Thanks a lot my friend, finally works i my goggles v2 :)

@Mangorille

Жыл бұрын

Awesome, happy flying!

Thank you! Worked perfectly!!!

@Mangorille

Жыл бұрын

Great! Happy flying!

Спасибо! Отличное решение проблемы.

@Mangorille

Жыл бұрын

Welcome, happy flying!

Great video. I have not had the issue but if I do I will know what to do. Thank You!

@Mangorille

Жыл бұрын

Thanks. Happy flying!

Great Video.

thank u so much I had .606 version with wtfos. After that I upgraded o3 side to 1.07 and saw that DYI side just auto upgraded to .607 and broke me wtfos. After that I just entered your cli commands and reinstalled wtfos. And now it’s working! 🎉

@Mangorille

10 ай бұрын

Awesome! Happy flying!

@Thereivaj_FPV

8 ай бұрын

Puedes cambiar fácilmente a o3 ... No me aparece la opción en en menú..solo Dji FPV y avata

@Mangorille

8 ай бұрын

@@Thereivaj_FPV Did you upgrade the firmware when in both the Avata mode and in the DJI FPV mode?

@jessefpv4949

3 ай бұрын

New to dji.. using v2 goggles.. what mode exactly it " dyi "

@dailydronejourney

2 ай бұрын

@@jessefpv4949 I think DYI is mean DJI Digital System..

fantastic man!!!!!

@Mangorille

10 ай бұрын

Thanks! Happy flying buddy!

Thank you for your work. I don't have the O3 yet but I'm already on 1.07. I'll keep this video in mind.

@Mangorille

Жыл бұрын

Welcome. Happy flying!

Nice!!! Thanks

@Mangorille

Жыл бұрын

No problem, happy flying!

Thank you were much! I had this issue and was about to believe that the v2 goggles doesn't support hdosd at all even with the o3

@Mangorille

Жыл бұрын

Welcome. Happy Flying!

so this version is suitable with avata to right ?

thank you so much! I still try to figure out if I should stick to my goggles v2 or if i keep my goggles 2. How is your plan as of right now? I am not sure because of fitment. And also insecure about range. Is the goggles 2 range with the old vistas and Airunits (using LHCP ANTENNAS) worse then with the v2 goggles because goggles 2 is using linear antennas stock? There is no really reliabale info out there and not even tests betwenn all the setups and antennas

@Mangorille

Жыл бұрын

I’ve had both for about 6 months now, let’s say I finally decided that I’ll be selling the v2. I use the goggles 2 with both the o3 and vista. The vista doesn’t work 100 percent with all the features but good enough. I haven’t noticed any signal differences in my kind of flying (usually within 500m and around buildings and trees). I like the portability of the goggles 2, the displays, built in diopters, and the fact that it can embed the osd elements on the video.

Is there a newer step-by-step instruction video on how to take V-2 goggles that are normally used with Vistas, and update everything for 03 the air unit? Some older videos didn't have the newest firmware back then. And newer videos assume the user has already jumped through some of the hoops. Please reply with link.

@Mangorille

Жыл бұрын

Joshua Bardwell had a video a while ago. The steps are fairly straight forward. You just need to update the goggles in the Digital FPV System mode and then in the O3 Air Unit mode. I think it's this one: kzread.info/dash/bejne/gal-yrmgftHWnNI.html

Hey man, everything works fine as i follow ur tutorial but is there any chance we do not need to bind 03 everytime we change to DJI Fpv Mode/ Caddx vista?

@Mangorille

Жыл бұрын

No, it's been a bug in the firmware for a while now. When you switch modes, the bindings are lost on the O3 side. There's a feature on WTFOS that makes it so that the Vista bindings are retained but nothing can be done on the O3 side until DJI decides to fix this.

Hi, thank you for that video. So does this mean that after these steps I can switch between O3 mode and DIY mode at any time in Googles v2? And will all settings on both partitions be preserved, so they will not be affected and everything will work, including HD OSD in both modes as it should?

@Mangorille

Жыл бұрын

Not sure if I understand correctly. You were always able to switch between the DIY and O3 modes in the V2 goggles. You lose the bindings to the air units each time you switch though and have to rebind. With the new package from WTFOS, you don't lose the bindings on the DIY side but you still do on the O3 side.

