You are the only one here with the most accurate diagnosis of the bouncing issue. Everyone else is throwing parts upselling. Thank you bud

@daviddodge4433

2 жыл бұрын

I had moved my washer. After moving it back it was out if balance. Your video helped fix it. Thanks so much.

@joshcobb4100

2 жыл бұрын

Glad it helped you all!

@rachielbonilla3776

9 ай бұрын

Thank u, now my washer is like a drum, I’ll try to checked it later

This video maybe a couple years old but it was my saving grace. I had literally checked everything and couldn’t figure out why it was still banging around and off balance. I was to the point of breaking down to get a different washer. So thank you very much putting this video up. It was exactly what was wrong with mine.

Thank you for posting this. Never would have thought to look at the plate. I was able to reposition the plate by myself. I had to unclip the back spring and then alternate inserting 3/4" boards under the motor and gear box as I "walked" it upwards. Then I could take my time repositioning the plate.

@joshcobb4100

Жыл бұрын

Great!! Good job!!

This worked on my older model Amana, I can't thank you enough! You saved our wallet and our laundry!

You saved me. Sock got stuck in pump removed the sock put it back together. Took the whole neighborhood to hold it in the house. Found your video. Did like you said. And all the neighborhood went back home. Thsnks

Thanks a heap, man. This was exactly my issue. Replaced the clutch and coupler for a different reason and this must've moved in the process. They never mentioned to check it in any of repair videos I watched. Thanks again!!!

You rock! Old people still work on their sh*t and we thank you!

I'm Appliance Technician Specialists, I gotta say you were 100% correct!

Great video thank u for sharing! I was so frustrated after thinking I fixed it and putting it together just to hear sounds from the basement like a freight train was passing thru!❤

I changed the suspension springs by myself!! The dang washer is still knocking.. decided to search again and now I am stumbling upon your video. Hopefully I can do this by myself and it fixes my washer that sounds like a war going on in my basement during a spin cycle.

@joshcobb4100

Жыл бұрын

Good luck!

@NickiMac

Жыл бұрын

@@joshcobb4100 thanks!! It's fixed and that was the issue! Been working good since. But wish I would have known before doing the rods😔

@bubbagump1306

4 ай бұрын

My situation now. Changed the springs last night, now looking for further answers.

@katietuck1969

3 ай бұрын

My situation as well.. Maytag. Changed the springs worked for 1 day, now I'm going to try this as well

@supjay3945

21 күн бұрын

Well changed springs but havent tested if it was cause of the banging. If it still has issues ill try this solution. Thx

Excellent diagnosis!!! My sears 500 had been Shaking like crazy..all 5 springs good, plate location good, even removed balance ring to make sure fluid was there..I did notice my drum movement was very sticky...pads again , were perfect. I pushed up the drum and sprayed silicone lube on all 6 pad sets...washer runs perfectly..another possible cause..sticky pads

Thank you for thinking about us who love our older top loading machines. You can't replace quality with technology advances when it comes to washing machines. Great job!

Josh I can't thank you enough for posting this video. I had the inner and outer tubs off 4 times. My wife and I prayed about it,, about 30 seconds later she found your video. Your video is spot on. Now our 20 plus year old washer is humming like a champ!

@hardcorecopper4120

3 ай бұрын

Prayer always helps!!❤

@charlottestripland2042

3 ай бұрын

Agree. Prayer works

@joshcobb4100

2 ай бұрын

I’m glad I could help! Good job getting it done! ✅

@kathyhyams5757

2 ай бұрын

Josh me and my 25 year old granddaughter changed the suspension by ourselves it worked it was aggravating as hell but it worked I didn't realize it could've been a number of other things making my tub shake like that though I'm so glad that did it!

@joshcobb4100

2 ай бұрын

@kathyhyams5757 awesome! Good job!!

THANK YOU! I was about to take the machine outside for target practice. Finally, after weeks of trying to find out how to fix and replacing parts, I found your video and it saved my sanity.

@joshcobb4100

3 жыл бұрын

Glad I could help!

