For those that have a whirlpool washer and couldn't get it into trouble shooting mode do this. Just move the dial to "Normal" then do this in increments of one. I believe this will work no matter what way the dial is pointing but I moved it to "Normal" just because. Left / Right / Right / Right / Left / Right, move the dial and when both "Spin" and "Done" are lit up press start. That will put you in manual test mode. The codes are the same as far as testing. For me "Drain & Spin" was the agitation mode.

@zephyrias

Жыл бұрын

thank you! a single normal left to right got it to unlock! yeah the "drain and spin" was the cause.

@Fit_Ministry

Жыл бұрын

This worked for me

@saltygirl68

8 ай бұрын

Thanks!

@yessieq7760

5 ай бұрын

Nothing happened on mine. Not sure what I'm doing wrong or what's wrong with the machine. When I do turn it on only the locked light turns and then off but no cycle

@FeliciaFerreira-ou1vr

13 күн бұрын

Mine too I'm so frustrated 😮

Ben you are amazing! I am a new first time home buyer and you saved me buying a new washing machine! Thank you!!!

Thank you for another great video Ben. This is the exact washer I have and will help in the future if they're issues 🙂

@bensappliancesandjunk

2 жыл бұрын

Its an incredible mode that maybe 1% of people don't know about. Literally, we can take this washing machine, throw an extension cord on it outside our shop, and just hammer these modes and know the entire life history of the washer in 2 minutes. We can weed out maybe 98% of failures doing this.

@collinlamont3855

10 ай бұрын

Yes that you very much, very helpful information

Great video. Really works 😊

Thanks again for the great content! We have a Kenmore Model 110 26012010 HE Top loader. Every once in a while I need to reset the machine as it fails to complete the spin cycle on it's own (just sits there...). I used your excellent advice and was able to determine a fault code F7 E5 (Shifter Fault) was stored (an OBD port would be nice like on my cars :) ). I followed up with a Drive System-Shifter tests (service manual SPIN and AGITATE Tests) and all the tests worked fine. Everything worked when manually tested. I cleared the diagnostic error codes which I have done in the past. It's laundry day (Saturday) !! I suspect it'll work for a while. Anything else I can test?? Thanks again for putting the time into these videos for us homeowner/DIYers.

@leftylee5068

Жыл бұрын

Run the Calibration Cycle portion of the on board Tests.

I can't believe how easy it is.

Thank you sir.

Thanks for your informative videos, I had recently asked about the lid lock.

How do i get my lid lock to unlock i tried reseting it but its not working

Wow good to knoe thanks.😀

@bensappliancesandjunk

2 жыл бұрын

No problem 👍

Hey thank you so much for this man! Mines was leaving my clothes wet and wasn’t spinning all the way. It wasn’t draining the water from the clothes. I found out that by resetting the washing machine the problem was fixed.

@GrandmasterHobbyist

4 ай бұрын

u mean just doing the left right right right left right fixed it ?

This works on a Kenmore 500 series washing machine the spin around to normal 360° then right three, left click then right one. Works like a charm.

❤😊❤Thank you so much

We just replaced the actuator and cam a few weeks ago . Got caught up on all the laundry. And now it wont agitate or spin. I can hear it trying too but it does move. Is the actuator broken again or do i need to replace that piece under the agitator?

What if washer won't do anything in or out of test mode? Nothing happens at all

Hi ben. i work in hubbard ohio, i got a kenmore washer out of storage and hooked it up and all it does is lite the fill light and lock lid light..but does not attempt to fill. Just does a clicking noise. I replaced the capacitor and the water valve so far. could it be the locking lid functioning as to why it would start/ fill ect. thank you.

I like how I have the Sam washing machine

Hi I have a maytag mat20cs I am trying to find out why when I press the on button nothing happens . Can you please advise me on what to do please . Thank you

My washer stays on lock. Every time I shut it. It doesn't let my washer work. Because it stays locked and can't open. What can I do about that.

@ellieellie856

Жыл бұрын

Same

@Rayallwayz

Жыл бұрын

@@ellieellie856 I had someone check it. What was wrong with mines is that. The part where it locks. There's a piece that locks and unlocks it. Mines was broken. I had to get that piece changed

@ellieellie856

Жыл бұрын

@@Rayallwayz thanks Ron I am looking into purchasing a new lid lock system hope it works

Ben I have this exact washer but the lid lock dont work. Is it easy to fix?

