Пікірлер

• 
  @Raj-mz4eh9 күн бұрын

  Thank you for taking the time to make this video. I followed all the steps in your video. Cleaned, vacuumed and used fine sandpaper on the three rods. I didn't really do anything significant but it has been a week now with no more error code 12.🤞

• 
  @gregtrende829011 күн бұрын

  I did this swap on my 2003 500 Sportsman. Worked perfectly! Thank you!!!

• 
  @vitalijjurt810715 күн бұрын

  Is it mono or stereo?

• 
  @jeffwilliams31217 күн бұрын

  If the engineers ever had to repair anything they designed things would be different

• 
  @mangotwissАй бұрын

  Rheen SUCKS! JUST TWO MONTHS AND CODE 12 ERROR.. wondering if I can return this shitty item back to Home Depot

• 
  @billk333Ай бұрын

  they must have listened to you. I just purchased a new Impeller. It was $189 and didn't come with any housing or frame..

• 
  @TheSoundmanPete2 ай бұрын

  If it doesn't start on the 2nd pull... you need to let the compression equalize before trying again or the kickback will take your arm off. Those tires are known for leaking Very easy to snap off those valve stems. The tires come off the rim easily. However the rim must be clean ans smooth or it will leak. Based on the engine serial number... some used a gasket and some used form a gasket.

• 
  @TheSoundmanPete2 ай бұрын

  A second Sutech video. Awesome. Another helpful hint. It's 99% impossible to fill that gearbox with #30 motor oil. Put the 6 oz of #30 oil in a pull-out spout oiler. Makes the job extremely easy.

• 
  @TheSoundmanPete2 ай бұрын

  I can give you a lot of helpful hints. Leaking tires and tires off the rim are common problems. Sometimes a tube is best. To get the tire in your video to reseat.... you take a a ratcheting strap and put it in the center of the tire and crank it a few times. A quick shot of air should reseat the tire. Don't overfill with strap on or it won't come off.

• 
  @ScrapMetalWorks2 ай бұрын

  Thank you for the advise. I think I managed to figure out the transmission oil amount and how to fill, engine start is not a problem. the last item I haven't resolved are the front tires. I did manage to re inflate them but they go flat again and quickly. I would like to put in tubes but I have not been able to find them them small enough for those tires. Would you know what size and perhaps a source? Thx

• 
  @TheSoundmanPete2 ай бұрын

  Good to see another Sutech video. There are several guys that have posted videos with dedicated problem resolutions. I have one that I've done a lot of work on. Maybe we can help each other. I do have all the manuals but mine is not electric start. The gearbox uses #30 non detergent oil.

• 
  @egidijuspakstas28642 ай бұрын

  what to do if after changing the motor the robot does not move around the apartment but just rotates in one place?

• 
  @ScrapMetalWorks2 ай бұрын

  I had this issue and I though it was the speed of the motor but it turned out to be the direction of rotation of the motor which is not the same from motor to motor. So just switch the red/black wires of the motor and try again.

• 
  @egidijuspakstas2864Ай бұрын

  @@ScrapMetalWorks Thank you. I will try to replace the wires.

• 
  @derekobidowski33012 ай бұрын

  I done a predator 212cc swap or repower10 years ago on my Cyclone Rake Commercial as i used the Rato non Hemi engine as the muffler was my problem as i used a elbow off a junk 208cc snowthrower engine as i had to cut and bend the muffler pipe and add a muffler deflector as its what i did at the time as today i should get a Briggs & Stratton XR950 muffler with the wire shield and deflector from Jack's small engines as they are $69. same thing if you put in a Honda GX200 commercial grade engine the muffler is the problem as taryl fixes all calls it the Muffkin. watch his video Trac Vac engine swap won't fit big problem. it shows how he modified a hemi 212cc engine to fit a Trac Vac to replace a worn out Briggs & Stratton Intek engine. My Cyclone rake was a tecumseh engine as it had carburetor issues as Tecumseh is no longer in business and the parts are no longer available as its not worth repairing the engine as the predator engine is the cost effective way to go. as today Cyclone Rake only gives you a Briggs & Stratton XR950 208cc engine as its problems a plastic camshaft and the compression release goes out on it as the predator 212cc is the way to go if you get the Briggs & Stratton XR950 wire guard muffler and deflector for the Cyclone Rake application as well as the Agri Fab vacs

• 
  @petersohl58333 ай бұрын

  Where can I get the shaft adapter parts

• 
  @SF-fm7ov3 ай бұрын

  If the spacer is worn or too short add washers like @glowell did in the comments to help lock shaft to inner race. If the end nut is only tightening the washer on to the end of the shaft, then spacer is too short. It is the squeezing of the nuts on the shaft ends that locks the pulleys and spacer to the inner races and the key locks the shaft to the pulley. Therefor, LOOSE END NUTS or SHORT SPACERS ALLOW SHAFT TO TURN INSIDE THE BEARING! Hope this helps someone. First try tightening the end bolts with an impact or add washers and you shouldn't have to resort to this.

