Veise Fingerprint Digital Deadbolt Door Lock - Installation and Setup
Awesome and Easy!! Stores 20 prints! Uses fingerprints or codes. Features: one- time code, vacation mode, etc.
Жүктеу.....
Пікірлер: 27
@ticktock2930Ай бұрын
Very helpful, well done.
@Jean78578
Ай бұрын
Thanks. I'm glad it was helpful!
@peterchen9523 ай бұрын
Thank You. It's so clear and easy from your instructions.
@Jean78578
3 ай бұрын
Glad it was helpful!
@Glock103572 ай бұрын
Thank you so much for the video I installed everything right the thing that I didn’t do was do the reset with the little key to get where the deadbolt would turn. Thank you so much for your video.
@Jean78578
2 ай бұрын
Glad I could help!
@Nightsight9712 ай бұрын
Omgsh, thank you your video made it so easy!!!!
@Jean78578
2 ай бұрын
You're welcome!
@fattypat2 күн бұрын
thank you
@Jean78578
2 күн бұрын
Welcome!
@4u25out4 күн бұрын
How is the battery life? I heard keyless entry with “finger print scanners” drains battery .TIA.
@Jean78578
4 күн бұрын
The batteries seem good. We've been on the same batteries from months.
@blueutpalaАй бұрын
Thanks for this! I was wondering if you could look the door from the outside without a key and apparently you can by pressing any number for two seconds. Totally missed this instruction, thank you!
@Jean78578
Ай бұрын
Yes you can! The door lock is pretty awesome..
@rachelyoungblood3168Ай бұрын
Do you happen to know how to delete all fingerprints off? Or reset it?
@Jean78578
Ай бұрын
You have to delete one fingerprint at a time. As follows: = = Master Code = 5 Scan fingerprint When successful, you will see the green light flash and hear a long beep. If the finger is not available, you may need to reset the lock to factory settings: Open the door and ensure it's unlocked. Press and hold the reset button (push a pen/pin into the tiny reset hole underneath the batteries) - while at the same time take out one battery, and then put the battery back in. Keep holding the reset button for about 3 seconds after putting the battery back in - until you hear a beep and see the latch automatically extend. See the video at about 1:24 for help. A factory reset will reset the master code back to 12345678, auto lock will be disabled, silent mode will be disabled, wrong code entry limit will be set to 10 times, shut down time will be set to 3 minutes, and vacation mode will be disabled. This is from my little user guide..
@wheelieboii10024 ай бұрын
My will not reset red light flashes
@Jean78578
4 ай бұрын
If you're seeing red flashing lights when trying to do any programming, ensure you're entering the master code correctly. The master code must be entered to make programming changes. It also flashes red a 4-5 times if you enter a personal code incorrectly. Also, when the batteries are low you will see a flashing red light.
@lindapeterson2399Ай бұрын
Help...mine is just showing red all the time
@Jean78578
Ай бұрын
It will show red whenever an invalid command is entered or an invalid master code..
@philpernice47222 ай бұрын
im not getting any green lights
@Jean78578
2 ай бұрын
To do any programming, you first have to enter the correct master code.
@philpernice4722
2 ай бұрын
@@Jean78578 i figured it out i didnt do the battery reset correctly once i did that i was able to get green lights the instructions are not the greatest
@Jean78578
2 ай бұрын
Fabulous!
@lindapeterson2399Ай бұрын
Should i unplug it and start all over
@Jean78578
Ай бұрын
Red light means whatever you have tried to set up has failed. Re-enter the master code and start fresh. Be sure to follow the exact sequence shown on the colored instruction sheet..
@lindapeterson2399
Ай бұрын
I tried that, even went as far as Unplugging the unit and started over. No good. UGH
Пікірлер: 27
Very helpful, well done.
@Jean78578
Ай бұрын
Thanks. I'm glad it was helpful!
Thank You. It's so clear and easy from your instructions.
@Jean78578
3 ай бұрын
Glad it was helpful!
Thank you so much for the video I installed everything right the thing that I didn’t do was do the reset with the little key to get where the deadbolt would turn. Thank you so much for your video.
@Jean78578
2 ай бұрын
Glad I could help!
Omgsh, thank you your video made it so easy!!!!
@Jean78578
2 ай бұрын
You're welcome!
thank you
@Jean78578
2 күн бұрын
Welcome!
How is the battery life? I heard keyless entry with “finger print scanners” drains battery .TIA.
@Jean78578
4 күн бұрын
The batteries seem good. We've been on the same batteries from months.
Thanks for this! I was wondering if you could look the door from the outside without a key and apparently you can by pressing any number for two seconds. Totally missed this instruction, thank you!
@Jean78578
Ай бұрын
Yes you can! The door lock is pretty awesome..
Do you happen to know how to delete all fingerprints off? Or reset it?
@Jean78578
Ай бұрын
You have to delete one fingerprint at a time. As follows: = = Master Code = 5 Scan fingerprint When successful, you will see the green light flash and hear a long beep. If the finger is not available, you may need to reset the lock to factory settings: Open the door and ensure it's unlocked. Press and hold the reset button (push a pen/pin into the tiny reset hole underneath the batteries) - while at the same time take out one battery, and then put the battery back in. Keep holding the reset button for about 3 seconds after putting the battery back in - until you hear a beep and see the latch automatically extend. See the video at about 1:24 for help. A factory reset will reset the master code back to 12345678, auto lock will be disabled, silent mode will be disabled, wrong code entry limit will be set to 10 times, shut down time will be set to 3 minutes, and vacation mode will be disabled. This is from my little user guide..
My will not reset red light flashes
@Jean78578
4 ай бұрын
If you're seeing red flashing lights when trying to do any programming, ensure you're entering the master code correctly. The master code must be entered to make programming changes. It also flashes red a 4-5 times if you enter a personal code incorrectly. Also, when the batteries are low you will see a flashing red light.
Help...mine is just showing red all the time
@Jean78578
Ай бұрын
It will show red whenever an invalid command is entered or an invalid master code..
im not getting any green lights
@Jean78578
2 ай бұрын
To do any programming, you first have to enter the correct master code.
@philpernice4722
2 ай бұрын
@@Jean78578 i figured it out i didnt do the battery reset correctly once i did that i was able to get green lights the instructions are not the greatest
@Jean78578
2 ай бұрын
Fabulous!
Should i unplug it and start all over
@Jean78578
Ай бұрын
Red light means whatever you have tried to set up has failed. Re-enter the master code and start fresh. Be sure to follow the exact sequence shown on the colored instruction sheet..
@lindapeterson2399
Ай бұрын
I tried that, even went as far as Unplugging the unit and started over. No good. UGH