Fiber cement board (Hardie) siding on my old townhouse saved me and my dog from a fire. And probably saved the entire building from burning down. The back deck (all wood) and the patio under it were on fire raging out of control for about 20 minutes from start to fire hoses on it. This raging fire was right up against the Hardie Panel fiber cement board siding and it never burned through. The foam insulation and plywood sheathing behind it were untouched. It blew out the windows eventually of course, just as the fire trucks were coming down the road. That fiber cement was literally life saving.

@thecarpentergarden2943

3 жыл бұрын

Do u have picture ?

@thecarpentergarden2943

2 жыл бұрын

?

@Elricky124

3 ай бұрын

Which fiber cement brand did you use?

You should do a part 2, with brick, stucco, metal, etc.

@chuckhursch5374

3 жыл бұрын

Yes, definitely stucco. My neighbor changed from wood lap siding (like we have, ugh), and his house looks nice! 👍🏻

@deanabossio3091

2 жыл бұрын

I agree! Brick is still best. You have to repaint fiber cement every 5-7 yrs.

@sidingmaster

2 жыл бұрын

Or just use this instead of that junk kzread.info/dash/bejne/dGuL0a19dN2yc8o.html

@charlesrodriguez7984

2 жыл бұрын

@@deanabossio3091 well fiber cement takes 9 years before you see any fading if multiple paint coats are added.

@joemike509

2 жыл бұрын

Also would have been nice to know the temperature on the backside of them

Forget about buying a lamborginni to flex. Matt 😌 is burning OSB just to flex

@triggeredtroll6466

3 жыл бұрын

🤣🤣

in 2002 I resided my house with James Hardie siding. it wasn't prepainted but I gave it 2 coats of Sherwinn Williams A1 paint. I sold the house 6 years ago but I drove past it this week. It's still got the original paint and looks great. I built my current home 6 years ago in the Black HIlls National Forest. This is a semi arid area and fire is a concern. My house is a Deltec and it came sided with ALLURA. My personal experience is that it doesn't compare to Hardie. I sided the 1000 SF garage as well as other portions of the house. The Allura was extremely fragile. I could only carry it on edge and just getting it to that position was delicate. I broke several pieces. I also found that it was not uniform in thickness. At times I measured with a caliper and found that it was inconsistent by about an 1/8 of an inch. It also was inconsistent in width of the planks. they varied by about an 1/8" as well. By my experience, I wouldn't recommend it. With Hardie I could snap lines for the top of the planks. That was not possible with ALLURA.

@willbass2869

3 жыл бұрын

To echo Apsco above....Thanks!

@jfruser

3 жыл бұрын

Now THAT ^^^ comment is worth its weight in lumber. Or gold. Same-same these days.

@thedudeaaronfyi

5 ай бұрын

that sounds like triple the labor to me! thanks for heads up.

@IE-cz9qq

4 ай бұрын

i recently got an offer to side my house im switerland with james hardie, i got a good feelimg about this product

Thank you for this. My husband are looking to have our siding redone and this is super helpful. Last week it got to 116+ so… this give a lot of food for thought

Real life situation. My home burned in 2008. James Hardie siding. I stood and watched flames come out a basement window and up the side of the house. No fire damage. Made me such a believer that I have had it on every house since.

@thecarpentergarden2943

3 жыл бұрын

Do u have photos

@thedudeaaronfyi

5 ай бұрын

did the siding become brittle afterwards? im just really curios. like can a house survive a brush fire and just need some fresh paint afterwards? or would it need replacing afterwards? im sure there's allot of variables but im really curios if your siding was compromised or if it really is that incredible. thanks for your comment.

Matt's vinyl laugh..inhaling the plastic fumes

@warronfrench8163

3 жыл бұрын

Makes me think of Burt Reynold's laugh.

@Randomname183

3 жыл бұрын

It was cringeworthy

I just watched the most recent _This Old House_ episode on their KZread channel and was very disappointed that they were showing people installing an engineered-wood siding in Paradise, CA (where a wildfire had destroyed almost the entire town). The siding had a 1-hr fire rating, but in my mind, it should have been some other material (e.g. fiber cement, metal, stucco). I was also expecting to see some people rebuild with block walls, brick facades, etc. (materials that are inherently more resilient to fire) since wildfire is not a problem that only happens once. If you live on an urban/wilderness boundary, it's potentially a problem all the time. They rebuilt the town, which is "noble" or "brave" or whatever, but it seemed like they didn't learn from their mistakes, which makes them seem kind of dumb IMO.

