Your a legend man. Now at least I have my remote controller 2 inputs registering. I can`t tell you how long I have been scouring the internet for this. Thanks

@TheDroneGeek

2 ай бұрын

You bet! I struggled the same way I’m sure you have been. I couldn’t do it alone, but that’s what is so great about the community - there’s always somebody willing and able to help! Good luck, happy flying!

@Seemless600

11 күн бұрын

@@TheDroneGeek AGREED OMFG THAT YOU SO MUCH ITS BEEN AT LEAST 5 HOURS THANK THANK THANK YOU SOOO MUCH

Earned a sub on this one saved me from losing it and throwing this FPV 2 controler across the room . 😂

@TheDroneGeek

Ай бұрын

I’m happy to hear you still have an in-tact controller. 😂

Simply, THANKS

Good setup video.

@TheDroneGeek

2 ай бұрын

Thanks for the comment. I put a lot of work into it and didn't expect it to get a lot of attention because it's a rather specific problem, but the fact you took the time to say something kind about it makes that work worth it. I appreciate it and you!

Thanks, Well Done!!!

@TheDroneGeek

2 ай бұрын

You're welcome and thank you!

VERY INTERESTING VIDEOS.., It looks as if you do not need to get into betaflight to mess around for synch. the DJI controller... And by the way... I heard the DJI Controller is not working with the PAVO 20 POCKET It looks like the POCKET version has sensors pointing down in order to create estability... I am buying the pavo 20 but I( am thinking about buying also the POCKET one bevause I normally use it for interiors. am I right bout the POCKET version? Well.... I wrote that at the beg. of your video, so I see I have to get into betaflight... But still my question about the POCKET is there... Could you help?

Hello there im kinda new in this but, i had dji avata before and i bought a PAVO20 as u guess, so now i did the 90% of the work i binded all the devices and applied betafly settings. I watched lot of videos but didnt get the right answer yet. So the problem is when i try to arm the drone its closing and opening again. Its resetting itself. While it happening HD icon's bar is rising down slowly and right after that its closing. I gived 10 hours to make it work and i believe i deserved a little bit help. Even from now i thank you for your helpful messages.

You're an absolute lifesaver! I am facing one last issue though. Once the drone is armed, the throttle goes to 100% and i cannot bring it down unless i disarm it. I tried to do the same in BetaFlight motor test (without props) but for some reason the motors are going full throttle after arming. Any ideas?

@TheDroneGeek

Ай бұрын

None unfortunately. Maybe check your throttle settings in the receiver menu? My other suggestion would be to check out your modes tab to see if you have an AUX input that is incorrect. That may be a good one to take to Reddit. I’m sorry I’m not of more help.

Great video! do you know if these settings will work with the iflight defender 20 with a dji 03 air unit?

@TheDroneGeek

Ай бұрын

That's a great question -- I can't verify whether or not it works with the Defender 20 or not -- I had somebody ask a similar question about a GEPRC drone -- it might, but I cannot say for sure. I'm sorry I couldn't be more helpful!

OH man, thanks to you and reditt guy, why does the official website get the uart port wront and dont give you all this information. Can I recommend they use your video officially?

@TheDroneGeek

18 күн бұрын

You can! I'm not sure they will -- but I do have a great relationship with them, so maybe! :)

Hi! Will the CLI (last part) work on the new Firmware 4.5 for the Pavo Pico and the setup with the DJI RC 2?

@TheDroneGeek

22 күн бұрын

It should. I have not heard any issues. I can check with my contact at BETAFPV and follow-up on this thread if they give me a response!

Good afternoon ! First of all, thank you very much for the tutorial, I have seen it about 10 times and I have carried it out step by step, and it still does not assemble the engines. What can be ? I have the turkey 20 with the DJI Goggles 2 and DJI FPV Controller 2

@TheDroneGeek

14 күн бұрын

Genuinely asking...is "Turkey 20" a typo? Because if it is, do you mean you have the Pavo 20...and if it isn't, then where the hell can I get a drone called the "Turkey 20," because I absolutely will be getting one...

@sebastianlobos

13 күн бұрын

​@@TheDroneGeek The Turks are tough.. hehehe, it's pavo 20, translation error was

Question: Will I still be able to easily connect my controller and goggles to my DJI Avata also if I want to use that instead, or does this limit me to only using my Pavo drone going forward?

@TheDroneGeek

Ай бұрын

Yes. The DJI Goggles 2 and FPV Controller 2 do not require rebinding when swapping between devices. All you have to do is select the correct device from that device menu where we selected the O3 Air Unit. Once the goggles are looking for the correct device, they will pair with devices they already know from the initial binding.

@hankis22

Ай бұрын

Awesome, last question. Does the O3 air unit adhere to the same software flight restrictions that the Avata and other drones are subject to? Aka no fly zone restrictions

my pavo flips out, after doing everything correctly following the video....loved THE VIDEO, but do you know why it would? thank you SO MUCH BROTHER!!!!!!!

@TheDroneGeek

5 күн бұрын

Check your motor direction in Betaflight. Toggle on and off (and test with each setting respectively) the "motor order reversed" toggle. If that does not solve the issue, restore it back to the position it is in during my video tutorial and try turning "low power mode" on in your goggles. I recently had an issue where my Pavo Pico was being told it was rolling to the right when I was giving no stick input, which made takeoff impossible because it would just flip over when I gave it any throttle. That said, if it still doesn't work, try going to this website and reflashing the firmware via the CLI to factory defaults. Then try the process over again: support.betafpv.com/hc/article_attachments/21131998083865

@TheDroneGeek

5 күн бұрын

Btw...I'm going to ask just for the sake of covering all my bases...did you check your propeller installation? It should be configured for "props-in."

It is still not working for me Im using nazgul ECO with rc2 and the revire tab in betaflight is still not working. Do you have any idea how to fix this?

@TheDroneGeek

11 күн бұрын

This tutorial only applies to the BETAFPV series of prebuilt drones with the O3 Air Unit. I cannot advise you on a different build. I'm sorry!

@LucasLens444

11 күн бұрын

@@TheDroneGeek oh okay I have a pre built drone but yes not the right series. Thank you anyway

Is paring back to a official DJI drone simple u just change the device on googles and put remote 2 in paring mode to connect to DJI FPV

@TheDroneGeek

Ай бұрын

Actually, I think with the Goggles 2 you just have to pair once and then the goggles pick up and connect to the devices they remember. I’ve never had to re-pair with a drone using the Goggles 2 that I can recall. You should be able to bounce in and out of different drones - same goes for the controller 2.

@ebolarium

Ай бұрын

Thank you for the great explanation. Just one simple question; Can I record video without Googles. There is a sd card slot on O3. Can I use video record button on Dji Rc2 to recording? Thank you..

will these same steps work with the geprc mark5

@TheDroneGeek

2 ай бұрын

Not confirmed. You could try it and if it doesn’t work you could just re-flash the drone’s original firmware and start from square one. I imagine it might work because the GEPRC drones are formatted similarly to the BETAFPV drones.

#betafpv #pavopicodjibind #pavopico #betafpvbinddji #dronefix