I've installed these strips under counters many times as a contractor. You only need to connect wires to one end as long as you don't break the strip. Great idea. Some kits come with RGB and remote controller/dimmers so you can tailor the light to the K or color you want. They should be able to be made portable by just setting up with batteries to the value of the adapter.

@DroiMedia

3 жыл бұрын

Thanks for the comment and info, Bill!

@robertburdett5028

2 жыл бұрын

While it's true that you don't necessarily need to attach the power at both ends, it is possible that with longer LED strips , brightness and voltage can drop toward the end of the strip(especially when chaining strips together). I linked an interesting article describing the problem. One solution to double the possible length of a strip is to attach power to both ends as he did in the video. www.superbrightleds.com/blog/understanding-difference-12-volt-24-volt-led-strip-lights/3070/

Fantastic DIY Build! I had been looking at several other DIY attempts, and this is by far the best, most concise and followable one! Thank you Droi Media! I know you are addressing an American audience, I live in Germany and it\s been a little hard finding frosted acrylic tubes here. Been to home stores and Bauhaus stores and they don\t really know what I mean. So far the best translation term I have for anyone else searching in Germany is 'Acryl Rohr Satiniert"/ Thanks!

@DroiMedia

4 жыл бұрын

Thanks for the comment! Keep me posted on what you find - I know a few other folks found clear acrylic tubing and just put a layer of diffusion inside for the same effect. Happy DIYing!

@SebastianKaye

4 жыл бұрын

@@DroiMedia Cheers! great suggestion. Will keep you posted what I end up making on this build :) What would be a searchable term for a 'diffusion layer'?

@DroiMedia

4 жыл бұрын

@@SebastianKaye I think they were maybe using lighting/gel diffusion filters (like these: amzn.to/3elKMQn) - but you could probably get away with something cheaper like parchment paper (that you use for cooking).

Thank you for sharing. I'm excited to go and attempt your design as soon as I can. Think I'll try with RGB LEDs.

@DroiMedia

4 жыл бұрын

Awesome! Let me know how it turns out!

Hi Mr. Adam, I am from India. I used to wonder why my desklamp's light used to feel "dead and cold". Now I know that it used a low CRI LED(probably much less than 80). Thank you for this knowledge. KZread is a wonderful place. I am now searching ways to make a durable LED tube myself. Usually the manufacturers use a bad quality power to the LED tubes here. and because of that, the tubes die within a few years of purchase...even if the LEDs work mostly fine. I am trying to overcome planned obsolescence and make my 10 year-LED tube on my own.

@DroiMedia

2 жыл бұрын

Awesome to hear! Let me know it goes! :)

Have been looking for something like this for aaaages, great tutorial.

@DroiMedia

4 жыл бұрын

Thanks! Share a pic if you decide to make some! 🤗🤗

Awesome. Simple but very innovative! Thank you for this!

@DroiMedia

3 жыл бұрын

Thanks for watching (and commenting)! :D :D :D

That was amazing... Thanks for Sharing... I love tools.... and I think this is going to be one of my future projects. Thanks a million. You just might have saved me $100s.

@DroiMedia

3 жыл бұрын

Glad you liked it!

Clear instructions and easy to follow.

@DroiMedia

4 жыл бұрын

Thank you! :D

Clean build! Thanks for sharing!

@DroiMedia

4 жыл бұрын

Thanks for watching! :D :D :D

Easiest and most comprehensive video I’ve seen.🤘🏽

@DroiMedia

2 жыл бұрын

That means a lot, thank you! 😊😊😊

Great stuff! Here in the uk,18 inch t8 led tubes are difficult to find for my lamp that is a perfect length for my desk,so will give this a go!

@DroiMedia

2 жыл бұрын

Awesome! Let me know how they turn out - and share some pics with us once you're done! :) :) :)

Looks awesome and Dam that’s bright! You should consider getting the leds with the remote to dim them down if it suits your needs or to change the color

@DroiMedia

3 жыл бұрын

Thanks! And I actually did that for my second build - has worked well so far :)

It was simple and clear. Thank you 🙏

@DroiMedia

4 жыл бұрын

Thanks for watching! :)

Can’t wait to try this!

@DroiMedia

2 жыл бұрын

Doooo ittttt! And then let me know how they turn out :)

Fantastic. Thank you for sharing

very clean diy! looks very professional

@DroiMedia

4 жыл бұрын

Thanks!

Most excellent. Well done!

@DroiMedia

3 жыл бұрын

Thanks! 😊😊😊

Awesome vid man! Subscribed! Look forward to watching more. Cheers!

@DroiMedia

4 жыл бұрын

Thanks! That seriously means a lot - appreciate the comment and the sub :) :) :) :)

@RonnieRabena

4 жыл бұрын

@@DroiMedia No worries!

Great work !

@DroiMedia

8 ай бұрын

Thanks!

really amazing! thank you so much!

@DroiMedia

3 жыл бұрын

Thank YOU for watching and the kind comment 😊

amazing video. Thanks

@DroiMedia

Жыл бұрын

Thanks for watching! :) :) :)

Fantastic! I've been thinking the last few weeks about how I need to build some tubes before these tariffs get too crazy, but I might have missed my chance. I was thinking about using fluorescent tube protectors as the tube and spraying them with spray on window frost, but I might have to check out the acrylic tube you used because i'm sure it's much more durable.