@MomoBrut

Жыл бұрын

@@Mangorille Well, expressing myself clearly in three sentences is not easy. So it's great that the bindings and DIY will remain, I have a lot more of those. So after switching to O3 mode you always have to rebind, not ideal but I can live with that. The O3 mode update will probably mess everything up again and it will have to be done again, I mean re-uploading WTFOS, packages and all settings...

@Mangorille

Жыл бұрын

@@MomoBrut Correct after switching to the O3 side, you will need to rebind the O3 every single time. Make sure you carry that small screwdriver / pin with you. If you keep your CLI commands handy, you can do the whole remove/reinstall of the WTFOS in ~15 minutes.

@MomoBrut

Жыл бұрын

@@Mangorille If I remember correctly, it took more than 15 minutes, but that's okay. I have one more question this quad wit Vista? How did you get that 250 mW into the OSD? This is a power of what? VTX? Or?

@Mangorille

Жыл бұрын

@@MomoBrut With practice probably can bring that down. I had all my CLI commands in various video descriptions and was able to just copy-paste them over. The 250mw is the ELRS control link power.

Good morning, I just ran this guide and thank you very much as you partially solved my problem (but I think yes of all .......). I have Goggles v2 (with the same firmware as the video) and going from Avata to the Caddx video units of my self-built ones the bind remains on all drones (and here we have solved a big problem but not entirely ....) but if I then return to pilot Avata I have to bind again (here is the problem I have left but with the lesser evil)........ is there a possibility to keep the bind also on Avata? Thanks Gerard

@Mangorille

Жыл бұрын

No, the loss of binding when you switch to anything O3 requires a firmware fix from DJI. Nothing we can do ourselves and DJI has not fixed yet. The WTFOS only touches the Digital FPV System (DIY) side.

@gherardofaltracco1721

Жыл бұрын

@@Mangorille Thanks for the reply, we trust dji to fix this but I doubt they will fix it

@Mangorille

Жыл бұрын

@@gherardofaltracco1721 Probably their way of forcing everyone to convert all their drones to the O3.

@mangorille I'm interested in that colored HD OSD stuff you showed in this video. I cannot find a video about it in your list of stuff, unless I missed it? can you link it? thanks for your time.

@Mangorille

9 ай бұрын

Hey. Here is the how-to video. kzread.info/dash/bejne/c2eB1qOsqZqdqs4.html

Thank you a lot for this. It probably won’t fix my issue with battery voltage not showing.. not even in the dji Osd. I connected the wires correctly to my flightcontroller and even switching them out doesn’t make a difference. I am running betaflight 4.4.2 on my geprc cinelog 25. Connected the white wire from my o3 to uart1 tx and the grey wire to the uart1 Rex on my fc. Msp is active. The betaflight canvas does not show and the dji voltage shows 0.00. Before all of this everything worked with my vista and wtfo. I am sure it will be figured out but it is extremely hard and complicated.. Kind regards, Dennis

@Mangorille

Жыл бұрын

The voltage not showing is either a wiring issue, a ports setup issue, a software issue, or a physical issue with the O3. Go through each of these and see if any resolve your issue. I had this happen once on a brand new O3 and it took a software refresh to resolve it. I hope it's not a hardware issue, which can happen if the UART wires shorted on the O3.

@sprokkel30

Жыл бұрын

@@Mangorille i refreshed the software and no luck. i then took another quad and hooked it up. in that quad i did get betaflight osd including voltage but not the voltage of dji osd. I then went back to the cinelog who has two uarts and i tried the other uart. nothing no osd at all nor working voltage. i am so sick of this that i will try and send it back... what a mess it is.

@Mangorille

Жыл бұрын

@@sprokkel30 That is very strange, if you get the voltage on the betaflight OSD, you should get the voltage on the DJI OSD as well as both come through the same connection.

@sprokkel30

Жыл бұрын

@@Mangorille yes indeed and this works only on my f7 board with beteflight osd but not on my geprc f411 there I can’t even get the betaflight osd working. Maybe the o3 is faulty we will see :)

@Drone.cordoba

6 ай бұрын

resolviste el problema? @@sprokkel30

Hey! Do the custom fonts work on the dji o3 ?

@Mangorille

8 ай бұрын

Hey. No, the only thing that works right now on the O3 is native MSP and HD OSD.

