There is something about waking up on a Sunday morning with a cup of coffee and watching this genius of a guy work on metal.

@ildefonsogiron4034

3 жыл бұрын

It's better that, after a coup of coffee and this video, you finally find inspiration to start that project you've been delaying for some time. So, heading to the shop. Regards.

@myharris

3 жыл бұрын

'...watching this genius of a guy work on *anything*'. There, fixed it for ya! 😂

@mikepaul136

3 жыл бұрын

Well said!

@digisports22

3 жыл бұрын

@@myharris Thanks for clearing that up for me.

@plazmotech5969

3 жыл бұрын

exactly what I just did!

I think that is one of the nicest and well thought out welding tables I've ever seen.

You have definitely have given me a lot to think about when I will be ready to build a bench. I especially love the removable thin bars that you put in between the plates and your stops that are movable around the outside of the bench.

Nice to see both of your little helpers again. The bench is very well thought out. Nice job.

That table is a thing of beauty. I don't even weld and I was still drooling over it. Fantastic design and work!

@PaskMakes

3 жыл бұрын

Thanks very much - I was thinking it would make a cool dining table or desk but obviously with much thinner steel. :)

@goldenghostinc

3 жыл бұрын

@@PaskMakes I love centimeter of this thing. It's a work of beauty that I would be proud to have in my house. Not sure at all if thinner steel would improve upon that :)

It's the attention to detail that makes these builds and videos so amazing! Going back and putting extra tape on each bar rather than fudging it. Keeping the sides square, grinding the weld/installing screws replacing with rubber stops so the spacers sit exactly right. Not to mention thinking about the fact the rubber should go on the bar not the table. Then removing the mill scale, waxing it etc ... Amazing!

Beautifully done. My son and I started watching your scrap wood challenge videos a couple years ago and now we're enjoying watching you learn new things. Keep up the good work!

Beautiful table, and well thought out. Good to see your welding is really coming on. Thanks for the video.

Really love the humble pride that shows in your smile when you look at your finished table. I can tell you're pleased with how your project turned out, and rightly so. Job well done!

@PaskMakes

3 жыл бұрын

Thanks very much - I must say that I am pretty pleased with it! :)

brilliant mate! from inception to design, to execution, absolutely brilliant! its more than heartening to see a craftsman find and implement a solution to a problem, small or large, instead of "making do". so many just let it go half-arsed and live with it, using the initial flaws as excuses for substandard results.

Love when two of my favorite channels meet! Awesome work!👍🏻👍🏻

That is a bench to be proud of Neil. Well thought through & every step done to perfection. Enjoy it mate.

You're going to get years of service out of that one, great design and build! Thanks for sharing it.

Nice work as usual! I love watching Jason from fireball tools...he does some excellent fabrication videos and that water jet is crazy. Glad you found him :)

@PaskMakes

3 жыл бұрын

Thanks! I've only watched a few of his videos but really enjoyed them and will definitely watch more! :)

This table is a thing of beauty! You did one hell of a great job Sir!

Epic !!! That’s one of the best welding tables I’ve ever seen. Strong work !!! 👍🏻👍🏻

Loved the “beauty shot” of the pups.......oh and your table came out awesome too. Well done my friend.

@PaskMakes

3 жыл бұрын

I don't think they've been in a video for a while so thought they needed to make an appearance. :)

@MJ-nb1qn

3 жыл бұрын

@@PaskMakes - Yes Loved the Pups!

Every time I watch your videos I get the same enjoyable experience. I feel deeply impressed by your craftsmanship, your diligence and wide-ranging knowledge. With the best wishes for you and your upcoming projects, I will look forward to your future videos. Thanks for sharing. 👍

Man, this is a work of art! For me that only have basic steelworking tools this looks so much more achievable! I loved the video!

Really a well-thought-out project that finished up nicely and will provide years of good service. Well done!!

It's looking really good. Everytime I wear shorts when welding I send a spark down a shoe. Fireball makes great tools and videos.