@DroiMedia

4 жыл бұрын

Saw those very tube protectors at my local hardware store and realized if they were totally stationary (i.e. just lived in a studio somewhere) they might do OK, but the acrylic tubes are as thick as a PVC tube so I'm guessing they could withstand a good amount of abuse if you need them to work out in the field or get moved around a lot. Let me know what you decide to go with - would love to see the finished tubes!

@datguyesef6

4 жыл бұрын

before i got quasars i did the exact same thing. Got the tube protectors and sprayed with window frost. it looked good and worked. this is a video with them kzread.info/dash/bejne/oGWJq5Wanqzfn8o.html

@kennmossman8701

4 жыл бұрын

There are two types of plastic normally used - each has its advantages

Superb what a innovative idea congratulations 👏to you

@DroiMedia

2 жыл бұрын

Thanks!

Found you on Reddit....thanks for sharing man. This is one of those questions that plagues KZread’s. About lighting.

@DroiMedia

4 жыл бұрын

🤗 happy to help!

@spiritualityjuice

4 жыл бұрын

Check me out too man. Let me know if my content jives with ya.

This is how diy video suppose to be. I just watched a video and 5 minutes in on a 6 minute video the guy was just talking nonsense and zero how to...lol. Thanks for the idea.

@DroiMedia

3 жыл бұрын

Thanks! I do my best to just showcase the DIY stuff, and as little of the other shit as possible :)

@rogeers2167

3 жыл бұрын

@@DroiMedia i mean some vids can get away with my pet ;peeve of all talk no diy but you have to look good in a bikini ...lol

@DroiMedia

3 жыл бұрын

@@rogeers2167 I do NOT look good in one, so I'll keep up the DIYing :D

Great idea! Tanks!

@DroiMedia

3 жыл бұрын

:D

5:23 am dead 💀 😂😂 didn’t expect that lol 😂! You a genius! God bless you you save me lot of money

@DroiMedia

4 жыл бұрын

glad to hear! Thanks for watching! :D :D :D

Hey thanks for the video, I'm currently looking at parts for a project for my custom water cooling pc where I use frosted white tubing and I'm planning on using ARGB lights Behind the tube. Unfortunately I cant seem to find any reference photos/videos of other people doing something similar so your video is just what I need to get a sense of how the diffusion looks

@DroiMedia

Жыл бұрын

Glad I could be of help - would love to see what the finished project looks like, @ me over on Twitter or Instagram if you post some finished shots.

awesome .. great stuff

@DroiMedia

3 жыл бұрын

Thanks so much! :)

WOW !!!!!! Such a beautiful idea !!! Super thank you for sharing this tutorial !

@DroiMedia

3 жыл бұрын

Thanks! 😊😊😊

@MusicAndOtherColors

3 жыл бұрын

@@DroiMedia Have you tried to make a portable one as well ?

@DroiMedia

3 жыл бұрын

@@MusicAndOtherColors they are readily powered via external battery banks, so somewhat portable. I have yet to make one with an integrated battery of any kind, honestly I think that's out of my realm at the moment. :)

@MusicAndOtherColors

3 жыл бұрын

@@DroiMedia I guess it is doable but it would cost a bit more , I want to use it for outdoor shootings

@DroiMedia

3 жыл бұрын

@@MusicAndOtherColors Yeah, just use a battery pack (I have a few that I like listed in our 'how we power our gear' video on the channel) and you will be totally fine to use outdoors. It's definitely portable enough to move around outdoors, the packs I use are like half the size of a toaster.

Nice and neat work. thanks for the great content...

@DroiMedia

4 жыл бұрын

Thanks so much! Appreciate the feedback 😊😊😊

@Vandan9166

4 жыл бұрын

@@DroiMedia It's the truth and I like feedback as well, cheers!

So awesome man! If you could make a portable version it would be even more epic. Not many companies make those it seems except quasar science

@DroiMedia

4 жыл бұрын

Thanks! And I know, I want to make one with an Incorporated battery but haven't been able to make it work yet.

@FelixFukuyoshi

4 жыл бұрын

Droi Media that’s great, I hope you’ll succeed and make a video out of it!!

@jddang3738

Жыл бұрын

@@DroiMedia not sure this will work (didn't show the process) but this guy hooked up a Sony battery plate to his lights kzread.info/dash/bejne/YoWjx9CDn5yacco.html

it's so cool! 我太喜欢了！！！

@DroiMedia

4 жыл бұрын

thanks!!!

Awesome! Making mine this week. Any tips or thoughts on battery powering this?

@DroiMedia

4 жыл бұрын

I haven't taken the time to make a battery powered one yet, but you can run power off a small battery powered generator or power brick, just gotta check the #s and make sure it'll handle the LEDs. Check out our Powering Your Gear video for the one we use!

Thanks for this vid will use it, Just a thought, instead of a wooden dowel an aluminum tube would work well, It will help with the heat dissipation and you can put the wire inside, though endcaps will be tricky to fasten.

@DroiMedia

3 жыл бұрын

Great tip!

So sweet

we enjoyed with Ur video its so easy cheap excellent

@DroiMedia

2 жыл бұрын

Thanks!

Incredible! How to save money on the quasars! I wonder how these fair with flickering - they looked great on your video?

