Good job

@MotoGarageTV

2 күн бұрын

Thanks

Thank you for the very clear video! 👍 I have the same waterpump on my Fjr 1300 but i have 2 bearings.... The one you pressed in and 1 inner bearing.....

@MotoGarageTV

8 ай бұрын

I'm glad it helped. Good luck on your project. 👍

thanks man excellent video

@MotoGarageTV

8 ай бұрын

Glad you liked it! Thanks

great video very informative and easy to follow. I have an R6 and am rebuilding my water pump but I don't know how to remove the old bearing. In the manual it says to tap from the inside but for the love of it won't budge. Can you please help me.👍

@MotoGarageTV

10 ай бұрын

Hello. I'll let you know what worked for me. To remove the bearing, you'll need to first remove the C-clip retainer that holds it in place, then work from the opposite side (propeller side), and remove the mechanical seal. Afterward, you should be able to tap or press the bearing out now that you have access. Let me know if you need any more help. Thanks

Will this work for the 06-07 raven as well ? It’s typically the same right ?

@MotoGarageTV

7 ай бұрын

Basically identical.

I'm rebuilding essentially the same water pump for an fz6 and there's a lot of resistance when trying to turn the impeller after I assembled everything. Is that normal or have I messed something up? It seems to be from the friction of the white seal on the impeller touching the top of the mechanical seal.

@MotoGarageTV

6 ай бұрын

There shouldn't be a lot of resistance. Have you changed the bearings? Have you checked the shaft for damage? warping/ bent?

@richcarthief4778

6 ай бұрын

@@MotoGarageTV I changed the bearing and it turns fine and the impeller is brand new. I’m thinking it could be that black seal is maybe not put in completely straight or something

Hi, nice video. Just a question, just rebuilt mine but I saw in the shop manual that the oil seal is supposed to be installed against the bearing what I first didi jut then the bearing hat resistance due to the contact with the seal, so I installed it like you did, but what is the correct way to install it?

@MotoGarageTV

2 ай бұрын

Hey, sorry for getting back to you so late. I would say go with the manual to be safe. However, the seal should not make contact with the bearing. You will run the risk of the seal prematurely wearing out and allowing oil to pass through. Go with what works. I have been running without issues ever since the upload of this video.

@stevebirkenkampf1632

2 ай бұрын

Hi, no problem thanks for the answer. I had my two first trackdays last week and yesterday and after both I noticed an oil leak at the weep hole. I did it like you in the video because juste like you said when I put it in like the manual says it makes contact with the bearing and you can really feel it how it's making it difficult to rotate. I hope it's just some oil residue from the installation otherwise I can go for a whole rebuild since the oil seal is hard to get out without removing the other parts sitting arround

@MotoGarageTV

2 ай бұрын

@stevebirkenkampf1632 hopefully it's not leaking, and it's just build-up like you said. If it is leaking, double check that the seal was installed in the correct direction and that it's not compromised. Check and make sure the shaft is not bent. Let me know how it goes.

@stevebirkenkampf1632

2 ай бұрын

@@MotoGarageTV will be riding 2 more trackdays this weekend I'll let you know. And yes I checked, everything is installed like it should be. During the rebuild I even put a very thin coat of TB1215 on the oil seal (on the outside of course, not on the inside where the shaft goes) and it's seated very well, can't even push it out of position with a screw driver so that should be good. And shaft is new, I polished the old one to remove as much rust and dirt as I could but since it already had picking corrosion I said okey let's just put a new shaft aswell so I won't have to worry about the old shaft damaging the new seal

@MotoGarageTV

2 ай бұрын

@stevebirkenkampf1632 Sounds like you covered all the bases on that install. I'm leaning towards leftover residue, but keep a close eye on it. Good Luck

Do you have a link to the blue pliers used ?

@MotoGarageTV

5 ай бұрын

Sort, just seeing this now. I'll get them and post for you. I believe it was from Amazon or auto zone

What was your total on all the parts an OEM pump assembly is like 170 free shipping. Trying to make a move thanks.

@MotoGarageTV

8 ай бұрын

Around 75 dollars

@davedorsette

8 ай бұрын

@@MotoGarageTV thanks for the quick reply much appreciated

What’s the best way to pull out the bearing ?

@MotoGarageTV

7 ай бұрын

I pressed it out from the opposite side, and it worked great. The mechanical seal is the same way. After I removed the bearing, I came in from that side to push out the mechanical seal.

@thefinerthingsinlife5963

3 ай бұрын

Sweat it in and out

Mine still leak after rebuild..what actually happening?

@MotoGarageTV

2 ай бұрын

Hard to say, I'm not sure what you did to help you out with your issue. Can you explain a little more?

@alex_sid

Ай бұрын

потому что керамическую втулку нельзя забивать глубоко. Это делается заподлицо(в один уровень) с ротором крыльчатки

Дайте каталожные номера пожалуйста 🙏

@MotoGarageTV

3 ай бұрын

I can help with that. Which parts were you interested in?

@bogdanov3536

3 ай бұрын

Все,что нужно)спасибо