Thanks for this wonderful distraction... can't wait for part 2. And thanks for owning up to mistakes... it is always interesting to see how you recover and I love your problem solving idea...they always lead to a great final product

Your work ethic inspires me to be more precise and do more planning in my own workshop. I’m not and I never do but I’m inspired none the less.

Love watching your videos. They are the best out there. You don't just make, you teach while you do it and that is impressive.

As an amateur with woodworker, i typically feel overpowered with the entire arrangement kzread.infoUgkxrYREG3-7f1Aqk9ams3ZESRNzGnfdUtyQ . Be that as it may, this arrangements drove me through with much clarity and effortlessness woodplans. Works i now work like a genius. That is great!

What a beautiful design and creation, Neil. One of the most aesthetically pleasing welding tables I've ever seen. I love it! Great trick with the vinegar, I must remember that one.

This is one of the coolest pieces you've ever made. Very impressive!

You are an absolute legend sir Pask, you manage to entertain me in most of your videos and that means you have done it to other viewers as well. You work meticulously and I am sure metal works is just a piece of cake to you. Keep up the good work!

Beautiful work! That’s a beast of a table.

I think that Jason at Fireball Tools would approve! Well done that welding table would have a place in any decent fab shop for sure! Your versatility in making stuff always impresses. Cheers from Tokyo! Stu

@PaskMakes

3 жыл бұрын

I hope so Stu! Thanks very much! :)

Can't wait to see what you do with it. Those removable slats are seriously clever.

Pask, I have thought of building a welding table but my ideas were just over complicated. This is so clear and functional and so elegant (in terms of design). I really appreciate your work. Thank you.

lol, even threw in a pair of bench dogs at the end

I need to make a sign in my shop “ Chill Dude, Neil makes mistakes also”. Great design as always Neil!! Welding was spot on also.

@PaskMakes

3 жыл бұрын

Thanks mate! I make plenty of mistakes, I'm sure we all do. Not sure the welding was spot on but I reckon it's good enough. ;)

@peterpan8685

3 жыл бұрын

I thought the same. :-)

Clear, crisp, excellent pace and production values. Just lovely. Well done.

Your attention to details are remarkable. Very well thought work from start to finish. Congrats.

This was a very satisfying build to watch.

I really like watching you work, your voice is very calming, and the fact that you allow the woodwork noises to make it sound natural

@vikassm

3 жыл бұрын

I was going to say the exact same thing!

@PaskMakes

3 жыл бұрын

Thanks very much - glad you're enjoying the videos. :)

I really like the table! I'm excited for more metal working on your channel.

Brilliant thanks Neill, shared it with my brother and hubby. Love the pups, they are so cute

While I was in college, I worked summers at an industrial plant (FMC) and became familiar with both welding techniques and tools. I just want to comment that your design, fabrication, and versatility of this table is extraordinary. The absolute utility and finish are exceptional. Best to you and the family, give the pups a hug, and be healthy.

@PaskMakes

3 жыл бұрын

Thanks very much! :)

That's an excellent, well thought out table. Well done Neil, oh and hey that shirt looks good too :) Thanks mate.

@PaskMakes

3 жыл бұрын

Thanks mate and thanks for the shirt, Love it! :)

@gregnorvell9730

3 жыл бұрын

The 2 of you should collaborate a project together and donate or sell it or whatever......?

Awesome work man. I’ve seen a lot of these videos but yours seems like one I would actually consider making for my shop. Great video!

Hands down the best welding table I've ever seen. I have seen a lot. Great work.

Nothing like cutting your freshly welded piece apart - one thing I have learned watching youtube, we all make mistakes. Even Pask Makes Mistakes :-)

That's a great design Neil!

@PaskMakes

3 жыл бұрын

Thanks Justin! Glad you like it mate! :)

@juliestafford2123

3 жыл бұрын

@@PaskMakes 0

@joelmiller3333

3 жыл бұрын

@@PaskMakesesx 3

@kingpin76110

3 жыл бұрын

@@PaskMakes did you ever make any plans or cultists for the ultimate welding table? I would like to copy it if you didn’t mind. Thank you.

