I added a pre-order link for the prototypes in the description.

@emiliazielonka1609

Жыл бұрын

Hi, do U have sth similar works with MOCCAMASTER Cup-One ?

@sammyhaidi6807

Жыл бұрын

Is the stainless steel version available

@sammyhaidi6807

Жыл бұрын

Is the stainless steel version available

@tommyadams1640

Жыл бұрын

Just making sure the shipped version is the half inch longer version?

@kevinboger9531

Жыл бұрын

I’d be interested in the final stainless steel version when available

I would for sure buy a final version of this. This is my ONLY complaint about the moccamaster. Will you make a custom brew basket cover that fits this, too, or planning to leave this as an open design?

@alrui

6 ай бұрын

I have the same question🙂

This is very exciting to me as I just purchased the Technivorm Moccamaster 79112 KBT this afternoon! My sister-in-law has one, too, so I will purchase two of these the minute they become available. Congratulations!

Damn this was the only reason why I was hesitating from buying a moccamaster and looking to make a 3D printed shower head. Can't wait!

I will 100% buy the production, steel version of this. Hope it comes soon as I just finally picked up a moccamaster after years of contemplating it

Just got a KBGV and I can't wait for the final version of this!

You’ve subsequently created the Moccamaster 2.0. Simple yet so brilliant. Clever work.

This is an exciting and long overdue modification. Many of us Moccamaster users appreciate your time and effort. I have a few questions: 1) Is the prototype material safe especially after near boiling water passes throught it? 2) Have you tested the water temp exiting the stainless steel version of your new showerhead? 3) Does the increased weight of the stainless steel affect the seal and stability of the showerhead at the joint where it attaches? 4) Have you considered a redesigned basket lid that fits over the new showerhead for aesthetic and heat retention concerns? Many thanks!

Good idea. Will buy one when it's made out of a material that I consider food safe. There's no way I would drink even one cup out of the 3D printed version.

Ordered my first Moccamaster last night, and stumbled upon this video while in search of recipes… subbed to your channel, and will be ordering one of these! Very cool stuff, thank you.

I love your idea with the adjustments mentioned. I do think you need to add the lid as well. Excess steam can be hard on the cabinets above.

@DaryleTilroe

5 ай бұрын

The heat loss is also significant.

Better Coffee through better brewing, nice job guys!

Wow, I’d 100% buy. Keep us updated when it’s available.

I'm sure that the steel version will be heavier, especially at the shower head end. If it end up being too heavy and causing imbalance and losing seal around the tube, possibly a simple cross shape will help to increase basket coverage while decreasing mass and weight of a conventional round head. Flow can probably be evened out with variable hole sizing to promote water distribution to other areas.

@fredbloggs6080

Жыл бұрын

Titanium.

Excellent! The shape looks similar to the brew head on the Brim coffee maker. I’m interested in buying one once it’s made in stainless steel.

Awesome idea! I've been on the fence between purchasing the Moccamaster and 2 other drip brewers for a couple of months. Your innovation solves the biggest issue I have with the moccamaster. Thank you! I will go ahead and purchase the moccamaster and your drip spout! Research on new coffee maker, done. :)

I'll take the final version. Love to have it. Does need to be centered in the middle of the coffee..... but looking forward to getting a taste of the new brew.

Just wondering if you’ve sold any of your new design water brew heads? It’s been in the pre order state on your web site over a year

If you put this to market I will absolutely buy one I think the shower head opening so you can clean the back of the holes is a must have in my opinion

I think a fully transparent plastic (perhaps the same plastic as the water resevoir) would be cool - it’d match the aesthetic, and you could see the water move through it the same way it bubbles up through the centre of the reservoir when it boils.

@fallyn2920

Жыл бұрын

it wouldn't hold up overtime when calcium deposits build up. Being a visible part it might actuall detract at a certain point. This would be more easily remedied by extending the glass pipe that is fed by the heater towards the rubber gasket that holds the showerhead in place. This however is too brittle a material at such a critical point in the machine. What must also be considered is that this showerhead won't dry easily and could be a point for bacteria to accumilate if the machine is not properly taken care of. That said, i'd love a fully transparent machine for similar reasons.

@coffeehaus have you considered a plate that is on top of the basket instead of modifying the the arm itself?

Excellent work. Elegant design. Stainless steel indeed but I’d have the outside of the arm be coated in black to balance out the color of the entire machine. I feel like the polished chrome of the existing arm ages the look. Opens you up for color options for the arm in the future as well. Tight.

