Cam Follower Kit: goo.gl/Lx7m1N Schwaben Stubby Socket Set: goo.gl/rgR3n2 Additional Tools Used: goo.gl/uddfri Upgraded High-Pressure Fuel Pumps: goo.gl/x8ntLs FSI Intake Removal DIY: kzread.info/dash/bejne/lZqVt6WBqbvAldo.html

@kyriewaylon823

2 жыл бұрын

instaBlaster

I love watching Zach work on 8P A3’s knowing he’s in Donut Media now

@Assasination143

4 жыл бұрын

this confused me thought i was going mad till seeing this comment XD

@ie_b8_a453

4 жыл бұрын

dude im removing my HPFP on my audi right now so i pulled up this bideo and got the same shock you did!

@Svendrys

Жыл бұрын

I knew I saw him before :D

Please do more diy’s on that car, preferably every major job lol

@RatchetWrenches

6 жыл бұрын

Authorized Mike check us out we have a Ton of content for that same motor, just waiting to release

HEY! It's that Donut guy :)

Just bought one. I'm a noob when it comes to euro cars and turbo cars. Just bought a MK5 GTI, and looking for preventative cheap fixes. The video was great thanx!

I have a banjo bolt on mine and this is the first time working on the HPFP. This video was absolutely invaluable!!! Also always love watching Zach Jobe working on cars lol.

Thanks a bunch! I recently bought a 2007 gli Fahrenheit edition. Did my research and found out this needs to be part of my routine maintenance. It was super easy to change only took me about 30 minutes!

@noventay4

Жыл бұрын

The important question was did it needed to be replaced?

Love these videos! Would love an entire series on 2.0T CAEB engine

Thank you! Just finished changing mine (2008 audi tt 2.0fsi). It was warn a bit but not as much as I expected. You guys made the job easy amd I appreciate that. I had hose instead of a banjo bolt, that was the most annoying part.

That damn banjo bolt! I broke the brittle plastic lower PCv hose trying to get to that and lost my m8 bit on because it didn't have that fancy retainer thing as this one does spent an hour fishing that out but can complain about the hose I replaced it with a real rubber hose. Gave up on the follower that day but I'm going to try again with a better approach thanks for the video

Man thanks a lot for doing the benjo bolt variant. I followed your instructions and had no issues with the repair. When I was putting everything back together, however, a hose connector nipple broke off from the coolant flange right next to the hpp because apparently it as heavily corroded. I had to do an emergency repair in that I drilled an 8mm hole where the said nipple used to sit and replaced it with a brass tube that I squeezed into a thick silicone hose and sealed the shit off, hopefully for good, with some vinyl tape. That way a quick repair turned into a few hours of tinkering... phew

Nice and easy to follow video with clear instructions. I'm going to do this for my wife's Audi TT as a precaution. Thank you for the video. Liked and Subscribed. 👍🏻

Oh hey! That's my 06 silver A3! Even has the black border on the front grill 😁 Thanks for this tutorial! Been wanting to replace my cam follower but it seems difficult, but knowing which tools I need I can feel confident doing it now!

Great video, nicely done, well explained, makes me confident to try the cam change myself 👍

just bought an 06 a3 with 100k on it.. ill be doing this asap. amazing diy! thank you

No mess, no fuss, nice !

Great writeup. I just ordered my kit from you and will get this done when it gets here.

Terrific video, thanks very much for sharing. Wondering if this might resolve the rough idle issue on my 2007 GTI

Am almost mid way through the video and maaaan what a performance.. am talking like stage 2 kit in your hands man.

Is it only the turbo engines, that have these, do the n/a engine’s have something different?

Looks like an easy job

Merci pour le tuto !

Is this also for 2.0 engine? Is have mk5 gti farenheit edition and i turned it on and it died and didnt want to start , finally started but still idk if this could be the problem

I’m glade you guys posted this video! What about the timing belt kit with the water pump? Do you guys have a video uploaded on that?

@RatchetWrenches

6 жыл бұрын

Rafael Espinoza soon I’ll be uploading my timing belt video. Super easy to follow

If the camshaft happens to be in a position that it's hard to screw the pump back on, is it possible to turn the camshaft by hand so it's in a more convenient position?

is the cam follower same for all AXX/BWA/BPY engines ?

Hello, What was the problem or error kod that you shoud replace it? Thanks.