@jamiehoover9348

2 жыл бұрын

LMAO.... 🎯 Practice 😆😆💀

Thanks! I think you've been am essential help! Being a former mechanical engineering student and mechanically inclined, not to mention scouring MANY KZread videos to find a solution that didn't seem apparent, I came across your video and this potential cause, which no other video I have seen addressed. After watching your discovery, I rechecked my machine, and I think my issue matches! Going to address it shortly. Appreciate your discovery of this cause. Helped me out tremendously.

I got to thinking after watching this video that should be the first thing to check for the Shake Rattle and Roll problem. Great video 👍

Amazing! Thank you so much. Such an easy fix. I watched so many videos on this issues. You are definitely the only one to show this fix.

Man you saved me for real. I don't have hundreds to pay a repairman. I was able to fix this exact issue and now it works. Thank you once again.

Thank you! I got rid of a machine several years ago that I couldn't get it to stop banging. I replaced the drive coupler in the unit I have now and it started doing the same thing. This fixed it!

Just replaced basket drive assembly and this issue showed up (wasn't the original problem). Other youtube channel said nothing about aligning up the parts when removing/re-installing motor/drive/pump assembly as you explained. THANK YOU!

Much appreciated man! This was my exact problem and you just saved my bacon. Thanks for taking the time to make and post this video

Great video, Thank You. Replaced the shaft bearings and seals on my Kitchen Aid Washer and this plate was mis-aligned after. Could not figure out where it was supposed to go until I saw your video.

Just what I needed....was sure the springs were ok! Thank u for making video for DIYers.

Thank you for posting this video. I changed my clutch and then the machine was going nuts by shaking. Thank you for saving me money and time!

Just encountered this after changing springs,, could not figure out ,,BUT PULLING MY HAIR OUT WHY?.... YOU ARE A GENIUS LIFESAVER! Thank you a million times over for making this video.. CHEERS!

Thanks so much! I had done the clutch repair along with the capacitor due to no spin, I guess all that new force that it didn't used to have now had the strength to break the inner tub shaft where it had been rusting away. After replacing the inner tub it was spinning really bad and couldn't figure it out as the springs looked fine. Saw your video and remembered while I was doing the clutch that plate had some loose and I didn't realize it had to be lined up a certain way. Lifted it up with a piece of wood (was thinking later a scissor jack might work too) and was able to line it up correctly and now it's working great again!

we've replaced all the suspension and counterbalance springs on our 90's Kitchenaid washer and still had the tub leaning front right after a few loads, just sent this to my husband as something for us to check next. Thank you because I refuse to get one of those newer washers that don't wash clothes properly ever again!

Thank you so much! I replaced the bearings and seals after noticing a leak and then the bouncing started! I was replacing the springs and happened upon this video…saved my brain from exploding. Thank you so much again!

@joshcobb4100

2 жыл бұрын

Awesome! Glad it helped!

Thanks brother! I was about to go crazy I changed out the basket drive and then this happened! 💆🏽‍♂️ thanks again ✊🏽

OMG I have been going crazy with my Whirlpool Cabrio doing a dance. First I replaced the bearings, then the rotor sensor, then the springs and now its actually moving all around the kitchen. My son is fed up but I am determined to find out what is wrong. You are a genius!!! I will show him your video and again have him take it apart to see if this is the problem, but I'm sure it is. I always do large blankets but THANK YOU SO MUCH!!!

The old washer in my place had the motor fail and I had just replaced it with a second hand one when the "new" one had this issue during the first load I ran. I had tried replacing the spring in the back, checked all the others, leveled it, was considering either calling out a professional or replacing the balance ring when I finally found this video. This was exactly my issue and while it took some contorting to do it myself (and a fair amount of cursing), it absolutely fixed the problem! Thank you so much!

@joshcobb4100

Жыл бұрын

Awesome!! Good job!

You just saved me from kicking the front of mine in. Mine was so bad it put a hole in the drum. Thank you so much!!

You are a freaking genius. I struggled with this for hours after replacing the clutch. I cracked the plastic tub. After this simple fix the machine runs like new.