I was actually working/designing a Stainless steel version of this, but had issues with connecting to the glass tube. What kind of plastic did you use? Does it ‘off gas’ anything dangerous? * good job!!

3 questions What was the wattage/temp on the older version on the low burner setting ? What was the wattage/temp on the old version on high burner setting ? Since the new version switch has half pot/full pot, I’m assuming the wattage/temp of the burner is always the same, what is it ?

I wonder if you could make a, I suppose, plastic attachment that simply plugged into the holes of the existing spray arm and redistributed them in a similar pattern to shower head you designed. It would make it a little lower and maybe not so elegant looking, but...

Would absolutely order! Love what you guys do

Great idea, definitely would purchase

Oh dang! I’ll buy one. I can do some testing and or some media/video as well. Feedback as well, I have a Moccamaster and have used it for a few years now. More even extractions, able to grind finer, higher EY&TDS. 👏🏾

I've played with making a showerhead for one, but just curiosity. Have you considered (or have a design) for a "blank" that one can drill their own holes into to experiment with hole sizes? Also with the MM I feel like the brew bed itself ends up shaped a little differently than a cone or flat brewer would be, and think it might be worth playing with an oval shaped shower head or rectangular one or a hole pattern that does

You can put me down for two, one in CO and one in AZ, as soon as you have them in stainless (or chrome plate). Another thing one buys when spending $300 on a coffee maker is the aesthetic of the industrial design. The less one is asked to compromise on that aesthetic, the more likely one will be to purchase your improved distributor design. Nice work.

That is about the only improvement that could be made to MM, Kudos!!!

I'd definitely give this a try!

I actually looks like it could still accomodate the lid as the disk portion drops below square arm portion, can you confirm?

Would the plastic version have better thermals over a stainless steel one? Another concern is getting the water hot enough for light roast coffee.

@oli_vn

Жыл бұрын

The stainless steel one might need pre heating for lighter roasts

How cool! This is the ONLY thing that I think is a flaw in that pot. Can’t wait to see these for sale!

I would definitely buy! Thank you!

I was just about to buy the Mocha Master because of the thermal double walled carafe.

I am considering buying a moccamaster and this has always been my problem. I am interested. Out of curiosity, with no pre-infusion on moccamaster do people find that to be a problem? I ask since other machines have it. Also, how close are you to stainless since I only see original on your website?

Will you make one or the Cup One? It has a single spout outlet arm, so it doesn't do the best of jobs dispersing the water.

Great idea, does it drop the water temp? Cause that is a lot of holes and opportunity for heat to escape. Thanks, :)

@jdgordon194

Жыл бұрын

And the drip basket cover will no longer fit.

Pls post an update, when the final products is available.

Do you have a showerhead for the MM Cup-One? I have been looking for something like this for their single cup system.

Does this work on the thermal carriage pot the same as the standard?

Does this fit the KBGT? I see on the website you list only for the KBGV.

I have one question in regards to my Moccamaster coffee brewer. Why does it keep shutting off and turning back on every few seconds while brewing my coffee.

What is the type of 3D printed material you used for the prototype?

Thank you for making a more laid back coffee channel.

Absolutely genius!

Did you consider making a replacement for the lid on the dripper instead? That could be made in plastic and I imagine that would be simpler and cheaper to manufacture, but should enable similar results.

I don’t see why this shower head can’t completely cover the area under it? Is there a reason why grounds should be exposed if no stirring is intended?

Your website is outdated from back in February. Is the stainless steel arm in full production now? And is this to be only used with out the basket cover?

Very cool mod. Can you fix the carafe? I have to poor so slow or its a mess!

It was surprising to make my first pot of coffee in the new moccamaster and realize how poorly water was dispersed from the brew arm. I had just ordered a replacement arm to tinker with when it occurred to me I couldn't be the only one with the same concern and landed here. While I think there are a couple of simple tweaks to be made (1. Longer arm than shown for sure. It's one of the short comings of the OEM. 2. The screw off spray/dispersion face mentioned would allow optional patterns / hole size and easy cleaning.) I just ordered a prototype to support the cause. A quick update....No word on the prototype shipping yet, but the OEM replacement arm arrived. I used an ice pick to tweak the alignment of the spray holes and was able to improve the dispersion a bit, particularly in shooting further across the basket, less so laterally, which makes sense given the direction of flow. I'm sure the replacement arm will be an improvement over this, but it's simple tweak I would recommend to anyone for marginal gains. Cheers.