I have this same washer and will try this to reset. My problem is a bit different in that clothes don't seem to be getting rinsed completely. My daughter is doing her laundry and using vinegar in place of softener (less gunk buildup). Problem is that we've noticed there is soap in the water even before adding soap to the wash cycle. Would this reset help anything or is there a filter that may need to be cleaned, etc? I'm disabled and unable to get behind the washer (63 years old). Sorry for the most likely stupid question.

@speaklifegardenhomesteadpe8783

Жыл бұрын

Try to run an empty load with just pool shock in it to clean out the gunk. This might buy you time until someone can check your filters if there is any. Run it a few times this way if it's really bad. ❤😊❤

@collinlamont3855

10 ай бұрын

I've see this in the past and not sure if it's the same in your case but these newer machines and newer HE detergents need very very little detergent to wash your clothes .I suspect the soap you are seeing is left over soap from the previous load ,I know in my case that was the issue ,hope this helps.

@flightmizzarc

8 ай бұрын

No such thing as a stupid question

My kenmore ‎22352 the blue Valve for cold water cracked. The door is locked. I tried to do the test, but it is not doing anything. Right wait half a second right right left right after full rotation counterclockwise. It does nothing. It is stocked in Locked with the lid red. I removed the lock mechanism thinking that would get me out of locked mode, but now I can't close the door and the machine still is locked. Now when the valve cracked Water did go inside the machine. so much so that it was filled with water. the motherboard is basically right next to the valves which is very dumb, but I didn't make the thing. Is it possible that the motherboard was damaged by the water or did the Machine go into a safe mode and lock the door to prevent damage. All I know Is that when I came back from work the machine was filled with water and there was water on the floor. right after that the machine is stocked in locked mode. Since I haven't replaced the part that has been damaged yet it is possible that the machine is waiting for me to activate the cold and hot water to allow me to use the reset mode? or the motherboard was damaged by the water. in other words do this machine has a mechanism that protects its electronics from water? please help. I just bought the thing 1 year ago and I have problems already the Amazon people installed it. My best guess is that when they hooked the hose for the cold water they did something to it and the small crack they left became bigger and bigger overtime until it finally broke. W10683603 Washer Water Valve

do you have part numbers for the major parts for this style of washer, I guess I need the clutch and or shifter , mine is not spinning at all , and just gives up with a click or something lol!

Hi I have a whirlpool washing machine that doesn't want to spin and people that came to have a look tells me its the pc board is there any chance that i can talk to you about this because I really need your help

Hi i have the same model was washing aload of clothes open the lid in the middle of wash and it locked the lid wont open what should i do to get it to open up?

@brycesnyder9158

7 ай бұрын

If you find this out, I would really appreciate the knowledge, I’m in the same position

Do you have a video on error/trouble codes for this machine?

@bensappliancesandjunk

Жыл бұрын

Yes multiple on my channel

After I enter the manual testing mode, I pushed the start button as you did. Your “locked” illuminated, my other 5 lights just continued flashing…

I have a whirlpool cario washer and I believe it's out of balance. The washer sounds like it wants to explode., however it still washes, but it's leaving my clothes wet. Can you please help me out here? I have a disabled person in the home and need to wash every day. Thank you Ms. Dillard

Does this work for a how to reset whirpool top load impeller washer it’s got no agitator and I still can’t get it to work it does go on but none of the touch buttons work only thing that effects the lights or changes anything is spinner one but still won’t cycle or change or let me do anything. I just bought this 700 dollar washer from Home Depot maybe 5-6 months ago

What if the fill light comes back on as soon as I move the dail either way

As soon as i plug mine in the locked light starts blinking then the sensing fill illuminates theb it gooes to rinse

🙏🙏🙏 My whirlpool is very similar to this one bit my issue is,it fails to lock now no light from the lock sensor.

@marydufren3699

11 ай бұрын

I have the same problem. Have you figured out how to fix it?

@sariahlace5944

11 ай бұрын

@marydufren3699 No problems actually was only mistaken,at that time. sorry.

I took out my broken lid lock and then replaced it. The red locked button continues to flash and my machine won't reset. I have tried this at least 10 times correctly and still won't reset. Any suggestions as to what to do next. Thanks for any assistance

@roaneeroane3451

Жыл бұрын

I cant even unlock mines i am having the same issue but it stays lock and wont reset if i figure it out i will let you know

@barbaraday1

Жыл бұрын

I got in diagnostic mode couple hrs ago...due to my lid lock clicking. And after getting in diagnostic mode couple times...about gave up. Then it worked like brand new. But after another load...same lid lock situation. My 3rd load now....after getting back in to diagnostic mode. It's running as should now. I never take the lid lock off....cause I do not have that tool handy. So....my question is. Do I need to replace lid lock? Going in to error codes may send me over the edge.😢

Any way to increase the water level?

hi, great video - any idea how to bypass (jumper) the lid lock circuitry to test if the lid lock is truly the issue I have? In diag mode it fails the first test (lid lock). thanks much

@casperthompson7152

Жыл бұрын

Having the same problem, have you figured it out?