@orlandojohnson5742

2 жыл бұрын

Ikr thank God for internet information highway!! So many things to learn & not be so intimated by! We can all fix things if we are paying attention patient & persistent!🙏🏽👌🙌🏽👋🏼

Did this after trying everything else and fixed it in two minutes with my son Much appreciated, brother

@joshcobb4100

2 жыл бұрын

Awesome!!!! Glad I could help!

Thank you for this video . We checked the springs ,and pads all good . Hopefully this is our problem with the washer . Thank you so much for this video

You are the man. Very good analysis. I had moved my washer. After moving it back it went out of balance. Without your video, I would have lost time and money. Thanks a LOT.

@joshcobb4100

2 жыл бұрын

Great!!

On Kenmores/Whirlpools if you take the inner and outer tubs off with the agitator you will find that plate which on mine is triangle shaped has alignment holes. There also happens to be 2 alignment pin containers on the sides of the main platform. Take the pins out and use them to properly orient the triangular shaped tub support back in place and then stow the alignment pins back where they were. These older machines are SO much better than the sensitive newer styles and much more dependable. It's a shame the government stuck their useless nose in to mandate water saving machines that work like garbage.

@joeKisonue

Жыл бұрын

I wonder if those pins are also shipping isolation pins?

@47f0

7 ай бұрын

Has nothing to do with how much water they use, and everything with manufacturing cheaper stuff that looks like the guts of a Mattel toy electric car. The new machines look cute on the outside, but underneath it's a mess of skinny plastic pulleys and skimpy sheet metal.

Thank you so much for sharing this. I was afraid I damaged the transmission/rod last time even though I’ve taken apart several times successfully before. Took me a while to find this video but so glad I did before ordering new parts smh.

Just used this video to fix my washer and impress my wife. Thanks! BTW, the piece on the bottom of my washer was white metal, so a lot easier to spot.

@joshcobb4100

Ай бұрын

Then my job here is done ;)

You have helped me so much I'm a 55 year old disabled woman and I just repaired my washing machine with the aid of your videos and I'd like to thank you for that because it just saved me over $300 It was only a $20 fix so THANK YOU SO MUCH I'll for a question about this jumping around of the wash drum After I repaired the machine I recalibrated it now you have me questioning something shouldn't my recalibration have reset that bracket if it would have been knocked off ( I really don't want to have to wrestle that machine by myself again )🥴😖😵

Thank you for this video!!! I did not have a manual for my washer and your video is the only one that had an identical washer even though my unit is a kenmore.

Thank you, thank you, thank you!!! This is EXACTLY what I was looking for! Went & bought all new springs because the used Kenmore I'd just bought (my old Maytag's transmission went out, more's the pity) was banging the sides of the machine like a monster was trying to get out. Yes. That bad. Once I took the cover off, the tub was sitting VERY wonky and all the springs looked good. I moved the tub and it seemed like it would move from one very off position to the next - never sitting properly. So I looked underneath and something didn't seem right. Mind you, I've NEVER worked on a washer before, but I could tell something wasn't right, so I came on here and searched - figured someone, somewhere should have the answer, and here you were! This is the EXACT problem. Now to to fix it. Thanks again!

@joshcobb4100

2 жыл бұрын

Great! Glad I could help!!

Thank you sir! The suspension plate was out less than 10 degrees. I realigned it & instant smooth operation. You saved me $600.

@joshcobb4100

2 жыл бұрын

Great!!

thanks, great observation, great tips, mine moved when I was replacing the coupler and I dint see that, thanks again!

Genius. Makes me wanna go out and pick up "broken" washing machines and "fix" them!

@iamthepapi6251

3 жыл бұрын

I do it everyday

@joeKisonue

Жыл бұрын

You should keep an eye out for these direct drive models

@aaronpowell1471

11 ай бұрын

Does it work for a whirlpool washing machine that is not direct drive?

Amazing. You saved my sanity. Been trying to figure this one out for a couple days now. Thank you.

@joshcobb4100

2 жыл бұрын

Glad to help!

After having exhausted all other options and stumbling upon your video and not verifying it to be my issue. I am damn near 100 percent certain this will fix

Greetings and thanks for this post. There's an imbalancing issue and agitating issue so hopefully this will help with an 80s series kenmore washer 🙏🏾🙌🏾🙌🏾🙌🏾

Been looking at other videos, after looking at yours, I can't wait yo pull my machine apart and take a look!!

