Am an amateur mechanic but this is really gud,please produce more videos for us we can't afford to pay fees in high institutions to have this knowledge. Many thanks to you.

@vehiclemaintenanceandrepai3790

Жыл бұрын

Hi Krispine, nice to meet you, yes this is the channel for great informative videos, especially if you are an amateur mechanic, thanks for supporting my channel and yes I will continue producing these videos for all to benefit from.

Keep it coming Gary. These bigger jobs are what the viewers want. Nice!!

@vehiclemaintenanceandrepai3790

3 жыл бұрын

Thanks for your support once again, I will keep it coming.

Very amazing am from Zambia from your work have learnt a lot more on VW

@vehiclemaintenanceandrepai3790

5 ай бұрын

Thank You for supporting my channel with your visit and interaction, please feel free to check out the rest of the channel by clicking PLAYLISTS www.youtube.com/@vehiclemaintenanceandrepai3790/playlists for more helpful service and repair videos on most makes of cars available here in SOUTH AFRICA.

Thank you for the great video! The car is running so smooth.

Thanks alot brother ❤

Thank you so much Gary, insightful.

@vehiclemaintenanceandrepai3790

2 жыл бұрын

Thanks for your support Papa Mollo, I am glad you found the video useful.

Awesome brother I'm busy building the same motor,I remove and install it by watching this video

@vehiclemaintenanceandrepai3790

2 ай бұрын

Thank You for supporting my channel with your visit and interaction, I am pleased this video was helpful to you. Please feel free to check out the rest of my channel by clicking PLAYLISTS www.youtube.com/@vehiclemaintenanceandrepai3790/playlists for more helpful service and repair videos on most makes of cars available here in SOUTH AFRICA, It is FREE.

I'm not even a mechanic but I love your videos

@vehiclemaintenanceandrepai3790

3 жыл бұрын

Thank you for your support, Radi much appreciated.

Thanks Gary, appreciate your video's, keepit going

@vehiclemaintenanceandrepai3790

Жыл бұрын

Thanks for your support Koos, without viewers and subscribers the videos would not be possible.

You are good..keep it UP.

Thank you for the video

You are the Master of Clp/Cls Engine👏👏👏👏

@vehiclemaintenanceandrepai3790

Жыл бұрын

I try Brian, thanks for supporting my channel with your visit and interaction, love it!!

nice and understandable video

@vehiclemaintenanceandrepai3790

5 күн бұрын

Thank You for supporting my channel with your visit and interaction, I am pleased this video was helpful to you. Please feel free to check out the rest of my channel by clicking PLAYLISTS www.youtube.com/@vehiclemaintenanceandrepai3790/playlists for more helpful service and repair videos on most makes of cars available here in SOUTH AFRICA, It is FREE.

Awesome video. Loved the detail and clear communication. Well done.

@vehiclemaintenanceandrepai3790

Жыл бұрын

Thanks for your support it is well appreciated.

He is very good & what I like about his he makes sho that you understand & you olso learning. Than you very much boss keep it up

@vehiclemaintenanceandrepai3790

2 ай бұрын

Thank You for supporting my channel with your visit and interaction, I am pleased this video was helpful to you. Please feel free to check out the rest of my channel by clicking PLAYLISTS www.youtube.com/@vehiclemaintenanceandrepai3790/playlists for more helpful service and repair videos on most makes of cars available here in SOUTH AFRICA, It is FREE.

salute Gary

@vehiclemaintenanceandrepai3790

Ай бұрын

Thank You for supporting my channel with your visit and interaction, I am pleased this video was helpful to you. Please feel free to check out the rest of my channel by clicking PLAYLISTS www.youtube.com/@vehiclemaintenanceandrepai3790/playlists for more helpful service and repair videos on most makes of cars available here in SOUTH AFRICA, It is FREE.

Thanks for new info am also driving a polo clp engine

@vehiclemaintenanceandrepai3790

8 ай бұрын

A great pleasure, thank you for supporting my channel with your visit.

