probablemente tu motor de ventana no este dañado solo este atascado, suele suceder por muchas variantes, la solución es solo desmontarlo y fuera del carril de la ventana y hacerlo funcionar por unos segundos y luego reinstalar y volverá a funcionar, suele suceder que cerrar la puerta fuerte la ventana vibra y descoloca los dientes de engranaje, haciendo ese sonido de "clik" atascando el nivelador del engranaje.

Do you have video for the door handle? My rear door handle got broken. I ordered a replacement and took the torx bit out to loosen it to get it out but now the new handle is loose against the door... and I tightened the torx screw back but anybody can pull it off

Great video

@JustFixinGarage

10 ай бұрын

Glad it was helpful thanks for the comment

What if both rear windows don't work?

Awesome video. Thanks

@JustFixinGarage

11 ай бұрын

My pleasure! hope it was helpful.

my ram promaster 2500 driver window button clicks but doesn't roll down. i took out the control panel and cleaned the circuit board but still doesn't work. can i assume it's a motor or regulator?

@JustFixinGarage

Жыл бұрын

I’d only make that assumption if your seeing power and ground to the motor . Sometimes a switch goes bad and sends power but no ground . Please note the it reverses polarity to go up and down . You can technically get power and no ground and vice versa and it not work . The issue would be switch related not motor . You have good odds it’s the motor but if you have a volt meter you can test power and ground at the plug on the motor while engaging the switch

@1969MARKETING

Жыл бұрын

@@JustFixinGarage ok i'll try that. thanks.

Wow that’s the same kit I have of scrapers and stuff lol

@JustFixinGarage

Жыл бұрын

Must have been an Amazon suggested kit . Best 15 (I think ) bucks I’ve spent

Bruh perfect

@JustFixinGarage

Жыл бұрын

Thanks for the comment!

Hi my motor for my challenger will roll my window up only then when I install a new one it rolls only down. Please help me. Thx

@JustFixinGarage

Жыл бұрын

I suggest you use a test light and see if power is being sent to each terminal on the motor when you are trying to roll up or down. It could be a bad switch not making proper contact to ground it etc. Before I replaced my motor I confirmed I was getting power past the switch. The switches are known to go bad due to dirty contacts/terminals .

@martinadudley534

Жыл бұрын

@@JustFixinGarage thank you. I've change the switch 2 times as well and I've have had a few people check it out. I will try that then I'll just send it to get repaired through the dealer. They want 150 just to diagnose it but im getting feed up. Again thank you!

@JustFixinGarage

Жыл бұрын

@@martinadudley534 very strange that a new motor goes opposite of the old one. Dealers will charge 150 and say it’s the motor without looking at it. Hopefully it can be figured out . I would also try sending voltage to the motor to see if it will go up and down that way just to rule out the motor . That can be done with jumper wires from the battery

where did you get the new window motor from ?

@JustFixinGarage

2 жыл бұрын

I ordered it on eBay it was the cheapest option . I suggest you confirm which part number you need from mopar and search eBay and Amazon and google for the best price.

Thank you for the video.

@JustFixinGarage

2 жыл бұрын

Hope it was helpful .

This is dumb, in order to see if the new motor is applicable you can look at hp, rpm, voltage and amperage. Don’t just check and see if it looks like it

@JustFixinGarage

Жыл бұрын

Send me a link to a video of you doing it and explaining so everyone can learn something from you .

@AustinJones330

Жыл бұрын

@@JustFixinGarage sure I can do that, I have air handlers to work on tomorrow I’ll send a vid

@AustinJones330

Жыл бұрын

@@JustFixinGarage is there a name plate on those motors

@JustFixinGarage

Жыл бұрын

@@AustinJones330 these were factory replacements the only logo or brand was just the mopar brand . I’m sure they outsource to another company but I’m not sure what it actually Is