@MrJramirex

3 жыл бұрын

They are also building some houses with vented crawlspaces and vented attics. Yes they showed a fire retardant vent mesh but I bet the majority are not going to use that product and go code minimum which is a 1/16th mesh. That helps slightly not enough. Why have ventilated anything when it's not necessary and it's a major fire risk.

@safffff1000

3 жыл бұрын

Californians don't learn, after many fires, very few are doing the proper fire prevention.

@cengeb

3 жыл бұрын

@@safffff1000 Hardie fiber siding and tile roofs, walls should be all block and concrete too

@fredochs

3 жыл бұрын

That's what I was thinking too when watching that TOH episode...

@pablo4youtube

3 жыл бұрын

What they need to do is pass laws to only allow building exteriors with metal panels, concrete/stone, and cement fiberboard and require a 10-20 ft vegetation buffer with nothing but gravel or decomposed granite between that buffer and the house’s outer walls. Otherwise, people will skimp to save money and will build houses that burn. Confederacy of Dunces.

I have seen vinyl siding melt from sun reflecting off a window onto the siding.

@plowboy5220

2 жыл бұрын

That's ridiculous... or you saw it the only time that ever happened.

@Richard_Storm

2 жыл бұрын

@@plowboy5220 Tis common - here is a video from "Ask This Old House" dealing with the very issue. kzread.info/dash/bejne/oa2d1ZOtkqXecrw.html

@thedudeaaronfyi

5 ай бұрын

@@plowboy5220 this is extremely common. the fun part is tearing half the building apart to repair this. then you realize that the color is totally different between the old and new cause a couple years in the sun is rough on plastic. its the worst option by far.

@daniellem1838

3 ай бұрын

This has happened to my home. It’s from the neighbor’s window. We are all vinyl siding, 5ft apart, lowE windows in this community.

Love the video Matt. I would love to see a torture test with zip and a house wrap(fluid applied, self sticking one, etc) to see how each perform.

2:07 That laugh 😂

Fiber cement has become the defacto siding option for us, we build in Boulder and high Rockies of CO as well as BigSky-Gallatin Gateway, MT, all due to fire risk and insurance. We are seeing more and more steel siding the last 5 years. It’s class A fire rated, none of the silica issues and many more aesthetic options than fiber cement. We’re building home now in Nederland, CO that will be our first steel siding, along w/stone. It was a choice of architect and client but I am looking forward to seeing how well it installs. It’s about 20% higher price than JH siding in material costs

@charlesrodriguez7984

2 жыл бұрын

Even in Colorado Springs the majority of houses have hardie fiber cement siding. It looks good, keeps fire out, and it doesn’t rot or melt.

I live in the Midwest. Temps vary from-20 to +95. I worked for a chain of gas stations in doing maintenance. Many of the locations had builder installed fiber cement siding. The problem we had was that the product would shrink during cold weather and crack the siding at each nail location. I put LP Smart siding on my house 5 years ago and it looks like new( my house is 50 years old) I don't know what brand of cement siding was used of if it makes a difference but in my area, I would recommend engineered siding

The vinyl siding by my patio has a visible droop in a section where I unwittingly fired up my propane grill too close to it. Won't do that again, and as soon as I can afford it I'm going to get the house re-sided in fiber cement or Boral or something like that.

I'm watching a commercial .... within a commercial .... within a commercial

@praetorianblade6490

3 жыл бұрын

Inception- Build show episode.

Australian here, never heard of vinyl cladding before, sounds like a straight up recipe for disaster. Though we've got other alternatives that are equally as cheap & nasty

@ericspda

3 жыл бұрын

In mild climates it’s VERY common and works perfectly fine. Last a long time, it’s cheap, easy to put up, and easy to repair. It’s not super durable if you hit it with a lawnmower or weedwacker, but it usually looks fine for decades.

