Пікірлер

• 
  @dave8826Күн бұрын

  Did you fix the wi fi module and the camera works?

• 
  @fixingmoddingbuildingКүн бұрын

  Yes, but not always the fix

• 
  @ssnazirifulКүн бұрын

  Thanks gotta do mine this weekend heater smells weird

• 
  @Astrolucks762 күн бұрын

  Did this but I power on and switch is making small buzzing noise 😔

• 
  @fixingmoddingbuilding2 күн бұрын

  Check your solder, if no joy reset and test without.

• 
  @wolvrG2 күн бұрын

  Can we use Lite pico2040 modchip in v1 model?

• 
  @fixingmoddingbuilding2 күн бұрын

  I think there's work arounds running cables but I don't know how

• 
  @nik_22053 күн бұрын

  does this work for v2 chips too?

• 
  @fixingmoddingbuilding3 күн бұрын

  Yes

• 
  @hannoverfisst24143 күн бұрын

  You lost me here. At 15:00 you soldered one end of a green wire to the pad you placed under the nand. Then at 18:00 you soldered the end of a green wire to a point on the circuit board. Then at 18:45, you soldered ANOTHER green wire to the mod chip?? Then at 19:30 you say to solder on the 'B' wire. But since you used green wire for all connections, it's not clear which green wire goes where? You really should color code when making videos or add better notes. It also looks like you're using thick plumbing solder instead of electrical solder, which is why your solder keeps globbing up.

• 
  @liduardo3 күн бұрын

  jajaja, Tronixfix....

• 
  @Fzero14533 күн бұрын

  How do you make sure not to burn the plastic from the switch Case? I got my soldering tool too close to it and burnt quite a big part off the case off.. Does kepton taping it help?

• 
  @fixingmoddingbuilding2 күн бұрын

  It's not really anywhere near the edges so shouldn't be an issue?

• 
  @Fzero14532 күн бұрын

  @@fixingmoddingbuilding From what I see in the video your connection points are sideways, mine are above and below the little point that needs to be soldered, so I guess I'm soldering closer to the case when soldering the lower copper part. Also my soldering tool is wireless and quite chunky.

• 
  @fraz82243 күн бұрын

  Все четенько показал, благодарю .

• 
  @AlexanderSandoval-r5l4 күн бұрын

  Can you please share the amazon linm

• 
  @fixingmoddingbuilding4 күн бұрын

  in description

• 
  @TapticDigital4 күн бұрын

  Pads? Who needs ‘em!

• 
  @fixingmoddingbuilding4 күн бұрын

  This fella, apparently!

• 
  @TapticDigital3 күн бұрын

  @@fixingmoddingbuilding beautiful jumper work by the way!

• 
  @fixingmoddingbuilding3 күн бұрын

  @@TapticDigital Thanks, I need more practice to smarten them up next!

• 
  @tomm61374 күн бұрын

  Nice to hear you talking, good informative video as always!

• 
  @fixingmoddingbuilding4 күн бұрын

  Thanks for the comment, decided it was time to talk, hopefully can get better over time!

• 
  @SjorsMaster5 күн бұрын

  looks like this calls back to Chinese servers, personally I wouldn't trust that

• 
  @fixingmoddingbuilding5 күн бұрын

  Is that a fact or a guess?

• 
  @HenBoe4 күн бұрын

  @@fixingmoddingbuildingCan u see what’s happening at home in the app, when u aren’t at home?

• 
  @user-tu1uw7hq9c5 күн бұрын

  where can i get the modchip from?

• 
  @fixingmoddingbuilding5 күн бұрын

  Aliexpress

• 
  @328450J5 күн бұрын

  I dont have yellow tape can i use foil instead

• 
  @fixingmoddingbuilding5 күн бұрын

  Yes

• 
  @328450J5 күн бұрын

  @@fixingmoddingbuilding thanks man great method btw I subscribed

• 
  @JamesMac-gj3fi6 күн бұрын

  Nice fix pal. You have got loads better at trace repair now. You never used to like doing trace repair.