@curtpfister7212

Жыл бұрын

Yeah, get a new switch

@gwood6969

9 ай бұрын

Sorry so late, when you lift up the lid and expose the wiring on back panel, you should see a green wire, a gray/black wire & a white wire. Leave the green wire connected just as is (ground) strip the white and gray wires and twist connect the two wires with a wire nut. Use electrical tape to wrap the new connection you just made to keep it from getting wet or damaged by surrounding components. Shut down the lid and replace all the hardware that was removed back to starting position. The washer should operate as though the lid was locked when in fact it is not locked, it was bypassed. Hope this works for you!

I need this written

I have to open and close my lid to get it full of water. I can't seem to find too much on it researching. Please help!

I surely missed it... but how do you know if a part or cycle is not working and needs attention? After start button is pushed on code, if all the lights blink and nothing happens, does that mean it is a problem?

I wonder how many plants they use to make this machine. Yours has the Made in America label. Mine I bought from Lowes was made in Canada. Not that I think that's a bad thing.

So what do you do if the lock it's self is busted and the stupid machine won't fill even if I push the lock in myself

@so252

Жыл бұрын

Same for me. My washer will only respond in diagnostic mode. The lock lid light is preventing me from using the washer.

@kento53140

Жыл бұрын

No one in the net states what happens if the lock mechanism is damaged.

Ben my washer is stuck in drain mode,no lights,no response,if I spin the basket manually it will stop trying to drain momentary. If unplug and plug back in no lights just a pump that comes back on.

@bensappliancesandjunk

Жыл бұрын

I have a video for them if they run constantly. Check my channel out for it

Hello Ben. I'm really enjoying the depth of explanation in your videos but I have not seen one that addresses the issue I'm having with my Amana (Whirlpool) top loading washer (NTW4700YQ1). When I plug in the washer, the "Fill" light is flashing green and nothing else is responsive. If I press the Start Button, the Fill light goes out ( plus no display lights) and the drain pump activates. the pump does not stop until I unplug the washer. I've replaced the Lid Switch and tried to reset, but no response, just the flashing Fill light. I replace the Actuator (same result). I just replaced the pump thinking there could be an issue with it, but the response was the same, except that the pump sounds stronger and smoother. Could it just be a bad Master Board? I can't seem to clear the flashing Fill light. Thanks, Jess

@bensappliancesandjunk

4 ай бұрын

Likely this video would help: kzread.info/dash/bejne/pGZpl6eIZKewfbw.html

My machine has no agitator so I am beyond annoyed that such a thing was designed into these machines, especially seeing how often they seem to not only frustrate but outright fail the consumer. Arrgh!!!! So my question is, can I remove the lid lock striker as you describe here and just permanently bypass the useless lock feature?

@bensappliancesandjunk

Жыл бұрын

Theoretically yes, as long as the striker is in place and the lid lock system works

@prettyawesomechick

Жыл бұрын

@@bensappliancesandjunk Thank you. Actually, after having watched (and wondered) I went ahead and gave it a try. Troubling to see how exactly this machine operates (very little water, intervals of cold water gets added when hot is selected, forcefully bounces clothing around rather than simply agitating them) but happy to say it works! Thanks again!

What if after testing everything the washer won't start a cycle?

I can't seem to get into the diagnostic mode it's not working and it's the exact same washer

Please Help: I can’t seem to get my washer unlocked. I’ve cycled through the modes and tests on this video but it does not unlock. Am I just doing something wrong still? Thank you so much for any help

@NoahSelf

6 ай бұрын

Did you ever get yours to unlock?? I am having this same problem.

So... how did you get the machine to LOCK the lid while in Manual Test Mode?

@bensappliancesandjunk

3 ай бұрын

I pressed the start/pause button once I set manual mode, it's the first test

@sandracavazos9877

3 ай бұрын

​@@bensappliancesandjunk what if the lid lock works in test mode and recalibration but won't engage during sensing fill mode?