Thank you for the information

@vehiclemaintenanceandrepai3790

Жыл бұрын

I'm am glad you found value in it, thanks for your sup[port

baie netjiese video meneer baie dankie

@vehiclemaintenanceandrepai3790

2 жыл бұрын

N' groot plesier, dankie vir die ondersteuning Nick

Hallo Garry, dankie vir die nuttige video's, ek leer baie op hierdie manier. groete uit Nederland.

@vehiclemaintenanceandrepai3790

5 ай бұрын

Dankie vir U ondersteuning, Thomas ek vaardeur dit baaie, Thank You for supporting my channel with your visit and interaction Thomas, I am pleased this video was helpful to you. Please feel free to check out the rest of my channel by clicking PLAYLISTS www.youtube.com/@vehiclemaintenanceandrepai3790/playlists for more helpful service and repair videos on most makes of cars available here in SOUTH AFRICA, It is FREE.

As ever, most interesting.

@vehiclemaintenanceandrepai3790

3 жыл бұрын

Thanks, man, I am glad you like it.

I am in Cape Town Southern Suburbs

Best torturial video ever, keep up the good work

@vehiclemaintenanceandrepai3790

Жыл бұрын

Thank you for your support and encouragement.

Dankie Garry vir ń lekker video.....gee ń lekker Cruz in die other videos.....love the knowledge you always sharing

@vehiclemaintenanceandrepai3790

3 жыл бұрын

Creating a legacy of sharing is fulfilling and satisfying, Sathasivan.

@sathasivanmurugas8639

3 жыл бұрын

@@vehiclemaintenanceandrepai3790 Much appreciated Garry. Have a blessed one

@vehiclemaintenanceandrepai3790

3 жыл бұрын

Thanks, Sathasivan, all the best to you too.

Sir thank you for your time. I no apreaday how the repiar this polo alreaday thank very much

Top mechanic salute🫡

@vehiclemaintenanceandrepai3790

Ай бұрын

Thank You for supporting my channel with your visit and interaction, I am pleased this video was helpful to you. Please feel free to check out the rest of my channel by clicking PLAYLISTS www.youtube.com/@vehiclemaintenanceandrepai3790/playlists for more helpful service and repair videos on most makes of cars available here in SOUTH AFRICA, It is FREE.

you are the best

@vehiclemaintenanceandrepai3790

Жыл бұрын

Thank you Theko, your continued support is greatly appreciated. Gary.

Brilliant video. Keep them coming

@vehiclemaintenanceandrepai3790

4 ай бұрын

Thank You for supporting my channel with your visit and interaction, I am pleased this video was helpful to you. Please feel free to check out the rest of my channel by clicking PLAYLISTS www.youtube.com/@vehiclemaintenanceandrepai3790/playlists for more helpful service and repair videos on most makes of cars available here in SOUTH AFRICA, It is FREE.

Thank you..what is the torque settings for cylinder head bolts

I so wish u can fix my car, I have the problem similar to this one it's a CLP polo

What could be the cause of my polo vivo 1.4 16v. The water still went to the sump after putting on a new head gasket

Good job so far,but can you get one where you strip and reassemble the same engine

@vehiclemaintenanceandrepai3790

2 ай бұрын

Thank You for supporting my channel with your visit and interaction, I am pleased this video was helpful to you. Please feel free to check out the rest of my channel by clicking PLAYLISTS www.youtube.com/@vehiclemaintenanceandrepai3790/playlists for more helpful service and repair videos on most makes of cars available here in SOUTH AFRICA, It is FREE.

nice

@vehiclemaintenanceandrepai3790

5 ай бұрын

Thank You for supporting my channel with your visit and interaction, please feel free to check out the rest of the channel by clicking PLAYLISTS www.youtube.com/@vehiclemaintenanceandrepai3790/playlists for more helpful service and repair videos on most makes of cars available here in SOUTH AFRICA.

