NOT recommended to lift the Limited with the Quadra-Drive 4x4 system!
@areject172 күн бұрын
This Jeep looks sweet!!! When you show the Jeep at the end is this with stock tire size? I really like the look of it with that wheel and tire set up! Thanks for sharing!
@klaatu215 күн бұрын
Why is the right most CAM 180 degrees off? The "UP" is pointing down
@seandann816320 күн бұрын
Great video, thanks for posting! I just purchased the same Rough Country 2" Lift Kit for my '04 Grand Cherokee. Can you please confirm that the rubber rear lower coil spring insulator is not required when installing this Rough Country Lift Kit?
@JesusFlores-gf4guАй бұрын
31”?
@JesusMendozaCoversАй бұрын
awesome
@josephbuzzard9360Ай бұрын
What size wheel spacers are you using
@minamusiklistor93192 ай бұрын
Why not put a new rubber springisolaror on the rear springs? Now it's metal on metal!
@nadakeenr77153 ай бұрын
did you have problems with stock springs falling out or bowing out after the kit installation?
@cloubert013 ай бұрын
Does this increase ground clearance? And can it be used in a quadratec?
@CozyBear_2926 күн бұрын
Rough Country website says No on the Quadra -Trac
@only1muppet3 ай бұрын
According to Alldata the exhaust cam, the one in the back, is supposed be a half tooth below the front one. Yours looked to be the opposite, I’m wondering if that was accidental or intentional? You should’ve covered finding TDC for the #1 piston, just showing you spin the crank to line up the mark could cause someone to need to redo all that work.
@chestrockwell70234 ай бұрын
These kits are a waste of time and money....first of all if you put this kit on a older jeep your not getting a 2 inch lift cause the stock springs are shot so you need new ones. Save up some cash and buy a 4 inch lift kit that way it's a whole new suspension at the height that looks badass 🤘
@Raid-qx4jv15 күн бұрын
I put 2.5 spacers on my 04 and honestly if ur not hitting trails to hard and just want some height then spacers are a good alternative
@franconunez13594 ай бұрын
Estoy haciendo los mismo en mi wj que amortiguadores colocaron ? Muchas gracias
@Lu-e4 ай бұрын
Doesn’t sound aggressive
@shesqueeledАй бұрын
prolly has gay catalytic converters
@dubs4life74 ай бұрын
Ok, talk to me here. How close to stock quite is it getting? I need my car (B6 A4 Avant 1.8t) to be reasonable sounding for my sanity, but I don't want complete sad stock exhaust. I got the car with a 3 in turbo back and same bullet style junk.... stupid loud. Would you say this is "closer to stock" but obviously still makes some noise? Also, it seems quite at idle, but decent at full song, can you confirm that? Thx
@longgoneg604 ай бұрын
I had this exact same setup on a mk5 gti (2.0t) and ended up installing a 16” resonator in mid pipe to keep the drone down at highway speed. The gti is a much shorter car than a B6 so Id recommend you look into a slightly longer resonator to bring the decibels down but still have a sporty sound when accelerating. Resonator is a much cheaper option and easier to install in a straight section.
@dubs4life74 ай бұрын
What resonator did you add? I had a vibrant UQ on my mk5 rabbit. It did pretty good, just curious what worked for you.
@jackstandnation2 ай бұрын
The car has 2 other small glasspacks in it (no cats). They just act as resonators. It sounds a lot better with the new muffler imho. It doesnt drone like crazy and long trips arn't a problem
@jackstandnation2 ай бұрын
This system isn't super loud but still has good tone driving it. It's way less obnoxious then before and it makes driving the car a lot better. Thwy have some kits that sound better but I got the car with the exhaust on it and just wanted to change it up a bit
@angelmorfin35974 ай бұрын
Hey brother, do you know if 33 inch tires will fit with a 2 inch lift kit?