HI, i'm currently switching to the 03 unit is betaflight OSD supported natively for the v2 goggles? i've never installed the WTOF hack do i need to instal the hack before i switch over? i recently purchased a FC with a barometer and would find knowing my rough altitude to be useful with all the new laws coming in to place thanks for making these videos.

@Mangorille

Жыл бұрын

The O3 supports native MSP canvas mode. The WTFOS hack actually does not touch the O3 side of the software so it doesn't make any difference if you have it or not. If you want instructions on how to setup the MSP canvas mode, check out this video and make sure to read the pinned comment: kzread.info/dash/bejne/fX2d1ZahcsLKpbQ.html

Hello, having the v2 goggles with wtfos and the o3 air unit, can you continue using the old air unit with wtfos without problems? Thanks for you video!

@Mangorille

Жыл бұрын

Yes you can. Make sure you follow this video so that you don't lose the HD OSD option on the O3 side.

@estudioaguilamagnetica3174

Жыл бұрын

@@Mangorille ok thanks !

hi Bro! thanks a lot for the tuto! What happens to me is that when I activate the HD with O3, I lose some OSD legends, like GPS coordinates, speed, etc. But if I deactivate HD, I can see them. Any idea?

@Mangorille

Жыл бұрын

I don't use GPS so can't check on mine but are you sure that they're not just going off the canvas? What happens when you put them right in the middle?

My question is unrelated to this but I am seeing people with INAV and 03 air unit working. I haven't been able to do this. do you have any suggestions?

@Mangorille

Жыл бұрын

I don't use INAV, will wait for others to respond.

for the first time im ussing the wtfos I need to pay to connect the DJI goggles v2 and do the rest?

@Mangorille

Жыл бұрын

Pay? No everything is free. What step are you being asked to make a payment for?

@dronebirdun

Жыл бұрын

@@Mangorille my goggles v2 are not conected to wftos, juts says this, Failed detecting ADB, please (re-)root your device! I'm on mac

@Mangorille

Жыл бұрын

@@dronebirdun Can't speak to a Mac. Do you have a friend with a windows PC that you can try?

hello just started fpv i successfully rooted goggle v2 but i exit by error the "root mode" by cliking on go to dji fpv ui how can i go back? and by the way can i use wtfos with dji fpv?

@Mangorille

6 ай бұрын

Hey. Not sure what you mean. I'd suggest going to the WTFOS discord and posting some more details there for better assistance.

Hey I wanna use my V2 with the 03 rooted it but I haven't updated to the latest to support the 03 unit. Would I lose my root if I update ?

@Mangorille

Жыл бұрын

No, the root is a one time thing but you do need to make sure you follow the steps in this video otherwise you'll lose the HD OSD option on the O3 side.

Hello I'm having trouble too everything is right and to the right firmware. No health check on wtfos using 03 unit. And I only see the basic stuff no beta osd.😅

@Mangorille

3 ай бұрын

Wtfos doesn’t apply to the o3. You’d want to follow the instructions to activate canvas mode (msp display). kzread.info/dash/bejne/fX2d1ZahcsLKpbQ.htmlsi=_CFaAqyMzICWkQy-

@jessefpv4949

3 ай бұрын

The wtfos is for the older vistas.. correct.. but the osd on the v2 I just can't get.. I also just now like right now updated the v2 and the unit 03... using 4.4.. in the release notes.. just plugged a battery in and just the basics osd.. idk I'm so confused

@Mangorille

3 ай бұрын

@@jessefpv4949 If you have the v2 and the o3, you need to follow the instructions to turn on Canvas mode. You can either follow the video I sent or look at the O3 air unit manual. Note that the instructions changed for 4.4. I have a pinned comment in the video I linked on what you need to do differently.

Thanks for this tutorial. I get no luck, unfortunately. I am stuck with "error 5-100-4" when attempting to update to v01.07.0000 at both Consumer Drone Series and DJI FPV Series. ☹

@Mangorille

Жыл бұрын

Are you using a Mac? Seems that like error has to do with a Mac. I found this video: kzread.info/dash/bejne/q5WB2dugoKi3mJc.html

@phiveone

11 ай бұрын

I ran into this error on PC as well. I do not have a Mac but I did upgrade to v01.07.0000 using the DJI Fly App without issue.

Does this update allow the goggles V2 to record the O3 OSD?