@jimmypchacko

2 жыл бұрын

Lots of houses built or remodeled in the 70's and 80s have it. Was sold as a wonder material requiring no maintenance. Vinyl was installed over my natural cedar shingles, I just think they look tacky.

@joshharper1906

2 жыл бұрын

the house my grandparents built 20 years ago has it on it, no issues. It doesn't dent and its cheap. If outdoor fires is a concern then you would want to consider something else. If a fire breaks out inside your home, it doesn't matter what is on the outside of your house. We don't have forest fire issues or other concerns here so vinyl has been great in general.

As a volunteer fire fighter,. I have seen vinyl melt on houses all the time. I have seen full two story sides of houses melt away.

Could be interesting to add aluminum siding to your fire test.

Great demonstration! When I added a work shop on to the back of my garage, I settled on Allura for the siding. I could get it in widths that matched the clapboards on the rest of my house. It wasn't cheap, but worth every penny. Found some aluminum corners that also matched the house (I wish Allura would carry these in all sizes. They were hard to find.). It's only downsides are it's heavy and it needs to be carried vertically or it will likely crack or break. But the look is amazing, and I do like the fire safety issue as we do barbecue right next to the shop..

@benzun9600

2 жыл бұрын

How is allura holding up? Looking to install it

@MyLilMule

2 жыл бұрын

@@benzun9600 Excellent. ZERO issues.

2:00 Matt's laugh is awesome

Fiber cement siding is common for fire-rated separation walls here in New Zealand. Cedar cladding is really beautiful if the budget allows for now and future maintenance, which is the top pick for cladding an architectural-designed house in Wellington. NZ.

It would be interesting to see metal siding also in this test.

@Wub892

2 жыл бұрын

wouldn't do anything other than char or change color. Screws holding it up may transfer heat to a wood back and maybe start a fire, but id imagine that would take some time. something else is bound to catch fire before that.

@sidingmaster

2 жыл бұрын

kzread.info/dash/bejne/dGuL0a19dN2yc8o.html

so the sponsor for the video is the winner - never saw that coming

@michaelrdegroat

2 жыл бұрын

I trust Matt, but do wish he'd gone unsponsored or an unrelated sponsor for this video. I believe the results would be the same, but it would feel...cleaner.

I always enjoy and respect your work, Matt

Right now, depending on how you did it, a log cabin might cost more than a stone castle of the same size. wood siding is fancy, weird times

I live in Northern California. Icf, Metal roof, and cement siding is the way to go. With fire insurance being what it is that's a no brainer.

@willbass2869

3 жыл бұрын

Never been up there. What % of houses built with block/brick? Thx

@jwristen24

3 жыл бұрын

@@willbass2869 not many but I'm seeing more and more. Fire insurance is skyrocketing. Only way to stave it off is to try to get a 4hr rating

@willbass2869

3 жыл бұрын

@@jwristen24 makes sense not much brick/block. Y'all are so close to major timber supplies in NorCal/PNW that prices were cheap.

@jwristen24

3 жыл бұрын

@@willbass2869 we are close, in the the forests but they don't give you a cost break lol.

@MrJramirex

3 жыл бұрын

@@willbass2869 less than 1% I would say. A lot of stucco, which is really good but most have vents so still a high fire risk.

What do you think of Everlast Siding? I completely agree with your assessment of standard vinyl siding, but I have seen some very nice Everlast siding installs.

@jerryphipps9863

2 жыл бұрын

We chose Everlast over Hardie. No regrets. Outstanding product. Of course my opinion but it looks as nice as Hardie and install is much easier. Matt time for you to do a review of Everlast. Unbiased please. Not a pitch of a product or the sponsors product.

Yahoo! Now check out Perfect Block, I’d love to see you do a video on the pluses and negatives of it.

In Europe, brick semi detached houses can be completely gutted by fire on one side of the party wall and the other will have only minor damage at the join. Exterior walls definitely want to be fire proof 🔥

Also love Hardie siding,. Never have used Alura.