Need help please my Whirlpool washer is shaking wildly and I already change the spring (4) when i did this Manual, when i was on the Spin Mode my washer spon wildly even there no clothes inside need help please

@bensappliancesandjunk

Жыл бұрын

Check to make sure it's level. Also check hub

What if it does nothing, no click, no lights, only thing I can get it to do is run a bit of water for a few seconds, then stop! Any suggestions? I need help!!

@bensappliancesandjunk

Жыл бұрын

Check for error codes. It may be failing out of a test needed to run the unit, like the lid lock, ect.

Can't get to work. Tried many times. All the lights don't come on just the sensor light.

I have a whirlpool WTW4816FW2, washer will begin to spin and agitate if I start it by hand but it won’t do it on its own, anyone have any ideas? I’m at a loss

I followed the diagnostic test. The lid lock does not light up and just keeps clicking. It won't do any other with it. Is there a way to bypass lidlocking? I usually just run washer and never open lid until wash is done anyway...

@bensappliancesandjunk

Жыл бұрын

These lid locks can't be bypassed

@donnaandytakach5837

Жыл бұрын

Thank you

@donnaandytakach5837

Жыл бұрын

We did buy the part comparable for our machine numerous. The lid switch also and the switch does not go into the bezel. Looks to be exactly the same except the lock on the inside won't allow it to go through. Wondering if maybe it is that way until it is installed 🤷‍♀️

@bensappliancesandjunk

Жыл бұрын

@@donnaandytakach5837 did you watch my video on installing the locks with the bezel?

@donnaandytakach5837

Жыл бұрын

I will look for it. Thank you

I am not getting no lights come on SO show me how to program it

I can't get the diagnostics to light up, any other idea?

@sunfloweracres9b327

Жыл бұрын

I don't have an agitator

Mine doesn't seem to agitate

FYI, I put a cotton ball in the locking hole and it finally clicked and the washer started working.

@patdamac8973

Ай бұрын

It wouldn’t lock at first??

My lid lock doesn't activate

I may be modern, but it doesn't clean the clothes very good. I wish for the old ones.

Stuck on the wash don’t know what to do 😢

This unit won't run past the Is rinse cycle reset it twice what is the problem

@xariobeckles6194

2 ай бұрын

I have that problem too

My washer will light up but nothing else.

Machine dells with water and that's it. Wont do anything...no reseting

My, washer ,light is on it don't trun all the lights on

Ok

When I do this my red lid lock lite stays flashing

Washing machine has clothes and water in ready won't do anything drain spin or wash . Help whirlpool washer WTW5300SQ0

He'll yeah thank u Save me In Wife a Hundred busk fie Some obe to cone look at Our washer thanks

I bought a brand new Whirlpool washing machine top load haven't even got to wash a load of clothes in it repairman has been out three times already he has recalibrated everything washer don't work then he checked the the motor was getting hot so he changed that then Calibrated the washing machine washing machine still does not work I have been looking for an email address for the main corporation headquarters cannot find. It's a shame a man pays good hard-earned money and can't even wash a damn load of clothes

How to ruin a good appliance with circuit board b.s.

@BurtGummer85

2 ай бұрын

It was never a good machine.

@slyslaughter5115

2 ай бұрын

@@BurtGummer85 A brand fallen to Bits and pieces

Very poor video, after you get diagnostic mode activated! Very bad choice to go through the steps and not say what each step entails. Made this a royal pain to go over. I had to keep running it back, to write down what was going on. I only hope that when I do my diagnostics I haven't missed an important step that you left out in the no commentary section. Hope you edit this thing and put in commentary.

@bensappliancesandjunk

3 ай бұрын

You're literally the first person to say this. I've made a dozen videos on the diagnostic mode. Please watch multiple of them, because this on ONLY deals with manual part testing, period.

@ufc354811

3 ай бұрын

And you're a douche

I guess this guy doesn’t answer questions

@bensappliancesandjunk

Жыл бұрын

I get about 50 questions per day. I cannot answer all of them. What's your question?

@speaklifegardenhomesteadpe8783

Жыл бұрын

​@@bensappliancesandjunk 😂 ❤ we all feel like your here just for us cuz we luv you❤ 😂🎉 I'll steal his spot since he's been mad seven months now... 😅 My lid lock won't reset. I have lid lock error faults. It won't do anything but add a little water then click the lid lock several times and that's all she wrote. I need to drain and spin what's in there.

Lol yeah right this is bs and doesnt work

@bensappliancesandjunk

Жыл бұрын

Yes it does. I do this every day at my business. What makes you think it doesn't work?

@davidweum

9 ай бұрын

Mine is stuck on finish and I cannot open lid. I've researched it. Any suggestions?