What oil and grease did u apply on that new cam follower u put in there?

Wow brilliant I’m being told my gfs car needs this done what problems does this cause? Thanks

@jimtonkin713

4 жыл бұрын

I own a VW Passat with the same engine. The problem is the end of the intake cam which runs the fuel pump wears out and doesn’t deliver the adequate amount of fuel for the car. Yeah replacing the follower helps, but if the end of the cam is messed then the car won’t be injecting fuel properly and will put the car into a sort of limp mode because the ECU recognizes the car isn’t getting fuelled properly. 91 octane (which this engine must run) acts as a sort of cooling agent so if the car can’t be cooled properly then it’ll just destroy itself.

For Touran 2.0 FSI 2005 j ist the same or not ?

I have a 2008 Volkswagen Jetta 2.0T fsi turbo. It wouldn’t start so I replaced the high pressure fuel pump and the in tank fuel pump. I eventually got it to start. It starts right up and idles fine, but when you give it gas it’s all choppy and not the correct rpm it should be at. I have a engine code, it’s P2294, so that means that there’s a problem with my fuel pressure regulator attached to my high pressure fuel pump, but the regulator is brand new so I don’t know what to do

Can’t seem to get the electric housing to come off the side of the pump. Any ideas?

Do I need to rotate my camshaft when installing my new fuel pressure pump? I seen another video and the guy said that you must rotate the camshaft to the flat side? Lmk thank you

Hello, ist the same Motor VW Touran 2.0 FSI ,Motor Code BLX or Not ?

Is it possible the cam follower comes with a roller/bearing?

Didn't realize the HPFP cam follower is a regular maintenance item on DI cars. Just ordered a new one for my mazdaspeed3. Hopefully solves my fuel pressure issue

Oh, look at that, the Donut Media guy with the hairdresser car :))

BANJO bolt needed to be replaced ?

This video does help and could help you fix your FSI engine. The problem is if the end of your intake camshaft is already worn down then replacing the follower will only prevent the fuel pump from getting damaged even more. I’ll try and sum this up the best way I can explain as I own a VW Passat with the same engine. The problem is the end of the intake cam which runs the fuel pump wears out and doesn’t deliver the adequate amount of fuel for the car. Yeah replacing the follower helps, but if the end of the cam is messed then the car won’t be injecting fuel properly and will put the car into a sort of limp mode because the ECU recognizes the car isn’t getting fuelled properly. 91 octane (which this engine must run) acts as a sort of cooling agent so if the car can’t be cooled properly then it’ll just destroy itself. The end of my cam is messed up as the previous owner of my car never had the cam itself fixed and only had the fuel pump and follower fixed. I’m not really an expert on Euro cars but I know a mechanic who previously worked at a VW dealership who dealt with these FSI engines all the time when they first started to have this problem.

@JohnSmith-hv3mj

Жыл бұрын

Late to the party but I had my hfpf and camshaft replaced for this exact reason at about 130k miles lol, about to replace the cam follower 30k miles later, i know, i'm late. I wish I had known about the ECS conversion kit that eliminates the problem entirely, although it's $650. I just passed 160k miles on my 2008 B6 tfsi

@jimtonkin713

Жыл бұрын

@@JohnSmith-hv3mj I know the kit your talking about. In Canada that kit cost well more than what my car was worth and cause I was 17 and didn’t know any better I bought everything separately on two websites. One site was Canadian and I only bought a gasket and the special socket for the one weird cam bolt. The other one I bought the cam follower and whole camshaft assembly off of and at the time I didn’t realize the site was American and just those two parts alone exceeded the value of my car without me realizing so it was a rude awakening when I checked my bank account later. I did end up replacing everything and about 3 months later the car started burning more oil than it did gas and the electronic parking brake would turn on for no reason so it was new car time after that. Ended up with a brand new Corolla hatchback that uses the same direct injection system lol.

Thanks 👍🏻

Hey, man, I got a problem with my car. my vehicle is an Octavia with a 1.6 FSI engine. I drive down the road in my car and he cuts off the gas. the gas needle surges and the engine stops. the computer shows error code p2293. Service officials say the problem was caused by a high pressure pump. however, since the problem is not always experienced, I think there may be a problem with some other equipment. I care about your ideas, and I await your answer.