Thanks very much, it helps a lot, I fix my washer shaking with your accurate knowledge.

Thanks so much for your video. This help me fix my mom's washer today.. I was going in there blind and she lives 40 miles away. This was exactly the problem..

Thank you so much. I was on my way to purchase a new washer for almost 900 bucks..thank God, I found this video.

@joshcobb4100

3 жыл бұрын

Cha-ching! 🤑. Glad I could help save you some cash 😊

Huge help! I recently replaced my transmission and motor and didn't have a balance issue before I did this now I know what to check. Thanks man! Liked, commented, and subscribed for this fix!

Thanks, this really was useful as this video help me fix my washer!

Great find! Fix mine fast after hours of head scratching!

You really saved us a lot of time and trouble! Thank you so much for this video!

@sandramccarrell8777

3 жыл бұрын

Suspension plate!

Right On Bro! I'll check that critical part out before I even assume it's the springs or the suspension rods

🤔 Most accurate & helpful advice so far, its worked perfectly 👍👍👍

Amazing! Thanks for the video. you do have the most accurate diagnostic.

Holly crap that's what was wrong with my machine!!! Thanks bro! Perfect video!!

You saved me a lot of aggravation and time. Thank you so much!

I was about to buy a new washer, then i found this video. FIXED !!!! Thank You!!!

@joshcobb4100

Жыл бұрын

Heck yeah!!!

100% fix! The skate plate was misaligned and after we re-algned it the washer works perfectly now! THANK YOU!!!!!!!!!!!!!

@joshcobb4100

2 жыл бұрын

You bet!!! Glad it worked!!!

Thank you for showing us, I appreciate it. I am a single gle mama attempting to fix the earthquake within

You are spot on!! All the others say springs, springs....thanks for settling the issue pal! Great work!

@joshcobb4100

3 жыл бұрын

I do what I can! Thanks!

@friedabacon3508

3 жыл бұрын

I have the same model washer with the same problem. I have been scouring the Internet for solutions, and they all say “springs, brackets, suspension pads, etc.”. So I removed my cabinet last night to examine these parts, and they all appear to be fine. I began to wonder if the springs could look fine while still being fatigued/worn enough to cause the issue. Also, I had to consider whether the problem is deep inside- maybe it’s the washer drive block, which would require much more disassembly than I’m capable of accomplishing. But now, thanks to you and this excellent video, I have another possible solution. Even if it turns out not to be the answer for my washer, many thanks for providing the solution for so many people!

Nice job and good explanation, I just rebuilt the transmission and it laying by it side did move these thanks for the info

Thank you soooo much, because my washer is very off balanced. I haven't taken it apart yet but was looking at a few videos just to get some ideas of what could be wrong with mine. And your video has to be the closest to what is going on with my machine.

Eternally grateful for this fantastic video.

Cool!! Thanks for the heads up.....I’m thinking I have that issue....

Thank you for sharing. Am having that problem with my kemore. I was about to throw out the washer. You just might save me lots of money. I will give this a try tomorrow. And I will update you if it worked

Josh . I followed part of what you just did on your vid . I’m in UK but got a really old whirlpool top loader . I’m talking probably 32 years old and had the symptoms you described but found a string on the floor once I’d got the cabinet off it was a thin spring one leg longer than the other . Put it back on after drilling a small hole IB frame so fingers crossed it’ll run ok .. your tips helped me a bit 👍

@joshcobb4100

21 күн бұрын

That's an excellent tip for that spring when the original hole rusts out. I've done this several times. Good job!

Thank you very much. Your video make my day succesfully. Problem fixed after a long day trying to figure out why it was jumping so much. Regards from Panama.

will surly try it on my whirlpool next week, you are the best

Thank you so much for sharing this video!! This was exactly what was wrong with my washer. You saved me some money. Thanks again!!

Thanks for taking the time to make this video.

Thank you, Mine is going exactly what you described.

I found this to be exactly what the problem was. Thanks

U the man ! Thats exactly what happens to ours. Wifey washed a heavy blanket and it through it off balance. Thanks !