Good evening Gary, I overall a clp motor 1.6 but my vehicle overheat. If I connect the fan directly it runs perfectly well. Can you please advice

Hi Gary, I hope you are good sir, thank you for these wonderful videos they really do help. I was working on the exact same engine but it was leaking oil on the timing cover seal, i removed the timing cover as per instructions on the video and then replaced gasket and the seal that was leaking, then i put it all back together, as per the assemble video, but now the car wont start, all it does it cranks, would you be so kind to advise what could be causing this ? I did not touch/mess with the timing chain, all i did was just remove the cover to replace the seal and gasket, then assembled.

@vehiclemaintenanceandrepai3790

Жыл бұрын

Cam and crank sensors check if they are connected and in good working condition.

When the rockers kept falling off, I was so waiting for the swearing.

Hi Gary, where did you get the timing kit from for this car?

What are the torque settings for the flywheel and main bearings as well as big end bearings?

The rockers clip onto the lifters so that they don't fall off when fitting the cam box

@vehiclemaintenanceandrepai3790

11 ай бұрын

Yes they do but it is not fool proof, one still has to take care when fitting.

Very good. Xplain

@vehiclemaintenanceandrepai3790

2 ай бұрын

Thank You for supporting my channel with your visit and interaction, I am pleased this video was helpful to you. Please feel free to check out the rest of my channel by clicking PLAYLISTS www.youtube.com/@vehiclemaintenanceandrepai3790/playlists for more helpful service and repair videos on most makes of cars available here in SOUTH AFRICA, It is FREE.

The suspense has been killing me

@vehiclemaintenanceandrepai3790

3 жыл бұрын

Thanks for supporting my channel Nzwakele

@Kingwara_SA

Жыл бұрын

Those rumble n 1gugqu,

Happy i found this channel...was that a new chain??

@vehiclemaintenanceandrepai3790

3 жыл бұрын

Glad you did Gary, yes it was. Feel free to browse through the 150+ videos on my channel, it is free.

I have replaced my old clp engine with another second hand clp engine but the car doesn't start even though it cranks. What can be a problem?

Any videos on the sum removal on this vehicle. Do we need to remove any gearbox bolts to remove the sump cover

@vehiclemaintenanceandrepai3790

Жыл бұрын

It should be straight forward, but the exhaust runs from the front of the car under the sump.

Hi Gary, i did some work on the same engine and followed what you are doing however when i crank the car the intake takes air out rather the in. Any advice mind you i did a complete engine overhaul by changing crankshaft pistons and camshafts

@vehiclemaintenanceandrepai3790

Жыл бұрын

There are 4 strokes an engine goes through when being cranked it seems your exhaust stroke (air out) is working, but your air is not (intake stroke), either the compression rings are broken or the valves are not sealing on that cylinder, the cam timing could also be incorrect, (timing chain set wrong)

Those rockers popping off wont some sticky wynns engine lube hold them abit? While installing.

@vehiclemaintenanceandrepai3790

10 ай бұрын

If anything can help, use it just be sure they are all in their correct place when tightening down the cam.

Hi I have a polo 03 1.4 16v bby there are no spark on the coil packs can you please help

You need to put some engine oil on bolts treads....

Hi there I have a golf 3, 1998 model, 1600 My vacuum pipes going into the firewall must be replaced. What would be the best option ?

@vehiclemaintenanceandrepai3790

2 жыл бұрын

Vacuum pipes going through the firewall ???, never seen that yet Franco, don't you mean the heater pipes.

Hi Gary, I have an engine similar to this (in fact, identical), it runs perfectly fine and picks up speed pretty quick. However, when I was doing a service last week, I noticed that the spark plugs and coils were wet with oil. I had to them come watch this video and now the only thing that makes sense is that the o-rings around the spark plug tubes are worn. Any ideas how I can go about replacing them without tempering with the timing belt? Timing seems to be a delicate job so I'm not confident enough to tackle it.

@vehiclemaintenanceandrepai3790

2 жыл бұрын

Unfortunately, Yanda-Lo, you have to remove the cam box to access those seals, sorry man. Gary

@yanda-lo7859

2 жыл бұрын

@@vehiclemaintenanceandrepai3790 I understand, thanks for the reply

Hi Gary I need your advice a have a polo that runs with bah 1.6 n now I want to put a polo 6 motor on it which is also a 1.6 so is it possible to run that motor with this engine?