Everytime I watch your videos, it reminds me that I miss living in Banyo/ Brisbane. Australia is an amazing country!!

Yet another great use of the 3 point principal. Thanks for showing it. GREAT table!!!

Another, classic, OVERKILL by Neil. Nothing new mates, just a solid, lifetime guaranteed construction for the generations to come... Cheers and many many beers for many many years mate!

First off, great video. As a helpful idea. When your tacking any square together try just tacking the inner edges together first. This method in conjunction with your gaps between your pieces will allow you to measure, squeeze, and pull the cross ends together and apart to make everything nice and square. Then when you tack the outer edges it will lock everything into place. That's how we trued up the ladder skids I built for a pump company. You can pull your measurement cross ways then use a ratchet strap for big stuff or push it on end against a wall until both measurements are the same then tack the outside and check for twist like you did. Hope that helps.

@serdiefgotreb

5 ай бұрын

It's actually the complete opposite. You always must try to tack the outer sides, it's easier to push inwards that to pull outwards

Very nice and simple design for a welding table. Keep up the great craftsmanship and hard work. Can't wait to see next video.

you're like the Bob Ross of making. love watching you work!

Cool!!!

@user-sc7zr6ly1y

3 жыл бұрын

ใ. .ใใ..ใ....ใ

@muzamilpathan748

3 жыл бұрын

Bfj

@totallyjonesin

3 жыл бұрын

Here is one of my favorite welding table vids. kzread.info/dash/bejne/fIWW04-CdJrNZ7w.html

Very nice! Wonder if I could make room for something like that!? Space is limited...

I want that work bench. The blue with the bare metal looks amazing. Good job

I love that you are obviously also getting carried away, when doing a project - and then realizing that the plan was different. Great to see all the turns you take - makes it much more authentic than skipping the "mistakes"...

I have to admit, I watched all the way through and wondered why you were doing the slats, when it would be easier to just weld a big bit of plate on the top, then you showed the clamp part and I literally said out loud "i'm an idiot" - excellent work as ever :D

@JDeWittDIY

3 жыл бұрын

Another method people use is a solid top with holes drilled and special clamps for the holes. But with the slat method, there's no holes until you remove the slats.

I see old milk crates are just as handy on the other side of the world too!

@TheAefril

2 жыл бұрын

Who says they have to be old, I have about 12 of them around the yard. I use them for scaffold, stools, temporary ladder, welding props, formwork support and chairs. I use milk crates for just about any temporary furniture or stand inside the house, garage, and around the yard. They are modular and give you a new level of 320mm above the floor, so handy.

I really like this video. I just started metal working at the beginning of Covid and have been interested in building a table like this. I was happy to see that you made a metal working video!

Simply said: amazing! Keep on doing this videos and products, entertaining and creative. Thank you!

Being in a similar wet environment, I would love to know how the wax on the table top works out. How often you have to reapply it, effectivness, level of effort, would you do it again, etc. Great build!

@PaskMakes

3 жыл бұрын

Yes it will be interesting to see. I think whatever finish goes on, there has to be a degree of maintenance. :)

@Gottenhimfella

3 жыл бұрын

@@PaskMakes I'm sure it will help with preventing spatter from adhering, especially if it's reapplied regularly

I have the Fireball Tools squares and can say I find the "3 point" method much more simplified and easier. 3x of 2" angle iron with a square tube clamped across the top works great. The custom squares come in handy here and there but have found that they stay in my tool drawer a lot. They are indeed good for welding upright legs in corners though, but with a little work you can make your own squares out of tube as well. I also want to give a word of caution. If you are going to be welding anything for more than 20-30 minutes, never wear shorts or short sleeves. In fact I never recommend shorts at all, ever. It's far too easy to get UV burn and weld spatter in your shoes or boots. Long pants..always. Lastly, I see no reason to have the filler bars at all. And to remove mill scale, the best answer is pre-soak in muriatic acid for 30 min to 1 hour, then immediately after that, dip for another 30 min in phosphoric acid, otherwise the steel flash rusts. Phosphoric gives a rust prevention coat. Vinegar really does nothing except oxidizes and rusts. It's often used in a mix to patina metal for a rust look.