@codycartertv5 ай бұрын
That does looks pretty cool! Looks factory almost
@jackstandnation2 ай бұрын
Thanks man! I thought it turned out pretty decent
@desertadventures42215 ай бұрын
Looks nice.. nice video
@curryreeves13695 ай бұрын
shoulda replaced them rusty springs hahah great video tho
@jackstandnation5 ай бұрын
haha it was for a family member so they just gave us the lift and we installed it
@curryreeves13695 ай бұрын
@@jackstandnation yeah just being a troll lol but seriously inspired me to do mine since it’s kinda straight to the point
@jackstandnation5 ай бұрын
@@curryreeves1369 Oh awesome man! Im glad this video helped someone lol
@sweetiepienumber15 ай бұрын
"Hi, I wanted to ask if raising the height of your vehicle by 2 inches has affected its handling on the freeway, especially when taking turns. I think the difference might not be significant, but the last time I raised the height of my vehicle decades ago, it also had larger tires which made the ride louder, like on a dirt bike. So, I'm looking for a compromise between the height and the noise. Also, did you notice any changes in mileage after raising the height? Your instructions make it look plausible for someone like me to do it myself. Thank you, and take care!"
@jackstandnation5 ай бұрын
It still drives pretty well with the lift due to it being such a small lift. Mileage is about the same to my knowledge. We installed the lift for a family member so I haven't really driven it since.
@cloubert013 ай бұрын
Did it increase ground clearance? Was this a quadratec?
@alaskatactical44575 ай бұрын
what size spacers? and was there any rubbing before you lifted it ?
@jackstandnation5 ай бұрын
I don't remember the size of the spacers. It was for a family member so I didn't drive it much beforehand to know of any rubbing.
@marshallsifelani99696 ай бұрын
Am struggling to take the crankshaft pulley off
@jeremywalker24606 ай бұрын
That's going to be so much fun to drive
@jackstandnation2 ай бұрын
Yeah my buddy loves it. That was on low boost ao it really scoots when it's turned up
@brcron0076 ай бұрын
Great Video thanks for making and posting it.
@timlandsberg9406 ай бұрын
Those on factory wheels still?
@user-gg9bj7wt6j6 ай бұрын
cats?
@thek1dd267 ай бұрын
What tire size do you have
@DariusM-hj3yq7 ай бұрын
Do you still have this vehicle and how long you had this car
@jackstandnation2 ай бұрын
It was just a rental but it was a good car the 2 days I had it lol
@SCTTanielu8 ай бұрын
I was thinking about paring these wi to the roughy country 4in long arm to make around 6 in in lift because 3000$ is to much for Clayton’s 6 in lift , if I do this is there anything I should know
@rahulyasseen3528 ай бұрын
What size wheel spacer are u running on wj
@franw519 ай бұрын
How was the day to day drive ability
@user-cv1so8bd4u9 ай бұрын
On rough country site it says the kit won't fit my 2004 wj 4x4 . Do you know why?
@angelmorfin35974 ай бұрын
Bro me too smh the website says it doesn’t have the kit for my jeep either
@Jeepfeenz9 ай бұрын
Worst thing you can do is lift springs and lift pucks, in order to do a correct lift is to do extended links and arms and just lift coils then use those shovk absorbers
@jackstandnation8 ай бұрын
It was for a family member and he ordered the kit. Actually rides really nice.
@benbirch23938 ай бұрын
My 03 WJ with Old Man EMU springs and dampers (not long arm), rides beautifully on and off road, and I've never been hung up or had issues going where I need to go. Okay I won't be doing crazy rock crawling but that suits me
@CHEAPROLLIN9 ай бұрын
Nice valve cover
@jackstandnation8 ай бұрын
Thanks!
@CHEAPROLLIN9 ай бұрын
Great video
@melissahuff848310 ай бұрын
How bad would it be if u didn't realize someone put 2.0 cams in your 2.4 and u turned it on 3 times after timing to 2.4 marks? I thought they just used 2.0 sprokets and read theyre enterchangable. Started it idles rough but sound good if I gas it. I couldn't see the 2.0 marks before I took them off and scrubbed there was soo much gunk in there. Long story. So I just thought they're a tooth off. Now I don't know if it was flipped over or not. 🤦 mom trying to do this for my teenage daughter. I know enough to f some shit up apparently.
