What do you think of this new Wago? - Check them out here: amzn.to/3SQgNrf

@InconsistentManner

6 ай бұрын

put the meter in circuit with the power you should see a voltage drop.

@TomCee53

6 ай бұрын

A bit pricy, but probably worth it. Fortunately, you probably only need a few.

@radian2323

6 ай бұрын

holy cow. It's $26.

@FennecTECH

5 ай бұрын

Please put some on your roof. I want to see how these handle a year of sun and rain and weather they remain water proof.

In-ground irrigation valve boxes was my first thought. Then I realized that Waterproof Wagos will cost about $8 per connection, whereas generic wire nuts filled with automotive grease cost 10 cents and outlast the valve solenoids. In-ground lighting is probably a better application.

@ikemkrueger

6 ай бұрын

For that money I would go with silicone.

@arion_vulgaris

6 ай бұрын

@@ikemkrueger which can be acidic and thus corrosive

@xenuno

6 ай бұрын

@@arion_vulgaris Only when it's curing and also .. your not putting paint buckets of it on your connections. Have you ever used silicone before? I have and seen old silicone ... there was absolutely no damage to whatever it was touching

@anthonywilliams7052

2 ай бұрын

The link in the video shows $26.35 per box! It looks nice but seriously $26? Only 4 for $100! For that I'll stick to heat shrink tubing. I'll add some RTV or silicone if I want to submerge it.

During the 1990s I worked for a company that represented Wago , both companies on that time under the umbrella of the british holding "Bowthorpe PLC" . I introduced in some territories Wago products , mainly industrial conectors\interfaces with so called "Cage clamp" [ spring connection instead of screws ] technology . Wago has been innovative for a long time , I can recall there were many different things going at the plants of the company in Germany , including what may be considered a prototype of a small box to protect splicing connectors.

Holy moly, you weren’t kidding when you said “not the cheapest”! I just checked them on Amazon 😵

@harborcbs

6 ай бұрын

$7.50 a pop. No thanks.

@chrisryan3445

6 ай бұрын

@@harborcbs Cries in £ - about $9 - $10 here at the moment per unit.

Wagos are so awesome they make fixing Outlets way easier.

@Dinco422

6 ай бұрын

ONLY IF your conductors are not made from aluminium.... otherwise oxidation / corrosion will occur.

Love the WAGO stuff, but my two electrician friends are old school and can’t get past their ingrained belief in wire nuts. I’ve wired a ton of houses for them, using nuts, but I use the WAGO’s now for everything. Cool waterproofing for all my irrigation and pond lighting.

@UhOhUmm

6 ай бұрын

Your electrician friends should visit something beyond their local department store. Take any modern industrial cabinet and it will be filled with thousands of push in or other lever style connectors, including incoming supply. Phoenix contact make a terminal block that takes up to 95mm2 (0000AWG, what a stupid measurement system) wire and is 232A rated (lever) or 16mm2 70A rated as standard push in (no lever). edit: Actually they make an ever bigger one, I just haven't seen one in real life PTPOWER 185 is 309A rated.

@thecodingchicken

6 ай бұрын

​@@UhOhUmmawg ends at 1 awg I'm pretty sure. After that we have 1/0, 2/0, 3/0, and 4/0. After 4/0 (4 ought) it goes to 250mcm

@TAGUPNBLUE

6 ай бұрын

You probably never were in the electrical trade doing this for a living sleeping at night knowing you did a best job you could that you didn't wire for fire show me at the UL listed no respect for proving wiring methods and no respect for electricity

@professorg8383

6 ай бұрын

Hate the WAGO stuff, but my engineer and electrician friends are old school and can’t get past the well proved superiority of wire nuts and the potential high resistance issues of WAGOs. I’ve wired many electrical circuits, industrial and residential using wire nuts, but I won't use the WAGO’s for almost anything except very low current small wire connections like in light fixtures. OK waterproofing concept might be useful in very moist areas. Although these may now be listed for use in the US, make sure you don't use the IEC ratings!! UL ratings are considerably less that IEC ratings. Too many people assume ratings are universal,. They are not!! Specification standards between IEC and UL, NEMA and NEC, are very different. What IEC EN standards allow are not acceptable to any US standards.