I love to see your process in action Neil, awesome work!

I love your channel. You make everything with thought, precision and care.

"Can't even follow my own plans" I AM NOT ALONE after all !!!!!!!

That table makes me feel things that my wife hasn't made me feel in years.

@juancarlosricarti7215

2 жыл бұрын

Jjjjjj maybe you need a blond neighor table to "weld" jjjj only a joke (mmm...)

I finally got the correct way to designate those casters & was able to order a set. Thank you for sharing your table. I will likely make a similar one.

That, sir, is the king of work benches. Well done. Beautiful work. Thanks for sharing.

I’d love to mimic your table with exactness. Would you share all the dimensions?

just search for "FOOTMASTER Plate Casters" on amazon

@NotYourIngenue

3 жыл бұрын

Thank you! I was specifically digging into the comments to see if anyone had answered what those casters were. I think I need some.

Beautiful table. Great concept with the removable slats. Well done.

Brilliant workmanship, as is all your work I've seen. Bravo.

Fairly new subscriber and as always I enjoy watching your ingenuity Neil! I always look forward to the next one!

Fantastic work Neil! A very solid welding table indeed.

Nice work mate!!! One of the best tables I’ve seen. Great video and description.

Congrats on the new table, and great design! What a gamechanger!

That's an awesome design! if I had a shop, that looks like a fantastic project for a simple yet functional design. Also, glad to see you got new boots!

Excellent approach, Neil! I love the way you solved the clamping space with the removable spacers and the stops. Well done! Thanks for sharing the process.

@PaskMakes

3 жыл бұрын

Thanks very much Luli! :)

Your work is incredible, and you too Neil!

Thanks for showing when you make errors. It's nice to see that errors will happen, and are not the end of projects. Love your videos.

Beautiful work, Sir. I will need to watch again for all of your ideas.

you should feel very proud of that work platform, its gorgeous!

Have ordered a set of those wheels. Very useful and great timing for my next big project. Thanks for great video.

Great job, I normally wouldn’t watch a 19 min video of someone building a welding table but your attention to detail made me watch the whole thing.

The little extra bits make it really turn out boss, great job fella

Love ya work man, great seeing an Aussie creator using materials and tools we can get from the big green shed and other local shops

@PaskMakes

3 жыл бұрын

Thanks Ken! :)

I love your new metal working table. Great design. My you have many years of creative adventures with it. Thank for sharing

Best table build I've seen yet. Nice work.

honestly, this is beautiful enough to put inside the house! ... amazing job.

I love watching your videos, and I love how you arent afraid to admit you are human and make mistakes like the rest of us. It takes the pressure off, to know I can something new and not do it right the first time.

Neil, thank you for sharing. Enjoyed this build!

Great video again Neil. Nice to hear Jason at fireball getting a mention, I have one of his squares and its a massive help with frames like this. well worth buying.

@PaskMakes

3 жыл бұрын

Thanks mate and great to hear your thoughts on the Fireball square! :)

I reckon your reckoning is spot on as this bench is brilliant. So many things I need to build but my new shop takes the top slot for now. Great job bud...👍

I Really like this table. It is one of the best simple designs . Definitely one to be proud of.

Love the table concept. Don’t know how you do it, but your ideas are always so clever, attractive and functional. Thanks for sharing...... 👍👍😎👍👍

Congrats, the best DIY welding table I have seen on YT. Cheers.

Amazing looking table, great job planning and building it Mate !!

Nice work, ol kid. That's a great setup and design 👌

Very nice and DIY-friendly design. I also don't have enough space to have multiple tables and will have to stick with 1 for all my projects. This has given me good ideas.

Awesome Build. I can't wait to see the Pasks you'll Make with it!