That laugh when the vinyl went up😂😂😂😂

We have used fiber cement siding exclusively for over 10 years due to ability to withstand fire as well as hurricanes. Being on the coast in SC, we have the chance of land falling hurricanes, ie Hugo, Floyd and other named storms. Wind resistant., as well as fire due to close proximity to other home. Brick is second choice that we use depending on customer. Great video and will save to show potential new build customers on their new construction. Stay safe and see you on next video.

@gceurve1

3 жыл бұрын

Check out Everlast. Lighter, no painting ever, no caulking, tight butt joints, 140 mph wind, labor and material warranty. Beacon can supply in Charleston

Very fun video Matt! I do wish you picked on a higher quality polymer like the Injection Molded Polypropylene products like CertainTeed's "Cedar Impressions Perfections" or Stylecrest's "CedarCove 8' Roughsawn" ... I've used both. Unlike poly-vinyl which is most often paper thin extruded product, Injection molded Polypropylene is very thick and looks great and has no seems like Hardie Plank siding in my community. I appreciate how they lock into place for superior wind protection on the coastline. Truthfully I am much more concerned about wind loading. How about a wind load test. It doesn't need to be an ASTM certified test. Cheers, Eric

Thinking about our rain screen assemblies- would that nice stack effect suddenly become an issue? I can see the OSB lighting from radiant heat and making a rocket engine behind any siding… thoughts?

What a pyro, your enjoying this a little too much. Love your vids Brother Man. Keep em coming.

I’d love to know the cost of the real rebuild.

@tonynguyen1815

3 жыл бұрын

Sponsored cost? Or real cost?

@face2faceyouth

3 жыл бұрын

@@tonynguyen1815 real

@mikemessenger1681

3 жыл бұрын

He said a while back real cost would be around $400/sf

@face2faceyouth

3 жыл бұрын

@@mikemessenger1681 I didn’t remember that, but okay. That’s a lot.

@jasonawilliams

3 жыл бұрын

$400 psf if you and I did this, but he’s probably at less than $100 if you consider all his sponsors.

Fibre cement siding is pretty good cladding material. But please remember that there are also fibre cement panels in various thicknesses and sizes, coloured as well, that can be used on your house or building. Eternit makes excellent fibre cement panels. So does Nichiha. And they don't look like "siding".

Good to see all this . Thanks!

Another expense factor not mentioned is insurance. It is my understanding the insurance companies consider cement fiber a masonry siding, same a brick or stone, so could reduce your annual homeowners insurance premiums since it is more fire and hail damage resistant than other siding. Year over year that could add up. Talk to your insurance agent about that and shop around.

I’m curious how thermally modified wood siding stack up to fibre cement siding.

With rockwool insulation behind the fibre cement boards you would have a good set up. So long as your doors and windows hold out.

You are correct with respect to vinyl being used heavily in many areas of the country. In the Cleveland, Ohio suburbs it is the most common siding. Beside initial cost, the main attraction is ALMOST NO MAINTENANCE, no painting, no resealing, no anything. The house we are in has 30 to 40 year old vinyl siding. After 10+ years of us living here, we had some mold growing on the north side of the house and detached garage. We also had some dirt build up on a couple of areas covered by overhang. It cost us a few hundred dollars to have those areas professionally power washed. Amortized over 10 years, that is like $30 per year. Actually, when I was talking cost, I should point out that the majority of houses in our area were originally built with wood siding and at some point some insulation was added and the vinyl covered the wood siding. It was about 1.5 to 2.0 times as expensive as painting. In the time the vinyl has been on the house, it would have had to be painted 4 to 6 times. That vinyl siding has paid for itself many times over.

Could you do a fire test with panels set up as rain screens?

If a house is on fire the house next door with vinyl starts to melt.

@christophergruenwald5054

3 жыл бұрын

The radiant heat will catch adjacent structures on fire if no cooling by the fire department.

@nedalabokasem4067

3 жыл бұрын

When a house on fire the fire coming from inside to outside ! So the last layer of the house is siding ! The fire resistant should be in the interior face of the wall before fire catch the insulation!!!!

@thecarpentergarden2943

3 жыл бұрын

And insurance re sides the house and the house doesn't burn down even with vinyl

@rock3072

2 жыл бұрын

Been to many fires that start on the back deck, run up a wall covered in vinyl siding, and straight to the attic, eventually burning down the roof.