Y para cambiar el cam follower de un audi a4 2.0 2006 como lo arias

is the cam lobe always there or do you need to mess with timing ?

@freakyfrank1549

2 жыл бұрын

If your vehicle is lacking a cam lobe you have a much bigger issue smh

Tackling my cam follower tomorrow along with the cracked valve cover causing leaks and the exhaust because it’s to low and scrapes everything

Is this only on the S3? A3 not effected?

How many miles was on the old one?

Nice job doing it on a car with a banjo bolt. I don't think any other diy video shows that.

ZACH JOBE!!!!

I just finish my install very easy, however, one issue i had was removing the top plug connector to the top of the high pressure pump. I even used WD40 to slowly remove the top connection and the bloody thing cracked. I looked at the original cam follower had some wear nothing major. Would anyone know by having a crack on the top switch im going to have issues. After installation i turned the motor on and left it for 5min, No engine light.

Awesome job

Great video. Just bought a Scirroco 2.0 tsi 2012 with 50k miles. Going for a stage 1 remap. Is 250 bhp and 290 ft/lb torque safe on the engine ? Appreciate your input. Thanks

@ecstuning

5 жыл бұрын

A basic off the shelf stage 1 tune is considered pretty safe, although any tune putting out more power increases the stress on an engine. With the Gen 1 TSI, you don't have to worry about upgraded internals until you get into bigger turbos (beyond a K04.) Congrats on the Scirroco, wish we had those in the US!

@paull123

5 жыл бұрын

@@ecstuning Thanks for taking the time to reply. Much appreciated !!

swear seen this guy on another youtube channel and a big ish one

Cause that Start Problems without any engine light? 2.0 tsi passat cc

GOD....I bought a 06 VW 2.0T FSI off someone in my town. And it wouldn't turn over the day before yesterday. This would explain alot

Shouldn’t you replace the banjo bolt also .?

What is the lube you put on the end of the cam follower?

@bankpin

4 жыл бұрын

Pre instail lube

Ok I have seen so many of these diys but mine DOES NOT HAVE THE PRESSURE VALVE just what looks like a hard like with a banjo bolt

I just completed this job on my 08 A3. The follower was extremely worn and the cam lobe has a good deal of wear. What should I do about the lobe if anything? Since it's worn and uneven I imagine I'll have to change the follower more often. Everything else is working.

@ecstuning

6 жыл бұрын

Welp, unfortunately, the original camshafts were way too soft. If your lobe shows signs of wear, you'll eat cam followers left and right. There is a revised camshaft that is properly hardened and will solve your issues. Replace the camshaft, re-replace the follower, and do an oil change to get any metal debris outta there, and you'll be set. Here's the cam: goo.gl/A66WzT

@noelaguirre7104

5 жыл бұрын

How many miles did you have on your Audi when the cam follower was replaced?

I like Jobe

Hi guys, is this the same for a BWA Audi TT 8J 2.0TFSi?

@bankpin

4 жыл бұрын

Mines bwa 8pa and it is yes

Does the 2010-2012 2.0 tsi CDLA engine (found in golf 6 R/Audi s3) have the same problematic cam follower?

@jelizond1010

4 жыл бұрын

No, the TSI does not have this problem.

@DmitryAvsioukov

2 жыл бұрын

Yes, it does.

@DmitryAvsioukov

2 жыл бұрын

@@jelizond1010 wrong

This makes me want a money pit mkv GTI

Cómo saber cuando necesita reemplazo?

@jaimeanton9686

4 жыл бұрын

lo recomendable es cada 20-30.000 kms

Does this need to be done to TSI?

@ecstuning

5 жыл бұрын

Nope, they got it right on the TSI!

Hey ECS (and those watching), do you (anyone) know if 2006-2008 Polo Gti with the older 1.8L Golf Gti engine suffer the same problem? Cheers

@eponymous7910

10 ай бұрын

No. That 1.8T engine is bulletproof. Service it on time and it'll go forever 🤟

As shown on other videos, the best way to initially reduce the pressure without directly releasing too much fuel is to run the car with the fuel pump system lead disconnected for about 10-15 seconds. This will make it low pressure.....

My torque wrench is 20 to 150 pounds so how do I make sure its at 7and half pounds now?

@DmitryAvsioukov

2 жыл бұрын

Buy appropriate one, huh?

No crank no start… new cam sensor battery plugs and coils soo could it be this or starter or… ?

