am getting a control board for mine. I will let you know what happens
control board didn't help me. It was the bearings. The crappy replacement suspension rods I got just prolonged the problem. I have a separate video on how to test the rods. Just don't do what I did and buy cheap replacements and assume they are good.
Hey does anyone know how to do a quick calibration on this washer? Sometimes it workes fine ... our days im plugging & unplugging
I was getting an LD error code on my washer. I took out the drum, removed a hand towel from the tub and cleaned out all the hoses, checked the pumps for obstructions, and while at it, replaced the bearings and shaft since they were rusty. I'm still getting an LD error and when running diagnostics, I got an F32 error. Do you have any idea what may be going on? The washer is not draining and making a gurgling sound.
Sometimes socks can throw them off. in the outer tub, sometimes socks go over the rim and stay on the sides, making weight uneven.
Wow thank you so much for this video!! I was almost going to cry because I thought I was going to need a new washer and I can not afford it at the moment. Thank you I did this and it worked !!! You are a life saver!! 😅😅😊
Just saved us from the horrible laundry mat!!!! Ty ty ty
I got the exact machine and its beeping and going crazy. Cant get it to work. Everytime i try to start, it resets and beep beep. We unplug it for a while and same problem
Thank you so much! Question where can u find the bearing? Lol
I just ordered a highly rated one on Amazon that match my washer. Spent about $40 on the shaft and bearing replacement kit.
Awesome Job Thank You 👍🏿🙏🏿
I want my tool belt in purple!!! I did it!!!
Don't try this unless you really know what you are doing,because you will be buying part after part and it usually doesn't fix these washers. Throw them out and save your money,time and nuckles!
I tried all this, and it's bs! The inner tub is bad and has too much play when it's stopped!
How do I fix a UL code?
so it was the bearing and shaft that was the issue then?? I just replaced my bearings, and it is still throwing the code. Unsure if I installed incorrectly or if it is the suspension rods now?
For me it was just the bearing/shaft. unfortunately for me I replaced the good rods first with cheap aftermarket ones, so I ended up replacing the bearings a second time thinking I did it wrong or got a bad one. If I was you, I would do the rods as well. They are much easier to replace. Just don't go cheap like I did. And when you get the new ones make sure the foam/rubber stopper on them doesn't slide easily.
You probably have a new machine by now but I'm stuck with the Bravo XL. Your spin fix works but I have to do this ever single time. IS there anything in your pamphlet that instructs how to reset it? If you still have that instruction sheet, can you photocopy and email me it?
I think I still have it. I'll have dig around for it. Do you want to email me first? It is just my handle @gmail.com.
@@falk0069 Thank you. I sent you an email
@@GrandmaSezSo hopefully you got my email with the scan. Hope you have luck.
@@falk0069I emailed you as well if you would be kind enough to respond, thank you 🙏🏻
in case others would like it, I posted it here: www.dropbox.com/s/km8oizbloll9u7t/Maytag_Washer_Bravos_XL.pdf?dl=0
Where did you find the new bearings kit? I replaced my stabilizer rods with still the ul code. So next I’m going to do the bearings. Mine is a MVWB980BW0 tho
I just pick one from Amazon that wasn't too expensive but still looked quality.
Very helpful but wish you'd gone into detail about how you actually fixed the problem. I have the identical issue but don't know what to specifically do with the burnt wire and connection! Where does the black cover go? Where and how did you wrap electrical tape? Details, details instead of "hmmm's."
Sorry. I made a bunch of mini videos for myself to hopefully share with others in case they could help me solve the problems. I then concatenated the little clips and made a longer video. The main idea is if other have the weird clicking sounds they may have the same loose wire issue. So far this winter it has been working like a champ and has been starting perfectly every time.
Thanks. I have the same short-lived machine doing the same thing, throwing UL error everytime toward end of cycle. I can't afford a repairman or new machine. I really appreciate your video.
Hello thank you for this. We can use our washer in a pinch now, but I still need to fix it for good. When going into maintenance mode in the video, it flashes"H94" and you mention it goes through error codes. Mine has the exact same code. Do you know what this is? I am thinking of replacing the bearing but want to make sure it is not an electronic problem (motherboard) that will make it worth just throwing the machine away.
I got a Snow job too and it's not starting at all, thanks for the video
I bought one brand new about a year ago and the damn thing hasn't started yet
My washer is throwing the UL code and nothing has worked. After being gone for a week I did a load and the washer is working fine. I ordered the suspension rods and am still waiting on them to be delivered. My question is if the washer is washing fine after not using for a week is the problem the rods or really in the board?
it could many things. I ended up changing a sensor, bearings (twice) and the rods. Check out my other video on how to check your new rods are actually good. I fell in the trap of installing bad ones and ended up replacing the bearing a second time when I didn't actually need to, plus the sensor which I didn't need to. kzread.info/dash/bejne/goVrmZecqK-alc4.html
@@falk0069plus ok thanks for replying. I did order original OEM suspension rods. I was just trying to save money if it might be something else.
I would buy the rods directly from maytag or whirlpool, buying them off of Amazon is just a horrible idea because, they can get damaged during shipping and if is just bad news, so I would recommend buying them from Whirlpool directly.
Definitely the best, but the most expensive too. In my case the form material used on my replacement rods was garbage. You never know what you're going to get unless go with the manufacturer.
@falk0069 7 months late lol. But what kind of material was uses on the brand new ones