Друг спасибо тебе. Благодаря твоему видео понял почему у меня вибрирует вал. Ох уж этот магнит!!!

@TheAussieRepairGuy

25 күн бұрын

Да, допуски довольно близки.

I was looking to change the battery in a different clipper, but I have these ones too, so will save this video for when they die.Thanks!

Çok faydalı video olmuş teşekkür ederim kardeşim

Awesome vid. Thanks. What temp u run ur soldering iron at?

@TheAussieRepairGuy

Жыл бұрын

About 400c, and I use 60/40 tin lead flux core solder, 1mm diameter.

What is the battery size and where can I get one? I have the sterling mag but can’t find the battery!

@TheAussieRepairGuy

2 жыл бұрын

At 4:50 I state that its a "14550" which is the type of li-ion cell.

On Jaycar, I could find the following battery: 14500 Rechargeable Li-Ion Battery 800mAh 3.7V Solder Tag Is that the correct one?

@TheAussieRepairGuy

Жыл бұрын

Yes, a highee capacity is fine as long its the 14500 size.

👍

Please tell me what battery you used. If you have a link to purchase, even better

@TheAussieRepairGuy

Жыл бұрын

14500 size 800ma li-ion with solder tqbs.

just replaced the battery on mine and something interesting happens. After 15 minutes of charging the blue LEd switches off. How come is this happening? I''m sure it would take longer than 15 minutes to recharge a battery. Any ideas? Cool video by the way, it is very helpful.

@TheAussieRepairGuy

Жыл бұрын

It could be that the newer battery is alreasy partially charged. New batteries iften need to be discharged a couple of times to reach design capacity.

@miguelfernandes333

Жыл бұрын

@@TheAussieRepairGuy you could be right, it was partially charged I fully discharged it. Still, something is off. The motor might not be working that well as the change of battery didn't seem to help that much, it feels slower and rotating at a lower frequency than my new Wahl Beret.

@TheAussieRepairGuy

Жыл бұрын

@@miguelfernandes333 perhaps a small drop of sewing machine oil on motor shaft bushings

Why did you skip the disassembly? I have Model 9876L which has no screws showing, so I'm assuming that I have to open the casing with a knife edge, which often destroys it when you don't know exactly how it is held together.

@TheAussieRepairGuy

7 ай бұрын

See 14:00 onwards for re-assembly, might help you understand how it went together. So I got out of bed just to look this up, I never recorded the disassembly, there are 5 very obvious phillips screws under the lower cover. separate the silver bit from the black bit and they will be very obvious, DO NOT try to pry the whole unit apart.

@woody1797

7 ай бұрын

@@TheAussieRepairGuy Will do. Thanks for the reply.

@GmanInd

4 ай бұрын

@@TheAussieRepairGuy thank you for this video! I didn't think the black part was under the silver, I thought it can off to expose screws. I have the same issue, where to insert a pry tool without wrecking the clipper, while examining frame 12:52 I saw the black plastic fingers in the cutter end that cold be pried out to start the cover reveal, a pry in the lower part of the switch hole and prying out on the silver cover at the charger end got it off.

@TheAussieRepairGuy

4 ай бұрын

@@GmanInd Yes this video was done a few years ago and I was in a bit of a rush, and the owner was observing as I did it, consequently I missed filming a few steps.

U know that annoying aluminum shaped like a U once you open up the blade? It fell out. But, now I don’t know where it goes?

@TheAussieRepairGuy

3 жыл бұрын

Sounds like retaining clip. I don't have these in my posession anymore, and I'm not an expert on them. My suggestion would be to assemble the unit until it becomes obvious where that part belongs.

@or1946

3 жыл бұрын

@@TheAussieRepairGuy you have a wahl mag, right?

@TheAussieRepairGuy

3 жыл бұрын

@@or1946 no this was handed to me for battery replacement - I did the video and gave it back to its owner.

@or1946

3 жыл бұрын

@@TheAussieRepairGuy ok. Damn, I wish I knew how to put it back. It’s so Frustrating ( it’s for a Wahl Mag Trimmer ) Anyone know?

@TheAussieRepairGuy

3 жыл бұрын

@@or1946 this guy seems to go into detail that might help: kzread.info/dash/bejne/noarssWzmqvXdag.html

Yeah but you don't show how to open it

@TheAussieRepairGuy

3 жыл бұрын

I'll go back over this when I'm not 300km from home, and see if I can elaborate. However I don't own this, nor is it in my posession now.

@TheAussieRepairGuy

3 жыл бұрын

Off memory, I just undid screws and popped the snap clips on the body.

Wahl. Ka. Tirimr. Silo hogeua. Kru

Why you don't describe the real problem. The contact was broken or bad. Typical Wahl. All those Beret pro trimmers has the same problem.

@TheAussieRepairGuy

2 жыл бұрын

Probably because these had been in my hands for a total of 5 minutes at the time. Why don't you make your own video where you cover these points yourself?

Such annoying skills

@TheAussieRepairGuy

2 жыл бұрын

I'm glad I don't exist just to entertain you.