@DroiMedia

3 жыл бұрын

No flickering I've encountered yet :)

Do you still have some of those endcaps...I'd like to get about 20 of them...what would you charge for them as I don't want to buy a bulk when I only need a few. Thank you.

I'm going to make a kids-car illuminated roll bar with flashing lights using this technique. I have an old three-color LED strip and a wig-wag flasher module. Tks!!

@DroiMedia

4 жыл бұрын

Awesome! Be sure to share a picture with us on social media after you're done!

Could be nice a portable version :D you made my day wth this tutorial. one sub here

@DroiMedia

3 жыл бұрын

🤗 happy you're here! Let me know how it turns out if you make one!

nice build pro

@DroiMedia

4 жыл бұрын

Thanks! ☺️☺️

Dowel idea was very neat loved it. I would have loved to use a steel or copper rod as it also works as a heatsink.

@DroiMedia

3 жыл бұрын

That is good to know, I haven't had anyone tell me that yet, I might have to try it out on my next one! Thanks!!

@jec_ecart

3 жыл бұрын

@@DroiMedia wow. That's a lightning quick reply.

@DroiMedia

3 жыл бұрын

Caught me on a lunch break, plus I don't have a ton of subs so I keep notifications on 😊

@jec_ecart

3 жыл бұрын

@@DroiMedia that made me subscribe you ! Good luck.

Nice! Thanks

@DroiMedia

3 жыл бұрын

Thanks for watching! 😊

I loved how this led tubes ended up looking! I'll try to make my owns, but I wonder if it would be possible to power them with a NP-F battery or simillar, to make it portable. What do you think?

@DroiMedia

4 жыл бұрын

Hey! That's honestly the most common question I get asked.... I think if you got one of those NPF batts with a USB out or something you could power one that way I bet. I haven't had any time to test that option out but maybe some day :)

@deanv8663

3 жыл бұрын

I use LiPo remote control plane batteries for some of my led stuff. They are small, light, and can be found for rather inexpensive prices.

@gokulhbk

3 жыл бұрын

@@deanv8663 Just found your comment, I was plannig to make a portable version of these light tubes, do you think it is even 'possible' to get this much brighntess and to shelf a battery without making the entire system too 'bulky' ? Thanks

@deanv8663

3 жыл бұрын

@@gokulhbk the batteries I have used are about the size of a tic tac container.

With cheaper strips the mounting tape is crap - glue it down with epoxy. Just put the epoxy directly on the surface, then apply the strip. The sticky tape will adhere.

Awwwww mate - we are definitely going to make some of these bad lads! Great video as always.

@DroiMedia

4 жыл бұрын

Do iitttt! Seriously they are great, let me know when you end up making some, would love to see what you guys come up with! Thanks for watching :D

Thanks for this guys. I'm definitely going to try, do you have any suggestions for colour changing LED strip or would this not viable?

@DroiMedia

4 жыл бұрын

Hey Richard! Thanks for watching - as for the color changing strips I've got a set that I'm working on putting into one of these, the only issue I'm running into is that additional strip that runs under the LED strip is 4 wires with RGBW and they require additional connecting hardware (rather than soldering 4 sep. wires) so it's a bit 'chunkier' than I want on the inside and doesn't fit as well. I'm hoping to get some time this month to finish that up and I'll share a post on the results when I do. Honestly, I might just try it without that other wire and see what happens.

@richardtyson5248

4 жыл бұрын

@@DroiMedia Good luck! Can't wait to see the results. I will try and the Daylight ones then go again should you make the colour work. Thanks again for the video and keep up the great work! P.s. I am the worst DIY person so fingers crossed

Well done, if i want this in another colour is it possible to spray the acrylic pipe with a clear paint?

@DroiMedia

4 жыл бұрын

I don't see why not! They also have other colors of plastic tubing if you wanted some color.

If you 'tin' the copper pads on the strip before soldering the wires it is much easier/faster. Applying some flux beforehand can also help.

@DroiMedia

4 жыл бұрын

Hey Kenn, quick question - I've got an RGB light I want to use for this build, but it's got 4 cords and a 4 pin connector for power on either end... so I'm unable to run the wire along the dowel and connect to the top and bottom (hope that makes sense). What issues would I be running into without that? On another forum someone mentioned that wire helps distribute heat and voltage evenly throughout. Any input is much appreciated, and thanks in advance!

@kennmossman8701

4 жыл бұрын

@@DroiMedia I think you mean wires (and not cords). That's what I thought you did for the White LED strip which surprised me because it ought (!) not be necessary as "good" strip vendors state (how much truth there is in it is debatable) you can daisy-chain up to four 5m strips. I have only one installation of a 5m strip and the brightness SEEMS uniform. Thanks for reminding me to actually check the voltage at the non-powered end just to see how much of a voltage drop there is.

@kennmossman8701

4 жыл бұрын

@@DroiMedia The copper tracks / traces on strips (and such) are both thin and narrow which causes a voltage drop and so the LEDs at the non-powered end could be dimmer. The voltage drop is directly related to the current which is related to the density and type of LED (i.e 5050 versus 3825). Generally speaking, the 'bigger' the LED and more the number of LEDs the higher the voltage drop. I have seen powering LEDs as you have done (from both ends) which ought to balance the voltage (and so the heat would be uniform). I would not say the heat was distributed evenly as flexible strips "do not" distribute heat.