@professorg8383

6 ай бұрын

@@UhOhUmm Any modern industrial cabinet?? You mean global stuff built to IEC standards, Virtually none of this is NEMA approved. But industry can put in whatever they want because they assume liability for the installation. They decide what spec they want to build to. Corporate bean counters make the purchasing decisions and low cost always wins. Additionally, most equipment suppliers build to IEC specs because the stuff is cheaper, smaller and need less labor to assemble. Buy something off the shelf and it's IEC rated and not NEMA approved. Very few US equipment manufactures build to NEMA spec and it's almost always custom. When you quote a rating, you need to clarify whose rating that is. IEC ratings are junk! You'd be a fool to use this junk on any critical dangerous process. If you have a critical/dangerous process, you're better off to build to custom NEMA specs. Just because this stuff dominates the global market, doesn't mean it is as good as the old standards. I've seen enough of this junk in 50 years as an electrical engineer in heavy industry. In the end corporations look at cost of the equipment vs cost of failure. If the cost of failure is likely to lead to loss of life, the calculations change. When the risk is some damaged equipment and maybe some production loss, it's probably tolerable. That's likely to fit 90% of applications. But this stuff is not very good for heavy use and when it fails, it fails catastrophically. .(it blows up!) But it's cheap, albeit over priced for what you get. I really hate the stuff except for low power use like PLC and control module stuff. But you do see a mix of levels in some of these equipment cabinets which is a disaster waiting to happen. The plastics they use don't hold up to high energy faults and will burn like it's drenched with kerosene! I've seen some of these panels completely burn down from a fault that should have been sustainable. I know this stuff is compact, and easy to wire, but that doesn't speak to long term reliability. My guess is that you don't own and maintain this stuff, but wire up installations. But it's a different story when you have to live with it!

The reason the GFCI didn't trip is because the short was through the neutral so there was no current differential.

@postergmail6202

6 ай бұрын

Yes. We know.

@emmettturner9452

6 ай бұрын

Yeah, he mentioned that.

@CharlieTheMost119

6 ай бұрын

Should have thrown a ground into the water as well. Should trip right away without the clamshell. Shouldn't trip at all with it.

@kbud3442

6 ай бұрын

@@emmettturner9452actually he said it was because there was no ground… which is false.

@emmettturner9452

6 ай бұрын

@@kbud3442 Did you even read what you just wrote?

Thank God they started making Wagos, because there are too many people that don’t know how to connect conductors, and this allows those without any wiring skills to get a job done.

Excellent! I never heard of these before. I will definitely get some. Thanks for the info my friend.

@SilverCymbal

6 ай бұрын

Thank you very much

Awesome find, I can't think of any applications currently, but now when the not suitable for wet thought goes through my head when picking up my box of Wago connectors it will be followed with these gel boxes

Been an industrial sparky for 50 years and we had two 100 HP 480 volt motors in a pit that got filled with 6' of dirty water at least once a year. I would tape bugs with garnished Cambridge tape ( not waterproof like rubber or silicone tape ) then at least 12 wraps of Scotch 33 tape down at least a inch on wire insulation. Motors were TEFC ( totally enclosed fan cooled with a rubber basket on cast iron pecker head. Motors would continue to run submerged for at least halve a hour until winding shorted out. Even used wire nuts on 480 volt control wires that were covered in a few inches of water but taped in same matter and never blew a fuse.

Wago solving problems. I like them and started using them. I think Wago should make a multi straight thru connector for things like connecting the multiple wires between an A/C unit and the thermostat. Seems like those connections are always rats nests.

Thanks for sharing all the best possible details 👍🏻👍🏻 Subscribedddddd❤

An amazing product made even better.

No way!!!! This sounds amazing!!!