@thecarpentergarden2943

2 жыл бұрын

@@rock3072 how did the fire start on a back deck ?

As a DIY I really like the LP smart siding. I was able to reside my whole house myself and didn’t have to worry about the dust. Much less weight moving around 16ft pieces. Very durable and looks great. Matt I followed your advice installing a rain screen. In Ohio fire isn’t a concern.

@timgleason2527

3 жыл бұрын

Anything you’d have changed? Thinking of doing the same in PA.

@eagleknight2701

3 жыл бұрын

@@timgleason2527 Tip is use H molding on butt joints. I think it looks better. Cans of primer spray paint also makes it easier to seal edges or cuts then trying to brush those. The Gecko gauges are a must for DIY.

@timgleason2527

3 жыл бұрын

@@eagleknight2701 thanks!

@leisureavidgentleman8901

3 жыл бұрын

@@timgleason2527 good Question, so I’m following.

@sparks6666

3 жыл бұрын

I just did a big solo diy siding project with LP Smartside. I just caulked the joints and they pretty much disappear. Love the durability, ease of cutting and 16ft lengths.

Broke my heart to see you burn hundreds and hundreds of dollars worth of wood for your demonstration. Hands down I'm using Hardie Lap Siding and this demonstration just confirmed it. Thanks Matt.

Hey Matt, Thank you for the demonstration. I have recently purchased a house near Grass Valley CA and it's in a wildfire area so I need to use fire-resistant materials whenever possible, I'm going to be building a patio/ deck area, fencing and a storage shed. So I have a couple of questions, is T1-11 cement board siding fire-resistant, composite deck, and fence boards fire-resistant. would be a good show building in high fire-risk areas.

My new construction home was built with Hardie Board. This was fun 😁

Would love to see some low cement content Fibre Cement Board make some in roads into the market. Many benefits over natural timber but embodied carbon performance is a negative in comparison

Vinyl is cool!! It's cheap, lite and it's virtually maintenance Free!!! So who cares if it melts with fire?? If there's fire inside your house it doesn't matter what happens to the outside, your house is lost!! And as far as not being recyclable... Nothing in construction is

@YudronWangmo

2 жыл бұрын

Clearly, you don’t live in California. Lots of houses burn from the outside in.

Love your show Matt and watching that vinyl melt like cheddar on a barbecue burger was hilarious. But I have to help out a fellow gringo by asking you not to repeat the “más y memos” (more and less) comment. It’s actually “más O menos” (more OR less). My Colombian wife would slap me if I said “más y menos”. I have learned so much from your vids so up the great work…. Just stay away from the Español mi amigo!

I put viber cement panels on 2 of my homes. I put a piece in my BBQ pit and turned in on for an hour. All it did was char a little. Was still substantial. I could possibly attach it to my house if I wanted.

The engineered wood does have an accelerant in it. Once it catches the glue burns even hotter than the wood. Fought quite a few fires and several houses that caught as exposures. Never had to deal with a Hardie sided house as an exposure.

@cengeb

3 жыл бұрын

that engineered wood siding stuff looks like crap, it's OSB with cement painted on, what a dopey product...hardie cement fiber is the best

Fire resistance is a huge factor here in California.

I would love to see Matt do a review of Alside's Ascend composite siding product. It's being compared to the durability and fire resistance of fiber cement and the easy installation and low maintenance of vinyl siding. Hype or innovation?

you are a damn good presenter of facrs, succinct, unbiased and waste no time. You should do more videos on construction DIY budding builders

I had a “grilling incident” at my old house. Grease drip pan in my gas grill ignited and flared up. HUGE flames pouring out of the grill. Ribs were toast unfortunately. I’m thankful for the hardie siding I had on the house. Melted the paint a little. Had to sand, prime, and repaint.

@buildshow

3 жыл бұрын

That definitely shows the fire resistance of Fiber Cement!