@joshcobb4100

3 жыл бұрын

Those gosh dern blankets....I'm more of a fuzzy socks and HUGE electric bill kinda guy....

MAN! Not sure yet if this is my issue, but I just wanted to let ya know I appreciate you making this video! No fun repairing stuff that should work as intended, but at least there are nice folks out there like you to help us along the way! Thanks again!❤

@joshcobb4100

2 ай бұрын

We gotta help each other out and save that $$$!!

Thanks for this, I just replaced the clutch and must have knocked this around in the process! Also, I laid the washer down on its back and it took about 3 seconds to spin back around properly. This after fighting with my wife for 5 minutes trying to get her to lift it up enough to be able to spin freely.

@NickiMac

Жыл бұрын

thats great to hear, you didn't need help doing this then? I just changed suspension rods by myself and hoping this is the problem, I'm still getting lots of banging in spin cycle

Thanks for the info I have a washer that's doing that at this moment it was driving me crazy

You’re the goat for this video. Helped out tremendously, nobody has a video on this but you lol

@00tonytone

2 жыл бұрын

Isnt that plate called a skate plate. Anyway I seen another video on tilted tub. Mine is tilted forward and some of the water is spilling behind tub . Anyway the other video took the pump and motor out way then lifted tub with a piece of wood to freely align skate plate. I like your way better, get the wife to earn her keep and lift tub.

Man, I enyoyed your video and was laughing all the time cause it sounded funny but accurat at the problem. You described exactly my experience triying to find out what was the problems since the suspension rods seemed to be fine. Josh thanks a lot, from Puerto Rico.

@joshcobb4100

2 жыл бұрын

Thanks for watching!

THANK YOU!! Awesome find.

i bet that's my problem. Makes total sense. I was thinking same thing it's not the springs.

Ok thanks I am going to check it now

Thank you for this my guy. It was driving me crazy

Thank you for your videos! These DIY repair help me keep my rent down. My landlord will use any expense he incurs to raise my rent.

Thank you for the tip. I will look into it and put a comment what it was. Thanks.

Thanks, I had same problem, your video helped me , I fixed it it , working fine now 👍

Been scratching my head have changed everything thanks fo the info👍👍👍👍👍

Thanks a ton!!! I’ve done all the springs and shocks and the washer still smashed around. Got under it like you said and whadda ya know, the stinking plate was off just like you said. Got er lined back up and now it spins like a top. Thanks again

@joshcobb4100

6 ай бұрын

Awesome! Good job!!

Your the man finally a video that help me out thanks

Appliance parts pros could even help me after I had purchased and replaced bearing, seals, and a transmission for spin noise (separate issue). But was stumped with balance issue and couldn’t help. Thanks for the video, it was a big help!

@joshcobb4100

6 ай бұрын

Awesome! Glad it helped!

Thank you for explaining it and not making a really long video very helpful

@joshcobb4100

3 жыл бұрын

I try to keep em short... but sometimes I talk to much lol.

@joshcobb4100

3 жыл бұрын

I'm typically the shortest....wait....

Thanks. You helped me fix my Estate washer for free.

Gonna check mine tomorrow. THANKS!

I’m going to check that, my grandson checked the springs and they were all ok but still way off balance. Thanks, I will comment again to let you know.

@joshcobb4100

Жыл бұрын

Awesome!

The kenmore series 70 has 3 plastic sleeves that hold a steel pin. The pin goes through the skate plate and frame. The sleeves originally had something like foam or similar that kept pin in place on skate plate. I repacked the sleeves with cotton to keep pins from falling back into sleeve and allowing skate plate to move around on spin cycle. The horrible shaking on spin stopped. Our machine is 31 years old so whatever was originally in those plastic sleeves disintegrated and disappeared over time.

Ty so much for this vid. I just replaced my outer tub and all the springs on my old kenmore and yes these old school machines are definitely the best longest lasting washers out there. Anyhow my drum is slamming violently to where u gotta kill the machine before it wrecks itself. I'm going to check that floating plate deck and see if that's my issue. I will definitely let you know ...again ty so much for this super awesome video