• 
  @fixingmoddingbuilding5 күн бұрын

  Thanks and yes I tried it a few times in the past and just could not do it. Having something to zoom in good and a fine tip soldering iron also helps alot!

• 
  @shouichihayase196 күн бұрын

  If you hit copper wire with a hammer and stretch it, you can make something？

• 
  @fixingmoddingbuilding5 күн бұрын

  Nice one 👍

• 
  @za_91186 күн бұрын

  How do you rip a ribbon cable that's inside of a Nintendo Switch

• 
  @fixingmoddingbuilding6 күн бұрын

  When you have a test housing that gets a new motherboard in and out constantly, the cables get worn

• 
  @normanwestern94506 күн бұрын

  150 vs 35 dollars for slightly worse quality is a win in my opinion.

• 
  @fixingmoddingbuilding5 күн бұрын

  Yes I agree, she still plays with it now. Had other sets since and I still think it's a good deal for people on a budget!

• 
  @corykristy25947 күн бұрын

  I got a set of these I loke them but even tured off they drained the battery in matter of a day or too!

• 
  @C00LSH4RK10 күн бұрын

  Thanks, which tool i need to check if the solder is soldered correctly

• 
  @fixingmoddingbuilding10 күн бұрын

  You just look at your solder joints and see if they are done right?

• 
  @PossumB18210 күн бұрын

  Withoput image stabilisation, the images are useful for a quick look, but not suitable as a microscope. First camera does not have a close up lens.

• 
  @fixingmoddingbuilding10 күн бұрын

  Yer I have a use for the better one will be using it in future videos

• 
  @i.e.210 күн бұрын

  What should I do after the modchip?

• 
  @fixingmoddingbuilding10 күн бұрын

  kzread.info/dash/bejne/pZWrprKAesnJnJM.htmlsi=WyEynOR5rygj8e0T

• 
  @miki82ification11 күн бұрын

  glue 🤦‍♂

• 
  @fixingmoddingbuilding11 күн бұрын

  yes, glue..

• 
  @Lavadawg11 күн бұрын

  Thank you, i was shopping for a camera on aliexpress and cannot make a choice just yesterday! Are we all hobbyists on the same wavelength

• 
  @seductivepoetryinc11 күн бұрын

  ~ The rainbow 🌈 Gay Boy camera for $3.99 Hhhhaaaaa!!!

• 
  @joeceretti909811 күн бұрын

  i ashuum it's just a qr code to scannon.. just get past the activatedok a few times. to be fair it's not amazing glitches are ok though just non decide

• 
  @onelinkgadget12 күн бұрын

  Im using a 2.73 firmware

• 
  @juanjoviciana615212 күн бұрын

  Maravilloso 🎉🎉

• 
  @postenebraslux12 күн бұрын

  The song is a banger!

• 
  @PossumB18212 күн бұрын

  Good job. Could have installed in a more 'exotic' shell since you have gone to all the trouble? eg Transparent, Pokemon or Animal Crossing?

• 
  @fixingmoddingbuilding12 күн бұрын

  I am getting that many Switchs I need to try and sell some, I have found the more "exotic" ones like Pokemon just dont sell?

• 
  @averagephlogfan647512 күн бұрын

  3:40 is it easier to just remove it? I would have at least considered a haur dryer if i don't have a heat gun

• 
  @fixingmoddingbuilding12 күн бұрын

  I did remove?

• 
  @averagephlogfan647512 күн бұрын

  Nintendo switch repair is so nonsensical "Touch screen doesn't work because of a bad cartridge port" huh? Also annoying because it uses two different thermal pastes

• 
  @fixingmoddingbuilding12 күн бұрын

  Yer, thanks!