@kennmossman8701

4 жыл бұрын

@@DroiMedia Soooooooo! I see you have a few options. Ask the vendor for a RGB strip with the lowest voltage drop (I doubt they will have any idea as to what you are asking though) , or measure it for yourself. If the drop is more than say 0.2V then you could do as before (use a router to make a groove for the wiring), or run a buss wire at both the top and bottom. A buss wire is simply a thick wire meant to carry power to circuits with minimal voltage drop. There are Wire Charts available that give the raw data needed to determine the voltage drop for a given length and current

@DroiMedia

4 жыл бұрын

@@kennmossman8701 thanks for this thorough reply (and yes I meant wires, long day lol), I appreciate your insight!

Great stuff! I need enlightenment about where the four wires at the other end come from. Also, how do we decide whether it is 12 volt or more. Thanks.

@DroiMedia

3 жыл бұрын

Thanks! And the four wires at the other end? Let me know what part of the video you're referencing and I'll let ya know (sorry it's not more obvious to me, just getting back from an all day shoot outside in a field so my brain is mush). As for the 12v, I believe the LEDs are all 12 [if I'm wrong and someone else with more information/knowledge is reading this please correct me!]

@sharifsalem

3 жыл бұрын

@@DroiMedia low voltage LEDs come in 5v, 12v and 24v. They also make line voltage (120/240v) LED tape/rope but less common. You oddly did use 4 wires, two at each end of the tape which is rather unusual. What is the reasoning for doing that.

@DroiMedia

3 жыл бұрын

Hey! Thanks for the comment! I think you're referencing the two wires I used to connect the LED strip to itself (each wire was bare at both ends so there were 4 bare areas that I connected, butonly 2 actual wires). Anyways, I was told by some folks this was the way to do it after my first tests ended up with WARM LED temperatures. They said this method would distribute heat / current more effectively. I have like NO knowledge on this shit though but it definitely worked out in terms of keeping the LEDs a lot cooler!

Hello just finished the build. Thank you very much for the tutorial ! I have a problem tho I can see the individual led through the tube, it looks like its not diffused enough. Could it be because i used cheaper led (not the 90 cri ones) ?

@DroiMedia

3 жыл бұрын

Hey! Awesome to hear that you took on this build! It COULD be that, are you able to see the bulbs through your camera? In person I can see the individual bulbs, but on camera unless I have a really small aperture (f9 or higher for instance) or a really high shutter speed I can't see the bulbs.

@illegalmexicain

3 жыл бұрын

@@DroiMedia oh it wasnt meant for a camera lighting in my situation, it is meant a dance performance haha, so I have to get rid of the single led visible effect. I just did a quick research on aliexpress and found some led flexible strip that might fit my need better. Also the caps where kind of hard to get in my country, so I 3d printed them (with a guide for the dowel rod, a hole for the screw and one for the wires to daisy chain). You could link them in your video if you want (used the same frosted acrylic as you did).

Any idea how you would throw this on a cold shoe for a camera? Been thinking about making my own portable light with all these neopixels I have

Do you know the % light transmission from the tubing? It's super hard to find frosted acrylic tubing in the Netherlands.

@DroiMedia

4 жыл бұрын

Great question but unfortunately one I do not have an answer for. However, you could get clear plastic tubing and then put a rolled-up piece of frosted gel on the inside for the same effect I would think.

thanks for the vid! one question tho, what if i have a strip that changes colors?

@DroiMedia

3 жыл бұрын

Works the same way! My RGBW strip has 4 connections / wires (is yours the same?) so I had to solder an additional 4 wire strip to each end. I bought some solderless connectors but they didn't work well.

If you have to solder a power connector then try using a molex style connector or terminal strip. The 'barrel' type connectors are a huge pain-in-the-@ss. This is also true for 'external' runs as the barrel connector easily pulls apart

@DroiMedia

4 жыл бұрын

Kenn thanks for all this insight - I truly appreciate it!

Hey man, you wouldn't happen to still have any more of the end caps, would you? If so please lmk! :)

@DroiMedia

3 жыл бұрын

I'll check and let you know but I THINK I've got some left, if you can shoot me an email so I don't lose track of this request! hi@droimedia.com

What's the purpose of running a separate wire from the other end of the tube, can you not power the led strip from one end?

@DroiMedia

4 жыл бұрын

Hey! I've been told by people with much more experience and knowledge than me in this field that the wire will help regulate power throughout the length of the light strip, so it's less likely to overheat at one end. Thanks for watching and let me know if you have any other questions!

Hey! This has been a very informative video. Would you possibly know how to make this tube light rechargable using usb? if so it will be lovely to connect with you to get some insights from you. Cheers!

@DroiMedia

Жыл бұрын

I haven't done it but it's totally feasible, would need to wire in a battery pack that you could recharge or swap out or whatever. This was high on my list of projects but my wife and I had a baby last year sooooo that's been my big DIY project for the last several months haha

Nice

@DroiMedia

4 жыл бұрын

Thanks! :)

Hi Droi, awesome tutorial. can this also be powered by a 9 volt battery?

@DroiMedia

3 жыл бұрын

Hey thanks!! I have no clue but I don't see why not - would just need a (maybe couple of) 9v adapters and then wire in the correct connection type.