I'm going with Glass-Fiber-Reinforced Cementitious Panels GFRC siding for the cladding is light weight, won't burn, and can look like wood/stone/brick/etc

@Matt What percent of new construction is being done for homes for sale to individuals vs homes for sale to corporations, often for them to rent out? Saw a Second Thought video that asked that question so I figured I'd forward it to someone more in the know. Rent for a 500 square foot studio apartment in between Denver and CO Springs: $980. Zillow monthly estimate for a 2 bed 2 bath house with a garage in the same area: $1,200... with $60,000 down. I'm stuck either living with my mother till I'm 40 to afford a down payment, or just never owning a home and giving all my money to corporate landlords forever. It used to be rent till you can buy, now it's rent till you die. Or put another way "The bank says I can't afford a thousand dollar mortgage, so I pay two thousand in rent."

My vinyl is probably 15 years old, and it is done... color is the same, but its all flimsy and warped... planning on doing fiber cement next

I'm quite impressed with the OSB behind the vinyl :-)

Having a little too much fun here.... 🤣 Great test man! 👍

The Fiber-cement board does look like the product of choice. I don't like dealing with mold, don't want fire from a grill, and don't want to deal with rotting boards either.

Our barn burned as a kid. It melted the vinyl off one side the neighbor's house 100 feet away. Our house was cedar shakes and closer, no damage.

Interesting. Would liked to have seen some actual Shou Sugi Ban, too, though that could be done with a few different types of wood, I guess.

@christianswanson7571

3 жыл бұрын

Well we ended up with some Shou Sugi Ban after all, just had to move the samples a little closer. 🤣

What about sealing paint on houses, love to see a video on this, Fire resistant paint and heat resistant paint. Nice video.

I love the concept of cement siding..i just can't get behind it for home usage. My place has dents in it. Not to mention handling and cutting pain-points. Maybe one day, they would embed some 28 gauge wire or something to toughen it up.

@elslick

3 жыл бұрын

Or a wire mesh.

@Shadi2

3 жыл бұрын

@@elslick @Adrian Sanchez you guys are describing stucco

@elslick

3 жыл бұрын

@@Shadi2 No, we're saying they need to add more reinforcement to cement fiber siding. I know what stucco is and you use a metal lathing, I am saying they need to add a metal very thin mess to the cement fiber siding so it not so flimsy. Putting up long runs you can snap a section easily and it doesn't hold up well to hard impacts.

@FrancisKoczur

3 жыл бұрын

Glass fibers are embedded in it, unless they are using cheaper wood fibers Glass-Fiber-Reinforced Cementitious Panels are probably the best.

@cengeb

3 жыл бұрын

@@elslick That's why hardie trains installers on proper handling and installation, get guys that know what they are doing, not pretend siding guys, guys didn't break one piece installing my hardie stuff here, and they had some complicated cuts, especially working off my back room with 8 Velux sky lites to work aroundguys only do hardie, when people see hardie compared to vinyl, they all choose hardie..

the vynil looked like a ghost screaming lol

Seen plenty of vinyl melted from grills to close.... But I've also seen fiber cement fall apart due to freeze/thaw cycle and disintegrate in 7 years or less, by the way I'm in Central NC

Does fiber cement get brittle or start to break off in small chunks/pieces over time?

As a contractor, I peeled fiber cement, siding off of a house that had completely disintegrated from water even had replaced the OSB

How insightful, Matt. May I specify Allura on your recommendation?

Matt should have done a water test as well. FIRE/HEAT & WATER/“COLD” mainly the only 2 siding issues. The SYSTEM is how we should be looking at this.

It would be very interesting to see the temperatures of the back face of these products.

Fiber Cement SIding " Hardy Board" will deteriorate if exposed to too much moisture. Example is when a two story upper floor and the siding continues above the garage roof. We quit using it in Minnesota for that reason. If you take the LP siding that looks like OSB on the back and soak it in water for weeks it will still look the same. The resins used now days is incredible.

@AlanShirtsink

3 ай бұрын

I live in Hawaii 200 ft from the ocean. Had it on my house for 17 years and still looks new

I installed Certainteed cement/fiber. Missed out on the class action lawsuit so now I just have crappy shrunken/sagging huge gapped siding on my house. Thanks for the info. Looking for a new siding now.