This is really really cool. This is one of the big features that the WAGO 221s were lacking, and now it's available in what looks like a really well done form (I love the fact they even appear to have one designed for the inline connectors too). Still not as convenient (or cheap) as the "jelly bean" connectors for things like sprinklers, I think, but I could definitely see using these for an extra layer of protection when dealing with mains-voltage connections in potentially wet areas, or when dealing with some low-voltage higher-current applications (such as low-voltage outdoor lighting or vehicles)... A much better way to test these would have been to: 1. Measure the current flowing through the supply wires before and while they were put in the water. 2. Place a ground lead in the water, which should actually cause the GFCI to trip (and is a better test of the sort of water-ingress scenario you really want to prevent happening, particularly on a non-GFCI-protected circuit).

Always useful information thx 🙏

Maybe the better way to test for voltage leak would be to put the hot splice in the water and then measure voltage from the neutral wire to the water. You might pick up a couple millivolts of inductance, but any more than that is a good sign it's leaking.

@andrewt9204

6 ай бұрын

@@bountyhunter4885 I'm not sure what the UL testing requirements are, but I assume they would have done some sort of continuous weatherproofing and temp cycling tests. I think these would be good for somewhere that might have moisture exposure, rather than guaranteed exposure. Unless you're running low voltage where a leak won't cause dangerous situations.

WAGO are the best connectors out there. And now they’re even better!

Very concise and informatic video

Just used my first Wago last weekend (hard to find the real deal) and I am sold and they are now my go to. A waterproof version is great !

@RFC3514

5 ай бұрын

Hard to find? You can buy them online at hundreds of websites.

These look cool. I've been using the 3M moisture lock connector or 3M Electrical IDC (Insulation Displacement Connector) with good success for landscape lighting

I mean in a vs neither wago or wire nuts are waterproof but glad to see wago stepping up and creating new products 😊

Wow .. interesting! Thank you!

This is pure genius.

Another way to test. Leave the neutral wire out of the salt water. Put a WAGO on the hot lead and a second WAGO on the other hot lead with no connection between them. Put both hot leads in the salt water. With a low wattage bulb (10 watts or less) you should see a dim glow. If your Fluke meter measures AC current you can check the current through the bulb. Then add a GELBOX to only ONE hot lead and dunk again. There should be less than 1 ma current flow and the bulb won't light. Some vinegar may help make the water more conductive.

I can see myself using these for automotive use for sure.

I use to work at a theme park and we had to hook up switches under water would love to see how these would hold up in that environment we did several experiments to find the best solution for us it was fill a but splice with silicone and heat shrink over each wire then heat shrink over all of them that would hold up pretty well

Yep not trying that anytime soon fantastic 👍

These look conceptually similar to the Volt Lighting Micro-Junction and Nano-Junction connectors, which I've used for my landscape lighting. Definitely a heck of a lot better than the gel-filled wire nuts! I assume the Volt ones aren't approved for line voltage, since they're sold for low-voltage landscape lighting. I'll have to compare pricing and maybe switch to the official Wago version if it's comparable, since those seem a bit more vertsatile.

@SilverCymbal

6 ай бұрын

You are 100% corrrect. Volt brings them in and low voltage is exempt for approvals. While of course they work fine, its great to see these for higher voltage stuff too.

@julianreverse

6 ай бұрын

Because they are 100% knockoff of the original Wago lever connectors.

I have used something similar for direct burial LAN cable splices... usually where the homeowner left it on the ground instead of burying it and animals got into the wire.

Thanks!

That is crazy testing. Won't catch me doin' that. There are also relatively new things like silicon putty and Flex Seal products that you might find to find ways to use. For instance, those cheap PWM charge controllers I like to use on my lead acid car batteries want some extra insulation and water protection where you shove the wires in and screw them down (it helps to mount the controller on a piece of wood, too). Or those sprinker situations. I like the boxes, but there are options. In any case, wago type connectors are way better than those screw in wire connectors

been using a very similar product for years in the cable industry for coax splices.