@Modern-Crafts

3 жыл бұрын

Most LED-Strips run on 12V. If you directly connect them to a 9V Source, they might light up but only very dim. You could use a voltage step up module to boost the voltage to 12V. But you also need to make sure that the 9V Battery as well as the step up module can deliver enough current to power the amount of LEDs you are using.

@tcibeatrecords4707

3 жыл бұрын

Modern Crafts Thank you. I will try this set up........

good job mateen from pakistan

@DroiMedia

3 жыл бұрын

Thanks! :D

Can I have the link for the solderless connector you used for the build?

@DroiMedia

4 жыл бұрын

Hiya! I think this is the one I used: amzn.to/2O7G7qM

great idea but won’t they work just adding power to the one factory wires with out soldering the end you cut?

@DroiMedia

2 жыл бұрын

It will work - but I did this initially and it gets REALLY WARM, I explain it a little more in depth in the video and some other comments, but essentially closing the circuit (or making a loop - i.e. soldering both ends in) distributes the power better and the light doesn't overheat.

What's the purpose of running the red/black wire under the strip and powering the stripe on both ends? In normal LEDs like Govee from Amazon the power is only connected on one side. Pls let me know. Am in the process of making my own LED tube light. Thanks

@DroiMedia

Жыл бұрын

Thanks for watching - as noted in the video, you don't HAVE to connect the wire to both ends, but it helps distribute the current / heat better (in my experience). Will work either way though! Let me know how it goes, would love to see some finished work! :)

How would you do this to make it battery operated or usb powered to plug into a portable battery for portable use?

@DroiMedia

11 ай бұрын

Probably the most common question I get asked about these.... I don't have a great solution at the moment. I have toyed with the idea of using a hollow tube that would fit AA batteries in lieu of the dowel rod that would power the entire light, just haven't found the right stuff for that. Otherwise a small USB battery pack that you attach with velcro to one end would be the easiest solution (and then you just need to get a USB to 3.5mm power cord). Again, haven't tried that. I typically just plug them into a larger battery pack I carry around that I charge camera batteries and stuff from - at the very least it allows me to put the light in spots that would be a bit more restricted if I needed a long extension cord and wall outlet access.

Very nice! Hey, do the same for a RGB model!!

@DroiMedia

4 жыл бұрын

I did! Just didn't make a tutorial for it :) It's a 3' long RGBW version, remote controlled, pretty good except a few of the LED bulbs never do the color I want (but it's OK since I can just turn them to face away from the shot/camera/subject!

@CPProd

4 жыл бұрын

Awesome, do you recommend good LED lights strips for RGBW, cause the ones you used have this problem? It is difficult to find a good and reliable LED strip that has a good (and real) CRI.

@DroiMedia

4 жыл бұрын

@@CPProd I bought a decently reviewed one and still had those problems. I opted for a lower CRI (IIRC like high 80s, so not great but I figured whatever since I am only using it for very specific instances) so that might have been the issue? I haven't used one I am really happy with, but I do have a few really high CRI, really highly rated, really expensive ones I want to try out but I'm just nervous about spending like 3-4x what I want to get a damn LED light strip that I use occasionally ya know. SO, long story short, I don't have a recommendation at this time unfortunately - except to just find one in your budget with decent reviews and work around whatever the shortcomings are :)

@CPProd

4 жыл бұрын

@@DroiMedia Right, my friend! You are right, the budget and the usefulness of this tool for my work are absolutely the most important to consider. It is no use buying the best led (and more expensive) if I don't use this equipment so much. Thank you very much for your help and attention with my question! Success!

Is there any heat issue? Why led strips are used without radiators?

@DroiMedia

3 жыл бұрын

The only neat issues arise when you don't have the LEDs connected at both ends. And I don't know what a radiator is 😊

Can these be made to run on battery ? will it affect brightness ? if it can be run on battery ? could you tell if the battery would be huge or possibly portable

@DroiMedia

3 жыл бұрын

Yep! I run them off of some larger batteries sometimes to make them more portable, but you could definitely rig up some NPF or V Mount style batteries to power these - either of those options would be fairly small / portable.

@93FilmsandMedia

3 жыл бұрын

You could probably hook them up to usb connections

@DroiMedia

3 жыл бұрын

Great idea! I just run them into the 3.5mm in (light) from the USB out (battery). Works great, although not a "battery powered" as many people want.

Quick question: Why do you solder an additional wire to the other end (the one without the connector adapter) of the strip (at 3.25 in the video)? Is there any "performance" reason? sorry, i am a noob at electrics ;)

@DroiMedia

4 жыл бұрын

Great question! I was told by people with a better understanding of electronics than me that doing so will allow better / more stable flow of an electric current through the entire light that way. I have yet to test out and see if it makes a difference, but I know you could technically do it without that cord if you wanted (they're made to be used that way) to save a little time, money, and effort when making these.

@jgibbs027

4 жыл бұрын

It’s to mitigate voltage drop and idefinitely worth the small effort so as to maintain even power. Thanks for the tutorial, great job!

@DroiMedia

4 жыл бұрын

Thanks!

Why did you wire the opposite end back? Wasn't it getting power just from the input at the main end?