@vidkidruss

7 ай бұрын

Can you describe your tweak in a little more detail? I'm considering ordering a spare arm and 'modding' it a bit.

Can you guys also make one for the Cup One?

What happened to your fix??? No one from this company ever answers questions messaged to them!

My new MM Select arrives tomorrow. What an outstanding idea. Sign me up ..

I'll grab one. Good job. My home made versions don't work very well

I love the concept. The reason I went with Moccamaster was to eliminate the plastic taste from coffee made with machines that have mostly plastic in the hottest part of the brew cycle. The copper element to glass riser tube to metal spout mostly eliminates this (other than the basket.) What do others think?

A thought inside the shower head ; is very similar to the Bodum Bistro pour over machine they have same shower head concept, with 3 v ends inside to make sure the water does distribute more evenly throughout the head.

Can you share with us whether or not the container that holds the water, can it be turned 180 degrees? In other words, to make it where the fill lines are on the opposite side they are on now. Reason is, we wish that the switches were on the other side too. It would work much better for us. They don't make that, but maybe we could flip the container around. i Also, it seems that we could cut a lot of the power cord off easily enough, by opening the bottom of the machine. My plus 6" from the maker. Don't need but say 10" max. Thanks for your inventions and channel. It's great.

How fine is the coffee grounds? Would you go expresso fine?

What is the ETA on the stainless version of this? Will you provide a 3D print file for the prototype?

@bradd3634

8 ай бұрын

I ordered this back in January. Is this still a thing?

Hi. Does this coffee maker make tastier coffee than the Cuisinart pour over/precision maker?

Would the half carafe setting work for 3.5 cups of water, or about a third of a carafe?

@fredbloggs6080

Жыл бұрын

Corrected 3 1/2 ounces to 3 1/2 cups of water.

I think that being able to take the head apart for cleaning is important. I'm on board.

The arm should be a little longer to center the hea. Also, the head diameter should be large enough to reach the edge of the filter. Stainless steel or glass would be nice.

Will these be for sale again in the future?

Did MoccaMaster put on stop on this? No updates after a year?

I noticed right away seeing video of the OEM sprayhead in operation that it was obviously not an optimal design, being too narrow and not centered over filter. I don't understand how they can have such a high quality machine in every other respect but overlook this obvious design flaw, and by reports, actual functional deficit.

@alpsskiman

Жыл бұрын

I don't know if it's true or not, but I've read Technivorm has resisted redesigning the showerhead out of fear they may lose their SCA and ECBC certifications.

@fredbloggs6080

Жыл бұрын

@@alpsskiman They did redesign it slightly a few years ago, adding a couple more holes and putting mounds around the opening of the holes, but it doesn't address the main problem. Customer service seems to be in denial about the need for improvement. I have been using the CoffeePilot spray head that sits on top of the coffee filter basket. I have the Select version, and brewing 6 tablespoons of beans with the water level on the machine set to half a carafe, which slows the brewing down, with the spray head in place, I keep the carafe out for 40 seconds to allow the water to build up in the grinds and the basket, and then put the carafe back in place to allowed it to drain normally. With the correct grind, this works quite well for me.

@alpsskiman

Жыл бұрын

@@fredbloggs6080 You are correct. I did buy the latest version of this showerhead for my Moccamaster. It's a slight improvement over the previous version. I was referring to a complete redesign of the showerhead that more thoroughly saturates the grounds.

@fredbloggs6080

Жыл бұрын

@@alpsskiman I know what you mean. I don't know why if they went to the trouble of retooling for that new shower head why they didn't do a full redesign, unless they were afraid it would negatively affect some parameters, but they could always offer it as an option. I think the CoffePilot shower head insert I mentioned works brilliantly to achieve the same effect. I don't know what the status of the spray arm and shower head in this video is because there have been no responses or updates about it being produced in its final form.

What about a brew basket lid that will fit over this design to prevent heat loss?

@fredbloggs6080

Жыл бұрын

I really don't think even the lid provided does much or helps much to improve the brewing. Now, if he could incorporate an infrared array along with the spray holes that might be helpful.

How can I buy one of the trial ones?

Any update on the prototype? This was posted a year ago. Is the pre order still active?

Is the stainless version due to come out?

Interested in feed back option

I’m glad YT suggested this vid. There’s a guy in Australia that makes a round shower head out of stainless steel but I think it’s cost prohibitive.