@vehiclemaintenanceandrepai3790

Жыл бұрын

What motor are you referring to, I do not understand your statement oscar

Like your video. Where are situated.

@vehiclemaintenanceandrepai3790

4 ай бұрын

Cape Town Thank You for supporting my channel with your visit and interaction, I am pleased this video was helpful to you. Please feel free to check out the rest of my channel by clicking PLAYLISTS www.youtube.com/@vehiclemaintenanceandrepai3790/playlists for more helpful service and repair videos on most makes of cars available here in SOUTH AFRICA, It is FREE.

Where are you located? I think my polo 6 has the same problem you fixed

Good day Gary My Polo 1.6 CLS engine is refusing to start and idle. What l notices is that it has burnt all the oil. But my problem is getting starting to take it to the dealer or the mechanic. Please advise.

@vehiclemaintenanceandrepai3790

Жыл бұрын

It seems you have a compression problem Mackenzie, maybe broken rings, best to do a compression test to make sure.

My Clp 1.4 engine keeps loosing timing any ideas what could be causing it. Maybe you are familiar with this problem the valves keep bending when that happens

@vehiclemaintenanceandrepai3790

2 жыл бұрын

Hi Prince Dube, thanks for supporting my channel with your visit and your interaction, it really does help to grow the channel and is appreciated tremendously. It sounds like you have stretched chains causing it to jump a tooth or two causing bent valves, when you do the chains do the sprockets, guides, and tensioner at the same time, hope this helps.

@yonelazulu402

2 жыл бұрын

Hi Gary i have a similar problem i bought a new tensioner but my car keeps loosing timing

My polo clp 1.4 engine compression is 125psi on all cylinders is that fine?

@vehiclemaintenanceandrepai3790

Ай бұрын

Yes, that is a good compression. Thank You for supporting my channel with your visit and interaction, I am pleased this video was helpful to you. Please feel free to check out the rest of my channel by clicking PLAYLISTS www.youtube.com/@vehiclemaintenanceandrepai3790/playlists for more helpful service and repair videos on most makes of cars available here in SOUTH AFRICA, It is FREE.

When are you going to do a 1.4 CLP...no videos on KZread about the CLP motor

@vehiclemaintenanceandrepai3790

Жыл бұрын

When one comes in for that procedure it will be filmed, thanks, Chadwick.

Cual motor es este? 1.4 ,1.6. 1.8 diésel???

Gary just one Question ...im planning on buying a polo 9n3 gti engine with it's gearbox but wana put it in a golf1 body...so how much will u charge me to do that convertion...

@vehiclemaintenanceandrepai3790

Жыл бұрын

Sorry Abdoel, it is not a project I would tackle.

@abdoelmeyer9105

Жыл бұрын

not a problem

Hi Gary, I'm the timing on the similar engine, I do the timing tool kit and I used it accordingly, but the moment I turn the ignition it bends the the valves, inlet valves, what could be the cause of that, please help me I've taken the head off for three times now

@soluledepa4702

2 жыл бұрын

Bra I have the same problem with my Polo 😭

@yonelazulu402

2 жыл бұрын

🤦‍♂️

@bayandabuthelezi5805

Жыл бұрын

iwas having the same problem only to find that it a crank pulley that connect chain the groove that connect crank it damage so when it running it lost timing then bend valves

Good day Gary im a DYI guy not a pro like you. Your video was really inciteful. However, I have a 1998 skoda fabia 1.4 16v. The engine is almost identical in make minus the timing chain. I recently changed my head gasket. I have two concerns timing and knowing what stroke im on. How do i determine this?