My HPFP does not have a schrader valve, how do i release the pressure?

Ecs please respond I need your advice.. What is a good audi to buy and modify under 15k???

@ecstuning

6 жыл бұрын

Hey Omar, what are your goals for the car? Is it going to be a daily driver, a weekend track car?

@bullyzelda5981

6 жыл бұрын

ECS Tuning I'm looking for a daily driver that can be really quick

@ecstuning

6 жыл бұрын

If you can stretch the budget slightly, a used B8 S4 is one of the best "bang for the buck" Audi's there is. The supercharged V6 sounds amazing and puts down some great power with a simple tune, intake, exhaust, and pulley. Otherwise, maybe look at a used 8V A3 2.0T or a B8.5 A4 (make sure the A4 has the updated timing chain tensioner.) They can both be pretty quick with the right modifications (intake, downpipe, tune, turbo upgrade.)

Does 1.6 FSI engines has this problem?

@yersiniapestis9137

3 жыл бұрын

yes, its the same part that fails

@m4re94

3 жыл бұрын

@@yersiniapestis9137 what are sympthoms and sighns of bad cam follower?

does 1.6 FSI also have Cam follower?

@yersiniapestis9137

3 жыл бұрын

yes

@yersiniapestis9137

3 жыл бұрын

Its not placed the same place as a2.0T but more in the middle

Does the B8 have the revised camshaft?

@EJR20

3 жыл бұрын

@aferran69 like it comes stock with it? And so we don’t have to worry about it?

@EJR20

3 жыл бұрын

@aferran69 I keep seeing your comment about only the b7s having the cam follower on my notifications but not here; I guess you got rid of it once you found out that they do, but anyway what kind of preventive maintenance are we talking here?

hello what is the tab you put on top of the cam follower? thank you. friendships of france

@EastOnyx

4 жыл бұрын

Do you mean the red assembly lube?

@martymacfly4002

4 жыл бұрын

@@EastOnyx Yes thanks

What's weird is my HPFP doesn't have a schrieder valve on it

@MiniBandit007

5 жыл бұрын

Then someone has been there before and lost the valve, does it just have a normal bolt in the hole?

@svecmobiii

5 жыл бұрын

I too am missing the Schrieder valve. Its just blank. how do I bleed out the pressure?

@MiniBandit007

5 жыл бұрын

@@svecmobiii you will have to very carefully loosen the bolt or whatever is there, if that isn't an option just have a lot of rags nearby and surrounding the fuel line when you undo it, and some safety glasses and gloves

@svecmobiii

5 жыл бұрын

Thank you

@erictech201

4 жыл бұрын

Matt Svec you just need to unplug the fuel pump the sensor on top unplug it then start the car let running for a few 5 minutes let the fuel pressure go down that should do the trick

Omg it’s the guy from DONUT!!!!

what is up with your shipping.. estimated ship date november 27th???

@imaugiie117

9 ай бұрын

I ordered mine last Wednesday and got it today

@JaseCJay

9 ай бұрын

@@imaugiie117 good for you.. that's not what was indicated on their website for me!

@imaugiie117

9 ай бұрын

@@JaseCJay it never told me it was getting shipped it just kept saying my package was ready to be shipped witch was weird just letting you kno

@JaseCJay

9 ай бұрын

@@imaugiie117 domestic tracking can leave something to be desired sometimes! Get something outta Shenzhen and there's 23 updates by day 2 ffs

is it normal to be that gunky on that corner?

should have scraped clean the mating faces & cross torqued those fasteners champ.

30-40k miles lol yeaaaah right. My 07 GTI would just about eat thru a cam follower about every 3 oil changes .... U wait 30-40k and I'll need a few new parts

Pain in the arse to reach the banjo bolt on the A4 with the longitudinal arrangement. Good grief.

@eckopoppin

5 жыл бұрын

DEVLAD yeah what the fuck man....I can’t get the banjo bolt out...almost seems like I can’t get the m8 to sit properly so I can’t get t out without risk of stripping it...any advice?

@erictech201

4 жыл бұрын

eckopoppin there’s a special tool that is specific for that spot it’s a extra long m8 that reaches that bolt

Could have shown it on a longitudinal engine

Ya forgot to mention that the fittings on the high pressure fuel pump are softer than joe biden and need to be replaced as well with this project :P

@donut tbt