@thecarpentergarden2943

3 жыл бұрын

All fiber board is bad to use and the dust is so bad for u

@cengeb

3 жыл бұрын

@@thecarpentergarden2943 making up nonsense....plastic bottles are dangerous...everywhere...pick siding is cheap...and toxic during mfg. And cutting..and flimsy

@thecarpentergarden2943

3 жыл бұрын

@@cengeb lol as u coment on a post of a person that is having issues with the product. Your a joke

@thecarpentergarden2943

3 жыл бұрын

@@cengeb umm I'm not installing plastic bottles 😳. Yes it bad during manufacturing but way more people install the products then the people with big special masks and protection. But fiber cement is just a bad for the people during the manufacturing.... but plastic isn't bad to cut. Use tinsnipes or a vacuum on a saw. But cutting Hardie is bad with any blade. The chopper cutting tool just destroys the product. The hardie blade just makes a ton of poison dust. Which u need to tell people 25 feet away when u are cutting it. Worksafe bc code. Also need a big very nice mask. but Wait dont smoke, eat or drink with the dust on your clothes either. 🤔 and the product doesn't stand up to snow or water. But yes it can survive fire lol who cares about fire 🔥 😅 I Don't have a bon fire 5 feet from my house ever weekend

@cengeb

3 жыл бұрын

@@thecarpentergarden2943 your a joke? What?

Thank for sharing! But May I gave u little advice? Even if this is just a small fire walking i that fumes, even in small quantities, means you are breathing dioxine! It is incredible poisonous even in minor quantities. Btw ALL the plastic, especially the one used to binding OSB under fire release dioxine! Not to be a technazi, it is really dangerous, I am a professional like you that is why Indare to give you an advice. A small exchange for all you teach and share that is impossible to give it a price. Thank . God bless you

Hey Matt. I have another question. I know if you take care of the seams and the foundation to wall gap if the zip system, it is manages water, air, and vapor very well. What happens when you nail siding or other things to the wall? Doesn’t that deteriorate the properties of the zip system and a failure could happen. Also, how does the zip system manage vapor? I feel like any vapor that gets into a wall cavity if a house built with zip wouldn’t be able to get out because of the low perm rating of the system. Would half inch plywood or thicker with a fluid applied house wrap be a better option? Thanks!

@hopkinshome3799

Жыл бұрын

I use drainwrap behind hardie to get any water out

I’m 2 minutes into the view and the vinyl siding already looks like when you blow a hairdryer on the blinds.

I was looking to see if anyone mentioned the class action lawsuit. Only saw one comment and a few more about cracking. I am an architectural designer and used Certainteed fiber cement on my own home (completed in 2012). Noticed some cracking in the first 18 months and assumed it was simply due to settling. Started recommending my clients not use it on new construction and only on remodels, since settled had already occurred. Fast forward several years and I figured out how it was installed partially incorrectly. Laps not to be caulked (plan for water to get in, give it a way to get out), all cuts painted, 3/8" gap in butt joints, etc. So I thought it was failing simply b/c of improper installation. Wondered if any of it could be repaired, I figured not since it seemed to me the only fix was a full reinstall. Have been thinking on the time when I have to re-do that and planning for some better assemblies underneath it. Fast forward to last year when I discovered there was a class action lawsuit and I was NEVER notified. By anyone. And that the deadline had passed. Now I see where they ran out of funds and the folks who participated seem to have not received their second (remaining 50%) payout and were left holding the bill. Certainteed fiber cement is now Allura. I would REALLY like to see some studies and information on the durability of this product, the issue with the fly ash being used in the manufacturing, and how many people have been left being burned (pun intended) by this situation. It seems I am one of them. As they sponsored this video, I would be surprised to see anything negative posted, but it's a real problem. I love the pros of it, but I think it's rare for it to be installed properly (which will void a warranty), but if it's a faulty product in the first place, they won't take responsibility for it, won't work to improve the product, and won't help the people they've hurt . . .I'm trying to find if there's a better product out there. As I had a nasty hail storm less than a week ago, my siding is even more damaged as it has gotten increasingly more brittle over the years and has too much flex in it where it's pulling loose from warping. I have to deal with my own situation, but I am becoming aware the larger picture is quite tragic for many folks. I might go with something else, but if fiber cement is still my best option, I'll likely go with Hardie AND do a shake, not a lap to reduce the potential for cracking. I would really like to see this addressed.