I seen old fashioned wire nuts with the gel already in it for outdoor uses. But for the rest of the trades, I have a not so well kept secret, that were best kept from the customers. Customers do not get a good job, but only to code minimum sometimes (sometimes below), not because we do not know how to do a good job, but because we do not want to. On the job, usually one price were given, and the faster we get out of there , to the next job, the better. To do a good job require organizational skills, not everyone have it. When I did outdoor light fixtures, I used aluminum corrosion inhibiting compound in the wire nut, and when done, I seal the bottom with more compound. Bosses often refused to buy the compound or do not want you to take the time to use it. Those joints can easily last over a year and that is all they are responsible for. Ilsco make a compound that is not as messy to use. Why take more time to piss off the boss and the customers do not appreciate?

As you say they've been in Europe for years, I've not had much call to use them but the one place I have is to replace a terrible junction box setup that was used to install the cabinet lights in my kitchen, so unlike the installation that was there before they're moisture (i.e. steam and grease) proof. There's one downside to them - the 221's have various test points on them which is super useful when you're doing electrical testing, to use those test points you then need to remove the gelbox which effectively destroys it; you probably could reuse it if you're careful and maybe it'll reseal around where you shoved sharp/thin test probes in, but you'd probably lose all hope of maintaining the 'official' rating.

Snap on tool box? Thats how you know you made it in life.

I've used the gelled wire nuts for my low-voltage landscape lighting. Can these be buried as well? If so, they're perfect!

Very cool!

Damn, $7-13/each. Steep, but not atrocious. Thanks for letting us know about these!

Love the Wago brand!

@SilverCymbal

6 ай бұрын

They are pretty smart cookies over there

A similar product has been used for traffic light loop detectors for decades

It would be great if Wago would add in some strain relief to make in line splices for Romex style cabling. Tycon did it but the cost of the splice connectors was insane.

Nice toolbox

thats pretty rad. i dont use wagos generally, but when i want to water proof, i usually do polyurethane, but while its not cured, the solvent is highly flammable and will ignite so do not listen to me ;)

You should see how wires are spliced in Taiwan. Miles and miles of electrical tape, no wire nut to be found anywhere. Outlets in bathrooms with tape over it to "protect" it. No ground at all (they do not exist, and wires to allow ground also do not exist). But the ironic thing is, WAGO 221 exists here, but is a little expensive.

Ideal makes a direct burial wire nut as well as a less extreme weatherproof version that gives above grade moisture resistance. Worth a price comparison at least...

I think they should make a product for trailer wiring. Seems like one of the biggest wiring pain points.

The Gel box is single use then right? Or can you repack it after peeling out the connector for reuse?

Great video, analysis, and you know if you're getting good meter results... it's gotta be a Fluke. I'm wondering how well that gell will do in Arizona's 110°F sun, but if it's in an enclosure likely not a factor. Thanks again, upvoted, and have a great weekend! Ehud in Tucson

That is one serious toolbox.

@SilverCymbal

6 ай бұрын

Thank you, its almost 30 years old. Bought it used almost 15 years ago, they cost about 5x as much now. Truthfully the ICON Harbor Freight ones are better. I would buy one of those now if I was replacing it,

@JAYJAYJAY53

6 ай бұрын

@@SilverCymbal That was going to be my reply. Harbor freight has stepped up the game in the few years.

Using two water-proof covers doesn't double the chance of detecting a failure, it halves it. Both have to fail before you see any bubbling.

GFCI don't need a ground, it's not tripping because current it flowing between L and N which is normal a GFCI trips when the currents in L and N are unequal meaning there is fault current flowing elsewhere.

Great video, thanks. Layman here but couldn't you put a watt meter on the connection and if there was a short in the water you would see increased watts, rather than just depending on a visual indicator?

Looks like they are super sweet. But not cheap

$30 for 4 on Amazon definitely not cheap

@shazam6274

6 ай бұрын

PLUS the Wago connector! So around $10 to connect 2 wires together! Insane! Amazon has all kinds of 600V waterproof UL wire nuts for ~ $0.75 ea.* Wago: electrical connectors for people who should never even think about doing electrical work. Coming soon: Wago connectors with Bluetootth and an App? * Low Voltage ones for less than $0.25!