• 
  @danielwillett71643 ай бұрын

  What are the torque specs for the the oil drain plug and the oil filter drain plug?

• 
  @ShadrakhYehochanan3 ай бұрын

  Surely it would be possible for me to add several switches in parallel to the same board if I wanted to monitor for example several hydrophonic plants in one location?

• 
  @davebenedict79863 ай бұрын

  The bar at the back end of the scoop to meet the blade is a good idea. You could weld a doubler on the front 1.5" of the scoop to reinforce that.

• 
  @rrahmanlloga66013 ай бұрын

  I am a plumber and I hate when people put this in. Old gas tanks are brilliant. 7 years of use pay $500 for replacement two parts and you good for another 7 years.

• 
  @ScrapMetalWorks3 ай бұрын

  Unfortunately a new water heater costs more than $500 times specially with the forced vent plus labor to install of course. But more importantly an always on water heater consumes a lot more fuel than tankless as it is always on even during the day when hot water use is little to none. Yes the tankless are more expensive but long term more cost effective.

• 
  @jaycumiford80623 ай бұрын

  I see this video is about three years old now, how is the PVC holding up? Is it possible to go to a smaller diameter of pvc pipe so I can streamline the table a bit? I think you did a great job with it.

• 
  @ScrapMetalWorks3 ай бұрын

  The PVC pipe is working great. Like I said before you can stand on top of schedule-40 PVC pipe without any issue with the force concentrated on a small section. Same concept here so no issues. Yes you could use a smaller section but I wanted to feed the extension cord without cutting it so that could be a consideration. Also a smaller diameter may be a more flexible than the 2” so brace it inside the flip top just past the opening so the section that turns is nice and rigid. Thanks.

• 
  @jaycumiford80623 ай бұрын

  @@ScrapMetalWorks Thank you, good info!

• 
  @frankmartin49834 ай бұрын

  I have three different codes at different times. I have the same process to do as well. The only different thing that Rheem recommends is to clean the orifices with a wire but not to break inside the orifices. There's a brass nipple at the end of orifices. That one is for code 13. That's the problem I'm having. Rheem says to clean all of them with a wire, especially the brass nipple. Hope this helps for anyone out there. I will try also. Great video

• 
  @johneverett22714 ай бұрын

  Nice station! For preventing the legs from folding, you could drill a hole through the plywood and leg below the pivot bolt, maybe 2 inches down. Then you can slip a retaining pin through the ply and the leg. You could even go so far as to get lynch pins that can latch in place when installed. Add a retaining strap/cable to each, and you will never lose them either.

• 
  @amandaschowalter4 ай бұрын

  Promo'SM

• 
  @FlakJakIt4 ай бұрын

  I watched the video, but don’t have the means to make this exhaust extension. Is there anyway I can purchase one made from you? Thank you

• 
  @smlakergirl4 ай бұрын

  Same!

• 
  @nadreggid5 ай бұрын

  Great vid. Hey, why can't the safety plastic thermo sheets be replaced? I have a nice heater with one burnt spot that I have heard I must just throw away. That hurts my feelers.

• 
  @msce2205 ай бұрын

  I also had the same problem some days after I replaced the broken o-ring of the side brush. The robot always tried 3 times to start and I got an error with a red led light. I saw that the lidar didn’t turn. So I thought about replacing the flat cable from the motherboard to the lidar or the lidar motor or the big lidar o-ring. Because of that I wanted to find out if the lidar motor turns and just the o-ring is worn. So, I started the robot without the main cover. The lidar didn’t turn. So, I tapped it with my finger counterclockwise and it started to turn again. Now the robot works again without replacing anything.

• 
  @JeanPhilippeJodoin4 ай бұрын

  Thank you, that actually did fix it for me! Just lightly moving it got it unstuck.

• 
  @mattalki5 ай бұрын

  I'm working on the same thing for our 2014 Beetle right now. Have you shared the 3D print file anywhere so we can also print a crispy new USB panel? TIA!

• 
  @ScrapMetalWorks5 ай бұрын

  Just posted on Thingiverse: www.thingiverse.com/thing:6448071

• 
  @mattalki5 ай бұрын

  @@ScrapMetalWorks Thanks! I appreciate it!

• 
  @guylast95165 ай бұрын

  Thanks for the video. I want to get this done but have a different take if you allow me. Recently set up quite a few leak sensors to detect leaks and so used one for my aquarium to keep an eye on my top off pump dumping water in it. The only issue is the leak sensor is splashed so often with water from air bubbles and fish themselves. I was thinking what if I snip off the leak sensor from the hanging type end and attach the float sensor to it. i havent considered power requirements etc here at all. Just a thought....

• 
  @pikpokpikpok48296 ай бұрын

  How many liters oil?

• 
  @SaschiIein6 ай бұрын

  240p - really?