@jackstandnation8 ай бұрын
Make sure both holes in the cams are up. If one gear is flipped 180 off when installing them there 2.0 cams.
@wdh11310 ай бұрын
GREAT CLOSE UP WHEN OFF THE CAR...I STILL HAVE TROUBLE WITH GETTING IT OVER THE TENSIONER...THANKS FOR THE VIDEO!
@ivansizhuk395010 ай бұрын
What is a tire size?
@gronvall336410 ай бұрын
Nice, do you have a link to this kit?
@joaquinortega277311 ай бұрын
Buen comentario.
@user-fh1ii4mq4p Жыл бұрын
please tell me the size of the width, they look great
@Fish_Weapon79 Жыл бұрын
What size tire without rubbing
@user-hj4gj5rm3v Жыл бұрын
tell me what brand of wheels are installed on your jeep
@jackstandnation8 ай бұрын
06 Jeep rubicon wheels
@jmilko917 Жыл бұрын
I remember doing my xjs. Wow those very rear bolts on the leaf springs were such a bitch to get off. Used a breaker bar the entire time backing them off. Couldn’t get an impact on em. Smh
@initialb5009 Жыл бұрын
does the castor angle need any adjustment , how does it drive, i see these getting death wobble when lifted 4 inch but this 2 inch lift looks pretty good .
@gotmylk Жыл бұрын
I ran the 228R (228/228/112) for a few years in my mn6 C5. Good little cam especially when paired with ported heads. At the time it had BBK shorties and 4.10 gear. Car made 391/379 at the wheels on A&A Corvettes dyno.
@jackstandnation2 ай бұрын
Those are good numbers. I never had mine dynoed but im guessing like 380whp
@gotmylk2 ай бұрын
My numbers above included WCCH stage 2 ported #241 heads. Which on the flow bench outperformed my untouched #243 heads Substantially. #243’s are only good for about 15 to 20whp in stock form over stock #241. My WCCH heads were a 35rwhp gain over stock. So if you’re 241 heads are stock and you just did the cam (without longtubes) my estimate is you likely saw about a 35hp gain at the wheels over stock. So I’m figuring your car is more like 340 to 345 at the wheels. The cam won’t shine without heads and vice versa the heads won’t shine without a bigger cam. Once you do both the difference in power grows considerably. Then add LTs to the mix and your car is up in the 418 to 430whp range. Then throw on an ECS Novi 1500 and you’ll see over 600whp/500rwtq on a 93 octane tune.
@eliinthewolverinestate6729 Жыл бұрын
Use the factory shock cross pins on the front shocks. My wj didn't make it out of the drive before breaking. 265/75/16 load range E tires rubbed in reverse on incline, but not going forward.
@minamusiklistor93192 ай бұрын
245 wide is the biggest you can go without spacers, I belive.
@unknownstudd69 Жыл бұрын
What is the LSA of your cam 112 or 114, also is your transmission A4 or M6?
@jackstandnation Жыл бұрын
I'll have to check the cam card but I think 112. It's a manual 6spd car.
@ryanlucascarrasco Жыл бұрын
I thinking of doing 112 or even more chomp with 110
@SVfighter12 ай бұрын
114 would be better for a forced induction application, I thinks so not sure.
@p.nathanial8314 Жыл бұрын
"PromoSM" 🤭
@bdc_ky Жыл бұрын
Just got this kit installed on my 02 and it has been great
Пікірлер
NOT recommended to lift the Limited with the Quadra-Drive 4x4 system!
This Jeep looks sweet!!! When you show the Jeep at the end is this with stock tire size? I really like the look of it with that wheel and tire set up! Thanks for sharing!
Why is the right most CAM 180 degrees off? The "UP" is pointing down
Great video, thanks for posting! I just purchased the same Rough Country 2" Lift Kit for my '04 Grand Cherokee. Can you please confirm that the rubber rear lower coil spring insulator is not required when installing this Rough Country Lift Kit?