Would it work on the CDT Grand?

Anyone know a quick fix to the middle setting not pouring? Thanks

Any pointers for Cup-One?

Nice job. Finally! Makes so much sense. Can't wait to receive mine.PSYCHED!!!

WOW! I am about to send my Moccamaster back for the very reason the brew arm does not fully "shower" the grounds - a huge flaw that my Cuisinart with its "showerhead" brew head (integrated in the lid) wets the grounds completely - making a great cup of coffee compared to the terribly weak (IMO) result from the M'master. You guys have come up with THE solution - and adding about 1/2" to the new stainless version will put the shower head smack dab in the middle of the brew basket. HOWEVER, a concern might be that the longer and heavier stainless arm (the printed plastic one is probably lighter than the stock arm) will SAG, so it may need a tab on the bottom that will allow it to rest on the edge of the water container to prevent sagging. THOUGHTS? Thanks for the great idea! - LongJnSilver in "Historic Hendersonville" NC

Please clarify: MM brews to 205 degrees F, but you say the plastic brew arm can withstand up to 150 degrees F? Is that correct? I ordered anyway, but just curious as to whether I'm living on the edge.

@mattclifton7352

Жыл бұрын

Up to 150 degrees C. Which is 300F. Way hotter than any brew or dishwasher.

Concerned about the difference in the temperature when it actually comes out of the “9 hole”, verses the “cylinder. I would think that much surface area in the “cylinder” would decrease the water temperature right before it hits the coffee grounds. Definitely stainless, definitely make the neck longer, extra gasket on other end and screw on head as well. The screw on head stainless as well.

@Coffeehaus

Жыл бұрын

Temp tests show no difference in water temp out of the shower head, and an increased water temp on a “cold brew” (where the metal is room temp) Agree to all of your points and those will all be there!

Is this plastic food-safe? What kind of plastic is it?

Need a stainless basket option to go with!!

Please put me on your wait list for this unique brew arm😊

Is this for KBGT too?

When will the final version be available for purchase?

@Dzbiq

11 ай бұрын

I also want to know!

@michaeldeckert6023

11 ай бұрын

Truly believe This guy is a rip off and has our money. He puts up no updates and there is no phone number to find out what is happening. They answer no emails. Amazing to me that they can get away with selling mocha Masters with no phone number. I wouldn't buy from them with no contact. My mistake for sending my money in in at least them not updating

@Gannon14

11 ай бұрын

@@michaeldeckert6023 yeah. I don’t think he initially meant to scam anyone, however my guess is once he talked to manufacturers and got quotes for making the stainless steel versions, he realized they were too expensive to produce. Just my guess though.

Any updates on the stainless version? I just visited your site and the product page hasn’t been updated in a while. Would love to buy one. Thanks!

@michaeldeckert6023

11 ай бұрын

Truly think this guy is a rip off. Has our money and has no updates.

@nicks8026

11 ай бұрын

@@michaeldeckert6023 Ugh, that’s disappointing to hear. Hope you get what you paid for sooner rather than later.

Any chance of coming up with something similar for the cup one?

@LukeHasAVlog

Жыл бұрын

Working on that now

@ephat100

Жыл бұрын

only reason why i haven’t bought a Cup One is because of the current spout

@wanderingstar5673

Жыл бұрын

You may want to take a look at Coffee Pilots Shower Head for the One Cup. It fits over the brew basket and does not require removing the arm. I am more comfortable with that design as it won’t add increased weight to the arm since it is completely supported by the brew basket. I’m not trying to rain on anyone’s parade. I just feel more comfortable with a design that doesn’t alter my MM.

Bought Coffee Pilots Shower Head Insert for Moccamaster (Canada). Have you used and tested item? Price is the same. I have had excellent results.

@Coffeehaus

Жыл бұрын

That’s interesting. Good to know. We considered something like this during design, but did not want to prevent access to agitation or contribute any more to heat transfer. Our goal is to have this around 20 bucks when all is said and done. The prototype cost is high since it’s just a little sprint run for us…

@JBM101

Жыл бұрын

where I am in canada and have a moccamaster

@appleflamingogecko1657

Жыл бұрын

@@Coffeehaus lovely!

@wanderingstar5673

Жыл бұрын

Thank you for mentioning the Coffee Pilots Shower Head insert. Just ordered the One Cup attachment. Now my Moccamaster will be perfect.