• 
  @TylerHankss7 ай бұрын

  Links to any of these added parts?

• 
  @frankposterello16287 ай бұрын

  any leaks or problems from having taken the pump off? I'm about to do this and is very helpful, thanks.

• 
  @ScrapMetalWorks7 ай бұрын

  No leaks. Just make sure the gasket dries for at least 12hrs before putting oil back in.

• 
  @86FxBdyCpe7 ай бұрын

  I know you have a lot of time invested with the muffler. But I believe a muffler from a B&S OHV (Honda clone) fits. In fact, all new current Cyclone Rakes come with a B&S XR-950 engine.

• 
  @ScrapMetalWorks7 ай бұрын

  Oh yeah I see that now and the aftermarket are only about $20. The intake pipe is curved more than the original effectively moving the muffler closer to the spark plug and making it inline with the engine side where the shaft is which was my problem. My modified pipe works fine now and no point in changing it but good to know. Thanks!

• 
  @billwinick98657 ай бұрын

  Nice to see someone has come up with a solution to this. Are you willing to post your stl or make available?

• 
  @Darkblade32877 ай бұрын

  The burner burns low stage whenever there isn’t a large demand of hot water. The other side of the burner relights whenever the demand increases/high demand

• 
  @89vette17 ай бұрын

  I had a code 11 and it turned out to be clogged gas manifold ports. Rheem techs never mentioned this to me or the installer. Works great now. Unit is 7 years old and heats the floor in my garage. Rheem techs should have known. Kept telling me to replace parts even though they diagnosed fine.

• 
  @lothianmcadam17 ай бұрын

  Where did you find the replacement ribbon cable?

• 
  @frankposterello16287 ай бұрын

  Great series! Thanks for documenting it so clearly - I just bought that same tractor - everything still working but really tired and dirty with 800+ hours. So probably will do the same job. Glad you got it all figured out, and perfect timing for me.

• 
  @dmacfarm7 ай бұрын

  Thank you for this explanation. Helped me fix my machine with the same issue. Back and ready for the winter.

• 
  @DrTENFAISPAS7 ай бұрын

  Thanks for your time sharing the troubleshooting steps. I had the same low water pressure when brewing. I descalled, no success. I replaced 1 small broken o ring in the orange cylinder, no success. I disassembled the water pump pressure relief valve, nothing looked wrong or dirty but after putting it back together my issue was fixed! A correct brewing pressure was back. After hours of investigation it feels so good. I hope it helps. Good luck folks.

• 
  @oshaosha73388 ай бұрын

  Hi, I am not sure if the LiDAR on my D7 is spinning or not. It spins when I push it with a Q-tip but doesn’t spin on its own when I run the machine.

• 
  @ScrapMetalWorks8 ай бұрын

  Then maybe it’s just a worn belt. I would replace that to start

• 
  @user-em1sj5ph6h8 ай бұрын

  Harbor Freight wheels. Got 2 just like them.

• 
  @ScrapMetalWorks8 ай бұрын

  Don’t use Harbor Freight wheels as they broke very fast. I ended up getting them from Tractor supply at double the price but worth it as they are much stronger and turn better.

• 
  @user-em1sj5ph6h8 ай бұрын

  I’m at about the same spot as you are on making mine. I’ve too many irons in the fire.

• 
  @ScrapMetalWorks8 ай бұрын

  It works great!

• 
  @Bloo-Falkon13458 ай бұрын

  is that relay something you added or is it already in there behind the high beam? do you sell those shims for the lights? I have the exact same lights for my low beams. Thanks.

• 
  @Stinkmonkey248 ай бұрын

  what are those lights called, i need to buy them

• 
  @ScrapMetalWorks8 ай бұрын

  Amazon: LED Pods, Lumitek 2PCS 36W 7inch

• 
  @twsmith65989 ай бұрын

  We have had our D7 for 4yrs now and basically when this happens we remove the battery and reinstall it. This forces a TRUE power cycle of the device and it works again for a month. Then its wash rinse repeat.

• 
  @dennishunt5197 ай бұрын

  Did not work for me 😢

• 
  @wizard1701a10 ай бұрын

  Thank you!!

• 
  @hylomane10 ай бұрын

  It's amazing to watch your over complicated mods that end up breaking your tractor in a new way.

• 
  @Mega1963196310 ай бұрын

  Por favor podria informarme donde consigo esa herramienta comprar mas exactamente

• 
  @CyclonesWorld10 ай бұрын

  I was losing my mind. Replaced the motor and still didn't work. Finally got frustrated and started searching online and found your video. Sure enough, I checked my ribbon cable closely and found that it was damaged. Looks like it heated up and melted, probably from the bad motor.

• 
  @rockiemountin753511 ай бұрын

  I have the same tractor with the same problem,that thrust bearing wouldn’t last long on my tractor it gets so dusty every time I mow the lawn then I hose the tractor down to remove the dust,great video just the same thanks for posting