31”?
awesome
What size wheel spacers are you using
Why not put a new rubber springisolaror on the rear springs? Now it's metal on metal!
did you have problems with stock springs falling out or bowing out after the kit installation?
Does this increase ground clearance? And can it be used in a quadratec?
Rough Country website says No on the Quadra -Trac
According to Alldata the exhaust cam, the one in the back, is supposed be a half tooth below the front one. Yours looked to be the opposite, I’m wondering if that was accidental or intentional? You should’ve covered finding TDC for the #1 piston, just showing you spin the crank to line up the mark could cause someone to need to redo all that work.
These kits are a waste of time and money....first of all if you put this kit on a older jeep your not getting a 2 inch lift cause the stock springs are shot so you need new ones. Save up some cash and buy a 4 inch lift kit that way it's a whole new suspension at the height that looks badass 🤘
I put 2.5 spacers on my 04 and honestly if ur not hitting trails to hard and just want some height then spacers are a good alternative
Estoy haciendo los mismo en mi wj que amortiguadores colocaron ? Muchas gracias
Doesn’t sound aggressive
prolly has gay catalytic converters
Ok, talk to me here. How close to stock quite is it getting? I need my car (B6 A4 Avant 1.8t) to be reasonable sounding for my sanity, but I don't want complete sad stock exhaust. I got the car with a 3 in turbo back and same bullet style junk.... stupid loud. Would you say this is "closer to stock" but obviously still makes some noise? Also, it seems quite at idle, but decent at full song, can you confirm that? Thx
I had this exact same setup on a mk5 gti (2.0t) and ended up installing a 16” resonator in mid pipe to keep the drone down at highway speed. The gti is a much shorter car than a B6 so Id recommend you look into a slightly longer resonator to bring the decibels down but still have a sporty sound when accelerating. Resonator is a much cheaper option and easier to install in a straight section.
What resonator did you add? I had a vibrant UQ on my mk5 rabbit. It did pretty good, just curious what worked for you.
The car has 2 other small glasspacks in it (no cats). They just act as resonators. It sounds a lot better with the new muffler imho. It doesnt drone like crazy and long trips arn't a problem
This system isn't super loud but still has good tone driving it. It's way less obnoxious then before and it makes driving the car a lot better. Thwy have some kits that sound better but I got the car with the exhaust on it and just wanted to change it up a bit
Hey brother, do you know if 33 inch tires will fit with a 2 inch lift kit?
That does looks pretty cool! Looks factory almost
Thanks man! I thought it turned out pretty decent
Looks nice.. nice video
shoulda replaced them rusty springs hahah great video tho
haha it was for a family member so they just gave us the lift and we installed it
@@jackstandnation yeah just being a troll lol but seriously inspired me to do mine since it’s kinda straight to the point
@@curryreeves1369 Oh awesome man! Im glad this video helped someone lol
"Hi, I wanted to ask if raising the height of your vehicle by 2 inches has affected its handling on the freeway, especially when taking turns. I think the difference might not be significant, but the last time I raised the height of my vehicle decades ago, it also had larger tires which made the ride louder, like on a dirt bike. So, I'm looking for a compromise between the height and the noise. Also, did you notice any changes in mileage after raising the height? Your instructions make it look plausible for someone like me to do it myself. Thank you, and take care!"
It still drives pretty well with the lift due to it being such a small lift. Mileage is about the same to my knowledge. We installed the lift for a family member so I haven't really driven it since.
Did it increase ground clearance? Was this a quadratec?
what size spacers? and was there any rubbing before you lifted it ?
I don't remember the size of the spacers. It was for a family member so I didn't drive it much beforehand to know of any rubbing.
Am struggling to take the crankshaft pulley off
That's going to be so much fun to drive
Yeah my buddy loves it. That was on low boost ao it really scoots when it's turned up
Great Video thanks for making and posting it.
Those on factory wheels still?
cats?