@sm1thers

6 ай бұрын

Yeah but the cost of something going wrong is loads so Wago gets my money. If you are DIYing then you are saving so much its worth doing it right with WAGO, If your doing it Pro then the labour is so much a bit of money on the wagos is negligible especially given the time saved

@tedbell4416

6 ай бұрын

​@@sm1thershow many wire nuts have you seen fail ?

@sm1thers

6 ай бұрын

@@tedbell4416 none, because I live in the UK where they are banned.

@shazam6274

6 ай бұрын

@@sm1thersSo you're saying the billions of wire nuts used which, cost several cents, and are everywhere (including in your home) are sub par and not "right"? 😂😂🤣🤣

What's the shelf life rating of the encapsulation box? And are there any statements on whether they can withstand continuous UV exposure? Seems like it's a pretty useful product for certain outdoor scenarios.

@SilverCymbal

6 ай бұрын

They claim its unlimited for the shelf life, as far as UV, I haven't seen that listed but they can be buried, but again remember electrical code prevails for high voltage uses, you will likely still need physical protection.

What about measuring voltage between the water and a ground terminal during the immersion?

The telephone and cable companies use something like this in my area in Canada. I think they call them clickets or gel splice connections. They use them to make connections in wet buried areas.

@cfusername

6 ай бұрын

Yeah, I think they are made by 3M, but also cut into the wire and cannot be opened up again. There's some gel inside that completely surrounds the point where the wires are connected through the metal clip.

Are you able to use regular Wagos with different stranded metal wiring (aluminum with copper) or stay away?

Love the Wago series P.S second?

Your recpticals are upside down, remember ground down. 😊 Otherwise great video.

Excelente

2:49 Great video. However, by using 2 connectors, you have actually halved the likelihood of failure, due to your testing methodology. In order to see the effects you are looking for, there would need to be a leak in both connectors at the same time.

$7-10 a pop. I'll stick with gel filled wire nuts.

Are they certified for explosive atmospheres?

Anyone know what the "gel" is? I can't find a MSDS to see if it's chemically inert or not. Says silicone-free but no other details. In particular it would be nice to know what the temperature resistance is and if anything toxic is released when it burns.

Nooice! 😎 STOC

It would have been a bit more compelling with a ground wire immersed in the salt water, or an amp meter during the test before and after the gel box. But, the point was made, sufficiently.

If it's water-proof, I think what's inside is supposed to NOT shock me.

Those bubbles were H2 and O and since it was AC, the H2 and O was generated by both wires, alternating at 60Hz. The electricity was breaking down the water. Would have been interesting to see the current draw on that circuit, maybe 10A based on the humming.

6 ай бұрын

Actually H2 (hydrogen) and Cl2 (chlorine). In salt water most of the conductivity is provided by the salt ions. The cathode would reduce sodium (Na) to sodium metal, which instantly reacts with water creating sodium hydroxide (NaOH) and hydrogen (H2). The anode oxidizes (removes electrons from) the chlorine ion, producing chlorine gas, which escapes as bubbles directly without reacting with the water much. If you wanted oxygen, you'd have to start eg, with sodium hydroxide solution rather than a salt solution.

6 ай бұрын

And eventually the water would simply start boiling because of resistive loses being a large part of where the energy gets used at line voltage in a case like this.

I’ll be the first one to address the elephant in the room. Did you purchase the most Ginormous snap on tool kit or are you shrinking??? Lol As always you have the coolest stuff. Can’t wait to try them.

I first read the title as "Waterproof Wagyu". Imagine my confusion.

I haven't found anything that says these are UL listed. Anyone know otherwise?

Should have used an insulation tester with a test voltage of 500V or 1kV. But I can assure you that it will be ok. Always use the smallest gel box possible or the displacement of gel might not be enough to seal everything up.

@jensschroder8214

6 ай бұрын

What can be used for 250V AC in Europe can certainly also withstand 120V in the US. You need to take a separate gel box for phase and neutral.

Are the gelboxes reusable?

Water is an insulator. That's why it shorts out circuits. It doesn't allow current to flow.