@Mangorille

Жыл бұрын

No, the V2 does not have enough horse power to overlay the osd on the video. This can only be done with the goggles 2 or goggles integra. Also, wtfos only works with the old generation air unit.

Who you record the osd?

@Mangorille

Жыл бұрын

You need a Goggles 2 or Goggles Integra. I used a Goggles 2 (there's a little note on the screen saying that it was captured using a Goggles 2).

Thanks for the video. Unfortunately not working for me. Tried 3 times following your instructions step-by-step. Fresh V01.07.0000 HD OSD works perfectly for O3 air unit, but each time right after installing WTFOS, the HD canvas display mode gone. Don't know if WFTOS changed something or something I messed up.

@Mangorille

Жыл бұрын

Sounds like you're either missing a step or doing something in the wrong sequence. Did you run the CLI commands before clicking Attempt Fix in WTFOS?

@xiaobingyi5413

Жыл бұрын

@@Mangorille thanks sir. Yes, I did run the cli commands before attempt fix. Before install wtfos, I checked the HD cavas mode and it worked. But it disappear right after install WFTOS. Tried 3 times, no luck.

@Mangorille

Жыл бұрын

@@xiaobingyi5413 What version are you running on the Digital FPV system side of your goggles V2?

@xiaobingyi5413

Жыл бұрын

@@Mangorille version 606. I have a bunch of vistas.

@Mangorille

Жыл бұрын

@@xiaobingyi5413 That version looks good. Try reaching out in their discord. Looks like this fix does not work for you for some reason.

I don´t get it. My V2 is recognized but I can´t root, it just won´t do it. When I click on root, a window appears showing me the recognized Goggles, but once I click on connect, nothing happens. When I unplug the USB-C cable and plug it back in the steps are actually starting immediately, but after a few seconds it tells me that it failed after 10 retries. I can´t even get it rooted it seems. Running the V01.07.0000 firmware... Any idea? What is the FPV DIY mode? I only see the O3, FPV, Digital FPV System and Avata mode... No DIY mode.

@Mangorille

Жыл бұрын

Are you trying to use your V2 with an O3 or a Vista?

Does it still work with the old AIR UNITS

@Mangorille

Жыл бұрын

The native Betaflight 4.4 HD OSD is only supported on the O3 side of the V2 so you will need the O3 air unit for this to work. You can continue using your old air unit with the DIY/WTFOS side and use the WTFOS to get HD OSD.

@2011Formosa

Жыл бұрын

@@Mangorille Hi, After apply the above procedure, how can I enable the FCC mode and 1200mW with the old air units and vistas. Thanks in advance for your help.

@Mangorille

Жыл бұрын

@@2011Formosa No different than how you did it previously. Easiest is to just install that package on WTFOS. Otherwise you'd be using the naco textfile.

Can I install WTFOS in DJI GOGGLES V2 with Firmware V01.07.0000 even though I never had WTFOS installed using this procedure? I need the most OSD recording in glasses.

@Mangorille

Жыл бұрын

What version do you have on the Digital FPV System side? You'd want 01.00.0606. I have a video on how to downgrade the firmware: kzread.info/dash/bejne/c2eB1qOsqZqdqs4.html

@JurajCs

Жыл бұрын

@@Mangorille My DJI GOGGGLES V2 goggles have firmware v01.07.0000.

@Mangorille

Жыл бұрын

@@JurajCs That's the firmware on the O3 side. What's the firmware on the Digital FPV System side?

@JurajCs

Жыл бұрын

On the O3 page is firmware V01.02.0000.

Failed detecting ADB? what should I do?

@Mangorille

23 күн бұрын

Are you sure your goggles were successfully rooted? Do you have anything else open in the background that could be trying to access the goggles (such as the dji app or even the wtf webpage)?

@zach3738

4 күн бұрын

Same here. I re-rooted, all good the 2nd time.

What is DYI mode? I can see only FPV mode - is this the same?

@Mangorille

Жыл бұрын

DJI FPV is the DJI FPV drone. If you go to the O3 mode, you'd want to select DJI Digital FPV System from Settings > About > Switch Aircraft Model

@pawelturon

Жыл бұрын

I cannot get osd dvr recording to working with my o3 and goggles v2. Is it because I have betafligth 4.3? This instructions is about OSD HD, and would be happy to have osd recorded at all...