@vehiclemaintenanceandrepai3790

Жыл бұрын

Hello Trevor, when timing an engine, the No.1 piston must be TDC, all the way up, and the cylinder head's valves should be rocking on the No.4 cylinder to ensure the valves on the No.1 cylinder are all closed. By rocking I mean the precise point where the inlet valves close and the exhaust valves open, mostly the head will have markings on the timing gear to indicate this point, but an experienced mechanic should know how to set this up, I hope this answers your question, thanks for supporting my channel it is well appreciated. GARY

@trevorbethell8695

11 ай бұрын

Gary I have another question. If I set up as said and it still doesn't want to start what do you suggest? I have new spark plugs, confirmed that the fuel pump is working, it sounds like it wants to start but it doesn't. Appreciate your advice sir

@vehiclemaintenanceandrepai3790

11 ай бұрын

There are so many factors affecting the timing of the engine, but in your case, do a compression test to see if the compression is adequate.

@trevorbethell8695

9 ай бұрын

Good day Gary when you are changing the belt on the camshaft. There's a position that you can positon the cam to where you can lock it with two pins. Is the cam then in a position as you mentioned earlier where piston 1 is TDC and piston 4 rocking?

@vehiclemaintenanceandrepai3790

9 ай бұрын

Yes

Hi Gary, If I may ask where can I buy the kit from?

@vehiclemaintenanceandrepai3790

2 жыл бұрын

Masterparts and Alert engine spares, google for nearest branch. Oscar

is it 1.4 BBY engine?

@vehiclemaintenanceandrepai3790

Жыл бұрын

CLS engine.

Wha is the spec for cylinder head mazda 323 b3 engine please Mr.

@vehiclemaintenanceandrepai3790

Жыл бұрын

Head bolts torque setting (cold) 76/81nm, mains 54/59nm, big ends 29/34nm, hope this helps Thapelo, thanks for supporting my channel with your visit.

Hi where can I get hold of this guy

@vehiclemaintenanceandrepai3790

Жыл бұрын

Try 0714046332 WhatsApp

How much was this job same car engine cls 1.6?

@vehiclemaintenanceandrepai3790

Жыл бұрын

This cost 12k at the time.

Hi Gary..where are you based?

@vehiclemaintenanceandrepai3790

Жыл бұрын

Cape Town, South Africa

Hi Gary my issue is when I try to unlock the crank pulley bolt to place the timing cover..I seem to slip back the tensioner when ùnlocking crank bolt,any advice how to remove the bolt without pushing the tensioner?

@vehiclemaintenanceandrepai3790

Жыл бұрын

You need special tools such as what I am using timeline 38:42, or the job will not be very successful, Thando

Hello uncle garu What is the opening sequence for the cylinder head. Thanks

@vehiclemaintenanceandrepai3790

5 ай бұрын

Sorry I do not understand the question completely, if you mean removing, then it does not matter which bolts are loosened 1st, as the head will be sent to the engineers for skimming

@MaxyRepairs

5 ай бұрын

Thank .that what actually wanted to know

@vehiclemaintenanceandrepai3790

5 ай бұрын

@@MaxyRepairs Thank You for supporting my channel with your visit and interaction, I am pleased this video was helpful to you. Please feel free to check out the rest of my channel by clicking PLAYLISTS www.youtube.com/@vehiclemaintenanceandrepai3790/playlists for more helpful service and repair videos on most makes of cars available here in SOUTH AFRICA, It is FREE.

@MaxyRepairs

5 ай бұрын

Greetings I'm a very big fan off your channel Thanks to lord and your videos with all dat info I have done my 1st engine overhaul And have succeded in it. Thank you my lord bless u abundantly. I wil pray u.keep doing mor good just as u have till dis moment Not many machenical share der knowledge As u have. Thank you My name mohammed kazi

@vehiclemaintenanceandrepai3790

5 ай бұрын

Great Mohammed, I love the fact that you are doing it and learning more, I love to help those that helps themselves, I wish you great blessings and success for 2024.👍👍

Mr gary where are u based

@vehiclemaintenanceandrepai3790

Жыл бұрын

Cape Town

Where you from sir.. do you work from home

@vehiclemaintenanceandrepai3790

10 ай бұрын

Cape Town, Yes

That's not how a torque wrench should be used