@DroiMedia

4 жыл бұрын

Hiya! (Sweet username 🤗) so I was told by people with more experience than me that wiring it that way helps distribute power throughout the entire strip and can help prevent heat buildup. You can definitely do this without it though!

@thankyouyahusha4957

4 жыл бұрын

@@DroiMedia thanks for the reply.

Will it have problem with heat accumulating inside the tube over time?

@DroiMedia

11 ай бұрын

Thanks for asking - and I only ever had them get hot when I DIDN'T wire them from both ends. As is they get warm since it is an enclosed space, but I have never really had any 'hot' issues. I do think if I could go back I would drill a couple air holes at each end to allow for some air circulation.

Either the website you bought the tube from changed the way they frosted their tubes or the exposure of your video makes the LEDs look way more diffused than they actually are. The 1.5" tube is too narrow to diffuse the LEDs and you end up seeing each individual LED through the tube. I purchased the samr stuff you did, am i doing something wrong?

@DroiMedia

11 ай бұрын

In person they typically show up as individual LED spots, but on camera they tend to look like the frosted tube you see in the videos. Yes, I exposed for them to look like that and then adjusted my other lights, but I do that for most shots so I hope that it doesn't seem like I'm misleading anyone here. I also notice that when I crank them to full power (via the dimmer in my follow-up video) the individual LEDs are a LOT harder to see. Let me know if you've found a workaround for this issue!

@squareempire

11 ай бұрын

@@DroiMedia thanks for clarifying. Yea that makes sense, since they're really bright so the dots won't show up in the video unless you underexpose. I'm using the light stick as a decorative light (it's really long and leans against the wall) and so having a smooth glow is what I'm going for. I'm gonna try it with a higher density LED strip and see if that works

I want to make my own grow lights for hydroponics. So my question is, can i control the lumens of the light? Are there stronger strips?

@DroiMedia

4 жыл бұрын

Hi! You can find different lights with varying amounts of LEDs online - these are a single strip with a light every inch or so, but I believe there are strips with two side by side lights or lights every 1/2 inch or so (so basically more lights in the same length of strip which means brighter lights). I would assume these would work as grow lights, they're as bright or brighter than the same sized light I use for my frog/terrarium :)

@moncefzerroug9533

4 жыл бұрын

@@DroiMedia thank you! for the great video and for your response! like and subscribe folks, he deserves it

@DroiMedia

4 жыл бұрын

@@moncefzerroug9533 thanks for the support :) :) :) truly appreciate it!

Whats the flicker like on these LED strips when filming video?

@DroiMedia

4 жыл бұрын

None that I've noticed but I'll do a shoot with them this weekend and share some footage - I'll run through some various frame rates and shutter speeds to see. Thanks for the question!

@kennmossman8701

4 жыл бұрын

That depends on the duty cycle and frequency if using PWM. I'd suggest varying the voltage or current instead.

Just wondering if you've attempted this using Bi Color strips? I'm pricing out an attempt to build and was wondering if you had sound advice?

@DroiMedia

4 жыл бұрын

Heya! I have indeed, I made some RGB awhile back, but the LED strips were not great (see pic: instagram.com/p/B8HyTj6Bzsp/) - there were some color issues in them. They work for most colors but that one was the most 'off' so I chose it for the pic. I would suggest finding some highly reviewed ones on Amazon and maybe spending a little more than you want to make sure you get a good set. Wish I had more guidance here but honestly I still use the RGB ones I made I just turn those two wonky LEDs to the back and they don't cause any issues.

@cinematographybycss

4 жыл бұрын

@@DroiMedia That's unfortunate. Maybe I'll price out a roll of Tungsten/Warm White LEDs an a roll of Daylight LEDs and make individual tubes, like a kinoflo. Anyway, this is a great tutorial. I sat down and priced out everything other than the LEDs tonight to make to 4x Banks. I have a few simple ideas to trick them out a touch more. Do you have any changes or upgrades to this build that you've already considered or tried? Cheers. Also, I subbed here and on Insta.

@DroiMedia

4 жыл бұрын

@@cinematographybycss Appreciate the kind words and the sub. So, I don't use my RGB as much as I figured I would. IF it was 100% on those bulbs maybe I would, but I use daylight balanced lights like 95% of the time. Just not a huge need for my current projects. As for the upgrades or changes I did go back in and resolder and heat seal all the connections (with like little black heat shrink plastic stuff). I then sealed up the ends with a little glue too when I popped them on. I felt like it provided some additional security / stability to the lights (or at the very least provided me with some additional peace of mind). Otherwise I haven't found any major upgrades or anything - but I'm always happy to hear what others are doing to put their own twist on them. Share some pics or info once you get yours done! :) :)

@cinematographybycss

4 жыл бұрын

@@DroiMedia I have a bunch of these cable key chains left over from another project I did a few years back. I was thinking of adding them to the end caps so the tubes could easily be hung on stands or on command hooks on walls for quick rigging. www.amazon.com/Pawfly-Keychain-Stainless-Outdoor-Hiking/dp/B07FCHKJV6/ref=sr_1_4?dchild=1&keywords=wire+key+rings&qid=1592970319&sr=8-4 Also I think I would use dual lock instead of standard velcro. And although it costs way more, a foldable baby plate so they pack down much easier seems like something I would want. At the moment, those are the only little changes I would make. Thanks so much for the feedback.