At almost ten bucks a pop THEY CAN KEEP THEM! Wire nuts with RTV is still valid.

Finally

Gel boxes are really common in the UK, where water is, er, a problem....

What is the name of this gel?

I love the Wago way, but I'l keep using my Polyolefin until the costs come down.

It'd be better to have an ammeter in series, because it'd show immediately, if there is connection through water by current value rise. Also, I'd like to see how resistant are the to heat - what about boiling them in salt water for one hour? It should be able to handle temperatures -55 … 85, has anyone tested if it's actually true?

Could you not get a 3d printer and make custom boxes along with just stuffing non conductive silicone in it? Seems much better for hobbyist/DIY, $8 per connection seems a bit much. I'm in the UK so I can't do electrical changes technically by law 😅

I imagine that you should do your best to center the wagos inside the housing

I'd think about installing an RCD if I were you

A much more economical option would be solder sleeves it what’s used on airliners so if they’re good enough for commercial airliners it’s more then good enough for home use.

@SilverCymbal

6 ай бұрын

I did a very popular video on those: kzread.info/dash/bejne/gI6o2aaYdprShKQ.html and they are wonderful for low voltage permanent fixes. They aren't approved or useful for high voltage applications and while an airliner is of course amazing those lines are all lower/voltage amps, where home high voltage wiring needs different connectors.

@P-47D_theJug

6 ай бұрын

Very true

There is a similar slightly larger product that is used when repairing buried telephone service wires. They work pretty well.

thats one sexy Snap-on tool box you got there.. LOL

similar to this has been used in telephony cables repair with goey stuff preventing moisture/water to creep inside so it is not a new thing at all just a new adaptation

@blimm2341

6 ай бұрын

Similar to a coax splice as well. Been around for a while.

That gel looks like the glue in Glue Traps🐁🐀

Im self-teaching myself about electronics right now, and ive learned that hot glue is a really good way of making connections water resistant. Why would I use this instead of a hot glue gun?

Wago may be in the new codes requirements my home is too old.

Excited up until I saw the price per unit O.O!!

@SilverCymbal

6 ай бұрын

Yes, definitely save for your problem connections that you can't afford to fail.

They should use these in the parking lot light poles.

@SilverCymbal

6 ай бұрын

Definitely a great idea for those They take a beating.

👍👍

“In some situations, these will be *Ideal*” UHM ACKSHUALLY THEY’RE WAGO

3M has been making gel-based Scotchlok wire connectors for decades. They are a simpler one-step process than these Wago's, as they don't require the cover piece. They probably aren't as water tight as the Wago's, but work perfectly fine short of full submersion, and are waaaay cheaper at 14 cents per connection, verse Wago's unreal $6+ per connection. I'd skip the Wago's unless you need full water submersion, and even then look for cheaper alternatives.

@SilverCymbal

6 ай бұрын

The downfall with scotchlocks is they have no ability to open them after, short of crushing the connector and hoping the mechanism doesn't damage the wire. That might be fine for some application, but at some point almost every connection needs to be opened, replace a light, change an outlet, etc. So while they have their place and do technically meet NEC, no one uses them for high voltage work due to the fact they can't be serviced. Remember these really aren't for underwater use, yes they can be but its for super tough environments with repairability. But I have used the little scotchlocks for decades on phone lines, where they work perfectly and are meant to never come off.

I'd rather use the silicone filled wire nuts. Those are removable. Whereas with the waterproof wago you'll have to cut the wires back.

Wait whats stopping me from taking a wirenut and fillingnit with silicon after twisting it on

@burtburtist

6 ай бұрын

Nvm lol turns out thats already a thing

@SilverCymbal

6 ай бұрын

Thats fine, but I would't depend on it since it's not certified for that use. But if the connection isn't a big deal you could do that or even wrap with self fusing silicone tape. The Wago is nice as its designed for this and I like that you can open it later and redo or change connections but they also are exactly .25 each so you want to save them for super important connections. I know an electrician who does a ton of work on Cape Cod. He uses these for some outdoor fixtures for folks in the ocean ares, not rich people just that get salty air hitting connections