Your laugh made my day.

@timgleason2527

3 жыл бұрын

I think we all have that laugh when playing with fire.

Would have liked to see a composite siding in this video. Like ASCEND by Alside.

Talk about flaunting wealth. Matt’s out here burning plywood

@blackwaterfarms5893

3 жыл бұрын

These KZread channels are a business, and this test is part of that business. How would you suggest a test of this nature without actually burning something? I for one appreciate the comparison and will help everyone think through the options...

@yaroslav920

3 жыл бұрын

@@blackwaterfarms5893 it was a joke. i know how youtube works and the value these tests bring.

Brick and block baby! Can't beat it

Like the "ASBESTOS", siding salesman, of the 50's ! I remember as a, Child, almost as good as the "Fall-out" salesman, of the 60's.

Hey Matt, I am looking at a product from Duration. It’s a poly-ash product that doesn’t need a gap, 16 ft. Length, and doesn’t absorb water. Just wondering if you have come across this.

Matts new Neighbors "street full of cars, bonfire in the driveway, constant noise...i assumed he wasnt that type of youtube star" matt risinger, Jake and Logan Paul's long lost brother 🤣🤣🤣🤣

Just curious, Did you use Allura on your Real Rebuild or James Hardie? In an earlier vid you talk about installing James Hardie color plus, but at the end of this one you say that “this is Allura on this house that I built”.

@sailorloki

3 жыл бұрын

I’m also wondering the same.

I would like to see you add Efis siding to the comparison.thanks

how does fiber cement compare to stucco with regards to wind and fire?

Nice test! Go ahead

Can fiber cement be installed over old vertical wood siding?

What about steel siding? I feel like its missing in "The Rest" group..

@scha0786

3 жыл бұрын

Cause it would win and he didn’t install it on his house. Steel has been around the longest and will be in the end. Also steel siding has reflective painting in it to decrease heat gain from the sun in the summer.

@TheBroot0999

3 жыл бұрын

Aluminum siding here

What’s best for soundproofing?

A good external option here in australia is a product called Hebel hebel.com.au/segment/houses/ Its basically aerated concrete panels, light weight, fire resistant with good thermal and acoustic properties. Not sure how the R values translate to USA numbers

@apscoradiales

3 жыл бұрын

I thought I read somewhere that it's R1.2 per inch, but don't quote me on it which is not very much. AAC units are excellent building materials, but masonry contractors in North America are totally clueless about them, and how to build with them. They would not know what to do with them. They're common in Europe, though - look up Ytong. AAC work best as far as finishes, and insulation are concerned is if you put EIFS on its exterior.

@marek.lochki

3 жыл бұрын

​@@apscoradiales Not sure on what the panel rating on its own is. For a wall system using hebel, 179mm to 210mm thick, it has an R value of 2.06 to 3.22 in Australian R values which is equal to R11 to R18 in USA R values

I'm just here for the "Build Show Drinking Game" Drink any time Matt says "BOMBER"...

Mr Risinger, would you speak to the pros and cons of replacing OSB sheathing with the older shear bracing method? Current OSB and plywood prices raise these questions. Still, structural compromises are of paramount concern. Thanks.

@jimyeats

3 жыл бұрын

Lol just hit the southwest all you have are a few sheets of osb at strategic locations on the framing and then your foam, wire, and stucco.

@FrancisKoczur

3 жыл бұрын

Let-in bracing is still done, as well as corner only sheathing. You probably want an engineer to sign off on a modification unless it's standard, might negate any saving.

What about WPC siding? Is it as good as FCB siding?

Also interested in how you vent your attic without burning down the place.

@jwristen24

3 жыл бұрын

He did a video on it. Vented top cap with corovent to fill the low's of the raised seam panels.

My house was built in 2007 (I'm the second owner) and has fiber cement on it. I have to assume that whoever installed it maybe didn't do it right because it has cracks galore. LP SmartSide going on in the spring. It might not be the best for fire resistance but at least it won't crack!

@darienredsox1878

3 жыл бұрын

A building inspector once told me that the take a close look at every house that has fiber cement siding because so many installs are done wrong and lead to problems. If installed right it will outlast other sidings.