• 
  @juanjoviciana615212 күн бұрын

  loooove that music ! Friend where can donwlooad flash archive for rp2040 v4 ¿

• 
  @johncarr345812 күн бұрын

  nice fix

• 
  @fixingmoddingbuilding12 күн бұрын

  Thanks mate 👍

• 
  @guigmfrota13 күн бұрын

  First😊

• 
  @fixingmoddingbuilding12 күн бұрын

  Yes you are!👍

• 
  @alnokencanaputra125313 күн бұрын

  Hey there! I have the same problem too. I wanna ask bout the ribbon, what kind of the ribbon cable should i buy? Because here in Indonesian local online marketplace, i found 2 different type of that. It says there's are One-way cable and reversible cables. So Which one should i buy?

• 
  @skrilla.scratch13 күн бұрын

  These work with v2?

• 
  @fixingmoddingbuilding13 күн бұрын

  Not sure, I've read no, but best check there website

• 
  @skrilla.scratch13 күн бұрын

  @@fixingmoddingbuilding I ordered 3 after posting, I reached out to site on delivery time and what their confirmation was for v2. I'll reply when I get em.

• 
  @shawnchalfant159514 күн бұрын

  Works, but sloppy

• 
  @fixingmoddingbuilding14 күн бұрын

  🤣🤣

• 
  @Legendarytheanimator14 күн бұрын

  which laptop is this?

• 
  @fixingmoddingbuilding14 күн бұрын

  Just an old dell

• 
  @Legendarytheanimator14 күн бұрын

  @@fixingmoddingbuilding is it dell inpiron 13 7359

• 
  @fixingmoddingbuilding13 күн бұрын

  @@Legendarytheanimator yes

• 
  @44.caliberbrainsurgery6314 күн бұрын

  Man, I guess my flex cable was bad or something. I redid everything and it just kept booting into ofw with there being 2 pulses on the chip. I just uninstalled everything and at least the switch boots fine. I'm gonna try with the other flex cable and see if it works better, otherwise I need to try direct wire install.

• 
  @fixingmoddingbuilding14 күн бұрын

  Good luck 👍

• 
  @pac-man-ooo552014 күн бұрын

  Is that ribbon wrap up and place on the battery made for the scuff?

• 
  @stachu458715 күн бұрын

  You can use capton tape to cover caps in between so you dont short them

• 
  @fixingmoddingbuilding15 күн бұрын

  Yer heard someone say that before, it's a good tip

• 
  @user-du5lt5ij7h15 күн бұрын

  Good to hear your voice!As always love your vids.

• 
  @fixingmoddingbuilding15 күн бұрын

  Thanks, decided to bite the bullet!

• 
  @fixingmoddingbuilding15 күн бұрын

  Thanks, decided to bite the bullet!

• 
  @jwill799815 күн бұрын

  Thanks, meng. Every other video told to use a magical toothbrush, but adjusting tightening the ribbon did the job.

• 
  @fixingmoddingbuilding15 күн бұрын

  Thanks, glad it helped 👍

• 
  @fixingmoddingbuilding15 күн бұрын

  Thanks, glad it helped 👍

• 
  @josemariatrindadejunior170316 күн бұрын

  i have done on 3 v2 switches, one of them I slipped in the wifi capacitor on the left side of the shield that you have to remove, it was a headache to solder it again, but it worked!, im training to do on OLED systems, one day I will do it!

• 
  @BurritoMaster16 күн бұрын

  Help my wii u keeps turning off when I plug the pico to the wii u

• 
  @Quickdrop_17 күн бұрын

  Zoom in more so I can’t see shit

• 
  @fixingmoddingbuilding16 күн бұрын

  Will do 👍

• 
  @JuanGomezYT17 күн бұрын

  Every listing in Ali Express I see do not seem to have the SP1 and SP2 flex cable, anyone knows why?

• 
  @heraldmigaildhramosm.212617 күн бұрын

  Ídem

• 
  @fixingmoddingbuilding17 күн бұрын

  The lite comes with one version

• 
  @biswashrai55418 күн бұрын

  If i loose golden part on flex while soldering does the flex wont work?

• 
  @fixingmoddingbuilding18 күн бұрын

  Yer probably won't work as that's the solder point