@DroiMedia

4 жыл бұрын

@@cinematographybycss I like the idea of being able to hang them, would be killer for music videos or some other creative work (sci-fi/horror). Might have to pick some up :)

Why does the LED strip need power to both ends? That’s the only part I don’t understand. Isn’t the point of the screw on end for power to avoid soldering?

@DroiMedia

3 жыл бұрын

Heya, this is explained more in a few of the other comments here but basically the other end connection / loop that it creates helps to distribute power more evenly and prevents over heating at the connecting end. Hope that helps! (You can get away with just the one end but when I did it the lights got hot)

Wow, I didn't know Austin Carlile is made such a handyman!

@DroiMedia

3 жыл бұрын

😊😊😊

Looks good. How's heat with this closed enclosure?

@DroiMedia

4 жыл бұрын

Thanks and great question! It gets slightly warm to the touch right now. I approached some friends with more knowledge than me after my first build got HOT, and they suggested I wire both ends (as seen in the video / finished build) - seems to work but I always try and keep an eye on it just in case. Thanks for watching!

@danreynoldsphotography2735

4 жыл бұрын

@@DroiMedia What do you mean wire both ends? It's ok to run all 4 wires into the same power source?

@DroiMedia

4 жыл бұрын

@@danreynoldsphotography2735 so far so good. I asked some folks with more experience than me about wiring and they told me wiring both ends helps distribute the heat and voltage/electricity (my first run through where I only wired one end got WARM with extended use). So my recommendation is wiring both ends, BUT, you absolutely do not have to do it to make this build work. Thanks for asking and let me know if you have any other questions!

@danreynoldsphotography2735

4 жыл бұрын

@@DroiMedia Hey I just noticed you are in Normal/Champaign. Peoria here!

@DroiMedia

4 жыл бұрын

@@danreynoldsphotography2735 sweet! I'm not in that neighborhood often but next time I am I'll let you know and maybe we can grab a cup of coffee or something (presuming of course this quarantine ever ends haha)

Do you have any extra end caps that I could buy from you? I don't want 98 extra laying around.

@DroiMedia

4 жыл бұрын

Yeah! Shoot me an email (should be up in my channel info) and we'll get that taken care of!

@Bono6234

4 жыл бұрын

DroiMedia emailed!

Well done ,can you make battery powered?

@DroiMedia

4 жыл бұрын

Thanks! And yeah! Any battery with a standard 12v output should work!

@casroy777

4 жыл бұрын

Sony np 970 batteries have 7.2 volt output but my led panels are working ,how?sorry for dumb question but this subject is out my knowledge.I was looking for battery powered led panels and found your video . And your video was very useful ,now I wanna make battery powered tube light too : )

@DroiMedia

4 жыл бұрын

You might be able to find a lower voltage LED strip, or you could possibly utilize a different battery source

@kennmossman8701

4 жыл бұрын

Strangely enough while the answer is yes that is complicated though the largest factor is the desired run time which dictates the AH of the battery

Can those light be wired directly to a 12v battery from my ice fishing flasher?

@DroiMedia

2 жыл бұрын

I don't see why not, try it out!

Is the wire at both ends really necessary? Could you not just solder to one end of the LED strip?

@DroiMedia

3 жыл бұрын

Not necessary but when I did some original tests only wiring one end caused it to get REALLY warm. The additional wiring allows for the current to continuously move, so there is no (or less) heart build up.

@threepe0

3 жыл бұрын

@@DroiMedia that makes perfect sense, and after I asked I started to wonder if it had something to do with current or maybe only half the lights being driven. Thanks so much for the reply and helping me understand!

@DroiMedia

3 жыл бұрын

Happy to help, there's more info buried up in the comments so it might be worth perusing those to check some things out. Happy DIYing!

Any other good sites to buy frosted acrylic tubes from? I'm in Canada.. the USD is a nightmare :p

@DroiMedia

4 жыл бұрын

I THINK they sell similar ones on Amazon, I'm on my phone right now but I'll get back to you later when I'm back around a computer, I've got some others bookmarked I think.

@stefankarabelov

4 жыл бұрын

@@DroiMedia sounds great!

@DroiMedia

4 жыл бұрын

@@stefankarabelov Hey! I can't find the link I thought I had bookmarked, but you should be able to search "acrylic tubing" or "clear acrylic tubing" on Amazon and find a decent priced one that's the right size: amzn.to/3eBLskF - let me know if you have any questions about potential ones, I don't want people buying the wrong stuff on my account :)

A 4' quasar LED tube is $100 on amazon which is basically $25/ft. How do these compare in brightness?

@DroiMedia

4 жыл бұрын

all Quasar brand tubes I've used will beat these in brightness, but I think the ones you're talking about are just the tubes and you'll need a housing (like an old KinoFlo shell or whatever) to mount them. These are fully self contained, other than power, much like the Q-LED line - which I believe are like $75/ft. If you can buy QS tubes then I recommend you do so - they are pro quality lights - but if you're interested in doing the DIY route these are an option to consider. Thanks for watching! :)

If you don't want 360 degree light consider using a thin flat piece of wood and mounting the strips to the wood on one side.

@DroiMedia

4 жыл бұрын

Kenn, thanks for the input - one of my iterations used some of the u-channel pieces that you can mount LED strips with, adhered to just one side of the tube on the inside. Ultimately it didn't provide as much light (fewer LEDs). This is a really solid idea though and one I think could work out with the right solution - I just haven't found it yet. Thanks for watching!

