You were 100% right about coating/oxidization on probes. I have that problem on meter leads and brand new two way radio batteries on charger contacts , they look fine but have an "invisible" coating on them. I did to these leads what I have done for years and years (I'm old) I rub them with a slight abrasive . I use Crest regular old fashion PASTE toothpaste , has a tiny bit of pumice in it . Put a small dab on thumb and forefinger and rub , then wipe off make a HUGE difference , continuity taste is immediate .

@MikeMakesIt

2 жыл бұрын

Hi cups3 thanks for the feed back. Good to know. I might try the toothpaste trick! Swapping the leads to gold plated ones could be another way to go though not as cheap. Thanks for watching 👍🏽

Received, indeed a little gem! Thxs for the review, very good!

@MikeMakesIt

Жыл бұрын

Hi , thanks for the feedback and of course for watching 👍🏽

just bought one. Thanks for the review .

@MikeMakesIt

Жыл бұрын

Hi Eric, thanks for the feedback. I don’t think you’ll be disappointed, it’s a great meter. Thanks for watching 👍🏽

Just a quick note, to let you know that electrolytic capacitors have a wide value tolerance usually +20% to - 10% of the marked value. It's usually marked on the side of the caps.

@MikeMakesIt

3 жыл бұрын

Hi Pidgeonplucker, thanks for your comments. Yes you're right I should have mentioned that when I was testing. Thanks for the reminder and for watching 👍🏽

The way you measuring Capacitors is not entirely correct. You are gripping both the probes, making your body a resistor in parallel over the capacitor. Better is to only grab the negative probe with one lead of the capacitor, and hold the positive only on the plastic, and hold the metal tip against the other leg of the capacitor.

@MikeMakesIt

4 жыл бұрын

Hi Victor and thanks for your comments. Yes you are entirely correct. I’ve just reviewed my video and I surprised myself I measured the caps that way! I shall be more careful next time. Thanks again, Mike.

Helpful review, Thanks

@MikeMakesIt

7 ай бұрын

Hi Marco, thanks for the feedback and for watching 👍

This exact meter was recommended by Mike over at Britannica Restoration. If you don't know about his channel it is worth a look as you said you owned a Land Rover. I was going to get this meter on Mike's recommendation and you have more than confirmed it.

@MikeMakesIt

3 жыл бұрын

Hi Harvey. I've been helped by a few of Mikes videos but not seen the one with the meter. As I said in my video I have found it very useful and it can been seen in use in one of the Defender "Step" videos. I think you will find the meter a great addition to your tool setup, thanks for watching 👍🏽

@whatworkedforme

Жыл бұрын

I had been looking for something like this for some time but prices put me off; esp for the infrequent use I expected to use it. I bought one of these immediately after seeing that video - primarily for the 2 amp DC ability.

One thing I can't get my head around .I used this to check amperage in my meter box at the safety switch .It showed I was drawing 2.5 amps on a circuit that I knows carries a lot of power points and appliances ,the dishwasher was on, one of my computers was on, the coffee machine was plugged in at idle, yet it showed 2.5 amps ?

@MikeMakesIt

Жыл бұрын

It could be right. The computer could draw 30-50watts (depends if it's a gaming machine or not) and the dishwasher could have just been pumping water around that had already been heated but before you started to measure. The coffee machine on idle would only have been a couple of watts. Stick an electric kettle on the same circuit and boil water. I'd expect to see another 2200watts (9amps ish on a 240v supply)

@ericnoack

Жыл бұрын

@@MikeMakesIt Ill try that cheers and thanks

Great video Mike. and no waffle or disco music overlaid.. LOL😀

@MikeMakesIt

Жыл бұрын

Hi Alan, thanks for the feedback and for watching. No music here!! 👍🏽

Someone may have posted earlier but I cleaned the probes with a pencil eraser and it 100% eliminated the lack of contact

@MikeMakesIt

2 жыл бұрын

Hi Joe, thats a great call! Thanks for watching👍🏽

Uni-t are a good brand They have made a big inprestion in the UK and Europe, all my test instruments are uni-t Exsept for my MFT with ia a ROBIN KTS 1620, I have a uni-t clamp meter a uni-t voltage indicator and a uni-t multy meter I have been using this brend for seven years and I have never had any problems with them, why pay hundreds of pounds /dollars for the likes of fluke mega kewtech and many others when you can get just as good for a fraction of the price from UNI-T

@MikeMakesIt

3 жыл бұрын

Hi Sean, thanks for your comments. I very much agree with you, I think the Uni-T brand is a very under estimated brand. The build quality is super and accuracy more than I need. If and when I need another meter I will certainly be looking at this brand. Thanks for watching 👍🏽

Does ut204+ can read 1 DC Amp ????

@MikeMakesIt

9 күн бұрын

The spec says it can read up to 600a DC but at what resolution at the lower end is unclear. Look here: amzn.to/3S5xXjw And here: meters.uni-trend.com/product/ut200plus-series/

@playstation2bigs

4 күн бұрын

​@@MikeMakesItDoes the red wire (positive) same DC current as black wire (negative) when using UT210E ?

@MikeMakesIt

2 күн бұрын

The cables are identical apart from the colour and will carry the same amount of current

👍

210E ok 210D no

@MikeMakesIt

2 жыл бұрын

Hi S8 hau. I guess it depends on what your particular measurement requirements are. The 210E was better for me this time. Thanks for watching 👍🏽