Just ordered:)

Are your prototype spray arms still being shipped out and in one or two to weeks, and do you take PayPal?

@Coffeehaus

Жыл бұрын

I’ll be posting an update video on Tuesday with our new brew recipe - printing has officially began - we will be shipping out 6 shower heads a week starting this coming Friday (they take 20 hours each to make) - and the price will remain the same until the stainless steel version is released this spring. Paypal is available as an option through our website I believe - shoot us an email if you have any trouble.

@fredbloggs6080

Жыл бұрын

@@Coffeehaus Well, I just ordered the Select, from Amazon, which will be here in 2 days, they say. I guess I could order a prototype now and then order a stainless steel one later. I understand the stainless steel ones will be about a half inch longer to be centered over the filter?

@Coffeehaus

Жыл бұрын

@@fredbloggs6080 the prototypes will also be a half inch longer.

@fredbloggs6080

Жыл бұрын

@@Coffeehaus Oh, that's good. How long should the prototypes last, or should they be indestructible (and non-toxic I assume)? According to an article on the subject I came upon a few hours ago, there has to be balance or trade-off between water dispensing that agitates and sprays evenly, which may cause less agitation. I guess ideally it should have a little agitation with even coverage, enough to keep the particles suspended in the water. I wonder why no one has designed a spray head that has a turbine mechanism so the water flow would cause it to rotate in addition to spraying, or maybe it would be too likely to get stuck. Maybe the water pressure isn't sufficient. So you just put a little motor with a button battery in it. That's a joke.

@fredbloggs6080

Жыл бұрын

@@Coffeehaus I sent you an email a few days ago using the e-mail you give for feedback (not using my KZread channel email), asking about PayPal which I can't find on your website, but I have not received a reply from you. I've been experimenting with my moccamaster for a few days. At first I thought the problem before was the beans and then maybe the grinder, so tried a few different somewhat expensive grinders, but the problem turned out to be my several-year-old coffee maker although not obvious from the way it operated, that is, the water seemed very hot, but it was not making good coffee. The brewing time did seem to slow down, which usually means the temperature is not hot enough but I think the temperature was still hot, so maybe it was over extracting. Anyway after some experimentation with the Moccmaster I got some very good brews with my original grinder and coffee. I even tried at first to make a tube of four layers of aluminum foil with crude holes approximating those in the original spray arm, and fit and shape it over the original arm extending the new holes over the center, but I couldn't put the lid on. So I'm not sure how good that would be--there was less pulsing and more streaming. I think I tried it twice but didn't pursue it further--one thing I like about the MM is that it uses a copper heating element instead of aluminum. So far the best thing I found is to push the grinds in the filter away from the handle side of the basket, so the majority are under the area of the spray head holes, and shape it into a sort of plateau there. It does seem to get the grinds wet better but doesn't solve the problem of the rectangular channel, although the coffee does taste pretty good that way. I'm also experimenting with pushing the grinds on the ends of the channel into the center halfway through the brewing. Although it may be expensive, I think someone could design a machine with a spray head with a single spout that rotates like a pour over. I guess the water pressure isn't great enough to make it rotate on the same principle as a garden sprinkler. So if you don't have PayPal, do you have a phone number I can give you my card number over the phone--I just don't like putting it online? Is there a different email I should used to contact you?

I think the shower arm you are showing should be a little longer so that it evenly reaches across to the other side. It only appears to be dispersing water in a wider area from side to side than the Moccamaster's shower head, but doesn't quite reach across so that the shower drips just as close to the front of the basket as it does to that back of the basket.

I want one.

Phenomenal

i would love these if it was steel, still has to fit the aesthetic... but really love the idea!

So... here's one that I've not thought about. What about a version of this for the one cup version? That is so many different levels of worse than the big ones.

If it was stainless steel I would buy. One reason to buy the MM coffee makers is the limitation of contact between hot water and plastic. 🤗

Any update on the final version?

@michaeldeckert6023

11 ай бұрын

Amazing how this guy takes our money and does no update. I have waited since March and have not had an update but once. And I had to push email after email to get that. Do you realize there is no phone number to call? Amazing that somebody would buy a mocha Master or buy product from them with no phone numbers. A rip off for sure

@twozerosix206

11 ай бұрын

@@michaeldeckert6023 I didn’t pre-order. Sounds like they have a potentially money making item that people want to buy. Who knows.

It's been a year. Some respect for costumers with an update?