Hey any chance you could link me to some rgb led lights that will be usable in the same way for this project? Thanks!

@DroiMedia

4 жыл бұрын

Hey! I'm currently using this RGB strip (amzn.to/2O4aYn1), with these additional pieces (amzn.to/2NCVYgZ) - no samples yet and I don't have a finished product that I'm REALLY pleased with, but I'll post/share that when I get there. The build should be the same but with just 4 wires instead of the 2, hence the other set of connectors.

@jimmyb2687

4 жыл бұрын

Thx so much!

How can I make this rechargeable? Great video

@DroiMedia

4 жыл бұрын

Thanks! And no clue about making it rechargable, that's unfortunately beyond my capabilities.

@Quinterotheis

4 жыл бұрын

No problem I'm trying to come up with something at least battery operated

@DroiMedia

4 жыл бұрын

Cool cool, you could definitely power these off a battery of some kind just need to make sure the amps and everything are correct for the battery output.

Could i use this for light photography? Would I just connect a power bank to it?

@DroiMedia

3 жыл бұрын

yeah! Like for long exposure light paintings?? If so I would love to see you do that - and it should work just fine. I normally connect mine to a small external battery that way they are super portable, and while I leave mine on stands you could definitely run around with some connected to a battery.

How does wiring at both ends cut down on heat?

Do you still have end caps left over that you can give? I obviously don’t want to order a 100 😆

@DroiMedia

4 жыл бұрын

I should - hit me up w/how many you want via email: droimedia@gmail.com

@christiango604

3 жыл бұрын

@@DroiMedia how much wouldd you charge for 10? and a wooden dowel rod?

@DroiMedia

3 жыл бұрын

@@christiango604 hey! shoot me an email and we'll chat - droimedia [at] gmail.com

muy buenas, como las harías recargables?

I never saw this in my life super Where to get this diffuser

@DroiMedia

4 жыл бұрын

Which diffuser? The acrylic tubing?

@Akshay-pe4fp

4 жыл бұрын

@@DroiMedia yes sir cover

@DroiMedia

4 жыл бұрын

Link for all the materials is in the description! You can also find similar products over on Amazon.

How much would it be for you just to make it for me and ship it?

@DroiMedia

3 жыл бұрын

Heya! I would have to look at pricing and get back to you, what length and light color do you want? I honestly probably wouldn't have time to do it until October, just FYI

Serious question, Does it help to solder/Connect both ends of the strip to the power adapter? Love your assistant btw PD: have you tried white acrylic? How does it look?

@DroiMedia

3 жыл бұрын

heya! so I mention somewhere but in running my tests my 'soldered only at one end' lights got WARM, like borderline hot, especially at the base. So I asked around and some folks told me that the 'loop' style system that I ended up using would help diffuse the current more throughout the entire light. So my lights currently do not get nearly as warm as they used to with this method. Hope that helps answer your question! And thanks, all my furry assistants are lazy, annoying, and adorable AF :D :D - as for the white acrylic, I have not used it, just that semi-clear / opaque one you can see in the video. Thanks for the question!

@bidomo

3 жыл бұрын

@@DroiMedia oh sorry, maybe I didn't pay close attention to the video, as I was planning my lamps myself with inspiration in your work. Thanks for the reply!

@DroiMedia

3 жыл бұрын

No worries I can't remember if I mention it in the video or in a comment somewhere, coming off a hot exterior shoot so my replies sound way grumpier than they should 😊

Brother how many voltes have you made light of 12 volts, 4 volts dc

@DroiMedia

2 жыл бұрын

Heya! Not sure I quite understand the question - any chance you could re-phrase it? Happy to help, just want to make sure I can answer your question correctly! :)

@ministudio2122

2 жыл бұрын

@@DroiMedia means the light you have prepared is it in 12 volt dc or in 4 volt

@DroiMedia

2 жыл бұрын

@@ministudio2122 I THINK it's 12v, keep in mind my math is all done on scratch paper and I'm not trained professionally by any means in this. Hope that helps a little!

Is there a way to make one without soldering anything ?

@DroiMedia

4 жыл бұрын

Hey! You could probably find some solderless connectors to use, I can't speak to how safe or reliable they would be but if you went with that route you could use some of that shrink wrap stuff on the end (that you heat up and it shrinks and seals everything) to potentially strengthen the connection.

@bidomo

3 жыл бұрын

As far as I know, you can just use one end of the led strip, which comes with ready to use power adapters, I actually don't know why he soldered the other end, but either way, soldering is pretty easy, I'm actually a magician with the soldering Iron, but I know 20 cents of electronics...

How many meters did you end up using for one led tube?

@DroiMedia

4 жыл бұрын

Hi! I mention this in the video but 5m works for a 3 foot long tube.

@ItsJustWolff

4 жыл бұрын

@@DroiMedia yea but u still cut off some but ill guess it wasnt much then but thx

@DroiMedia

4 жыл бұрын

I don't remember how much it was, less than 9" I THINK

Rgb w use cool 😎

Which tube use in this project.

@DroiMedia

4 жыл бұрын

I used this frosted acrylic tubing: bit.ly/2lCamdL