What tire size do you have
Do you still have this vehicle and how long you had this car
It was just a rental but it was a good car the 2 days I had it lol
I was thinking about paring these wi to the roughy country 4in long arm to make around 6 in in lift because 3000$ is to much for Clayton’s 6 in lift , if I do this is there anything I should know
What size wheel spacer are u running on wj
How was the day to day drive ability
On rough country site it says the kit won't fit my 2004 wj 4x4 . Do you know why?
Bro me too smh the website says it doesn’t have the kit for my jeep either
Worst thing you can do is lift springs and lift pucks, in order to do a correct lift is to do extended links and arms and just lift coils then use those shovk absorbers
It was for a family member and he ordered the kit. Actually rides really nice.
My 03 WJ with Old Man EMU springs and dampers (not long arm), rides beautifully on and off road, and I've never been hung up or had issues going where I need to go. Okay I won't be doing crazy rock crawling but that suits me
Nice valve cover
Thanks!
Great video
How bad would it be if u didn't realize someone put 2.0 cams in your 2.4 and u turned it on 3 times after timing to 2.4 marks? I thought they just used 2.0 sprokets and read theyre enterchangable. Started it idles rough but sound good if I gas it. I couldn't see the 2.0 marks before I took them off and scrubbed there was soo much gunk in there. Long story. So I just thought they're a tooth off. Now I don't know if it was flipped over or not. 🤦 mom trying to do this for my teenage daughter. I know enough to f some shit up apparently.
Make sure both holes in the cams are up. If one gear is flipped 180 off when installing them there 2.0 cams.
GREAT CLOSE UP WHEN OFF THE CAR...I STILL HAVE TROUBLE WITH GETTING IT OVER THE TENSIONER...THANKS FOR THE VIDEO!
What is a tire size?
Nice, do you have a link to this kit?
Buen comentario.
please tell me the size of the width, they look great
What size tire without rubbing
tell me what brand of wheels are installed on your jeep
06 Jeep rubicon wheels
I remember doing my xjs. Wow those very rear bolts on the leaf springs were such a bitch to get off. Used a breaker bar the entire time backing them off. Couldn’t get an impact on em. Smh
does the castor angle need any adjustment , how does it drive, i see these getting death wobble when lifted 4 inch but this 2 inch lift looks pretty good .
I ran the 228R (228/228/112) for a few years in my mn6 C5. Good little cam especially when paired with ported heads. At the time it had BBK shorties and 4.10 gear. Car made 391/379 at the wheels on A&A Corvettes dyno.
Those are good numbers. I never had mine dynoed but im guessing like 380whp
My numbers above included WCCH stage 2 ported #241 heads. Which on the flow bench outperformed my untouched #243 heads Substantially. #243’s are only good for about 15 to 20whp in stock form over stock #241. My WCCH heads were a 35rwhp gain over stock. So if you’re 241 heads are stock and you just did the cam (without longtubes) my estimate is you likely saw about a 35hp gain at the wheels over stock. So I’m figuring your car is more like 340 to 345 at the wheels. The cam won’t shine without heads and vice versa the heads won’t shine without a bigger cam. Once you do both the difference in power grows considerably. Then add LTs to the mix and your car is up in the 418 to 430whp range. Then throw on an ECS Novi 1500 and you’ll see over 600whp/500rwtq on a 93 octane tune.
Use the factory shock cross pins on the front shocks. My wj didn't make it out of the drive before breaking. 265/75/16 load range E tires rubbed in reverse on incline, but not going forward.
245 wide is the biggest you can go without spacers, I belive.
What is the LSA of your cam 112 or 114, also is your transmission A4 or M6?
I'll have to check the cam card but I think 112. It's a manual 6spd car.
I thinking of doing 112 or even more chomp with 110
114 would be better for a forced induction application, I thinks so not sure.
"PromoSM" 🤭
Just got this kit installed on my 02 and it has been great
Ññ lo Ññ
How big are the tires your using bro?
How much for the 2 “ lift kit??