How To Make RGB LED Tube Lights for Cheap (Quasar Science Light Knockoff)
Тәжірибелік нұсқаулар және стиль
In this video I show you step by step how to build your own DIY quasar science light on a budget. Each one roughly cost me $35-$40 which is absolutely amazing considering the quasars are $500 for the full rainbow lights 😯 The reason I say these are the best I've seen is because they are matte finish, they are fully addressable RGB, they are app controlled and they provide light 360 degrees which is awesome! You can use lights like these in music videos, KZread videos, Photography and soooo much more. You can piggy back them to each other or you can split them so they all have the same effect in sync. The possibilities are endless! This took me much longer than expected because I had to test many different materials to make the absolute BEST possible! Thank you all for the support 🙏
I will definitely be making more of these in the future!
*Product Links
T12 Tube: bit.ly/BWVtubes
Dowel: amzn.to/3mHtilc or bit.ly/BWVdowel
LED Lights: amzn.to/3mBt4wd
Extra Power: amzn.to/3h7vhy4
Extra Controller: amzn.to/38oicMY
Vinyl: White - amzn.to/3h75vdz Black - amzn.to/2KknMbo
Paint: amzn.to/3rjfS2x
Sand Paper: amzn.to/2LZTawf
*As an Amazon Associate I earn from qualifying purchases without any additional charge to you.
*Any money I may make via Affiliate or other means I will reinvest into my KZread channel. Thank you for the support.
Time Stamps
Start - 00:00
Materials you'll need - 01:08
How to build these lights - 05:01
Final thoughts and Testing - 15:57
*Some of the parts in my PC
RGB Cables: amzn.to/34sX3At & amzn.to/2EDIboN
Lian Li 011 Dynamic Case: amzn.to/312nhIv
Ryzen 7 3700X: amzn.to/3h5eA5q
Lian Li AIO: amzn.to/2Tp2pq8 or amzn.to/2WEoYcc
B550 Aorus Pro AC: amzn.to/2CBdhfB
Ballistix RGB Ram: amzn.to/34vR0v1
Inland 1TB NVMe SSD: amzn.to/38Yk4Mr
MSI 2070S: amzn.to/2TqX4Ph
Corsair 750W PSU: amzn.to/392oVfw
*Camera I use: amzn.to/3481zTP
*MIC I use: amzn.to/3cCUZZc
Software I use: Filmora X, Audacity & Paint(.)net
Follow me on Instagram and twitter
/ buildswithv
/ buildswithv
For business inquires: business@buildswithv.com
**Your results may vary. I am not responsible for any damage. Do this at your own risk.
#DIYtubelight #TubeLights #DIYQuasarTubeLight
Пікірлер: 103
If you could improve one thing about these tubes lights, what would it be? Thanks for watching! 🙏 Time Stamps Materials you'll need - 01:08 How to build these lights - 05:01
@yoda_playz3060
3 жыл бұрын
am so damn proud bro 2.05k subs 🥳🥳🥳🥳🥳🥳
@BuildsWithV
3 жыл бұрын
@@yoda_playz3060 thanks so much 🙏
@BatEatsMoth
3 жыл бұрын
Buy diffuser tubes if you can find them; it saves you time.
@ellenlara7026
3 жыл бұрын
Make it portable...do a usb instead of a plug
@bikesbeersbeats
2 жыл бұрын
Use electrical tape instead of sticky tape.
Great video! Me and my friends played a drinking game that we take a shot every time he says “basically“ ….aaaaand BASICALLY we’re hammered. lol
@BuildsWithV
3 жыл бұрын
Nice! Happy to help 😅
Basically we came for the basics. Great tutorial thorough bro thanks!!
This is awesome! Thank you!
Love your idea your genius bro
This whole thing is 🔥!
@BuildsWithV
3 жыл бұрын
Thank you 🙏
Very cool 👍😎👍
Thank you so so much!!!!!! This helped out a ton!!! Used this for my science fair project. My question was how do I make a interactive light show. I looked up videos and this one came up. Worked greatly!!! Thank you so much!
@BuildsWithV
Жыл бұрын
Oh wow I never thought anyone would use it for a project like that! That’s so cool, glad I could help 🙏🙌
Love this video it's what I've been looking for. I kinda resent the concept of paying more to diffuse the leds than the cost of the lights themselves. Wondering if you can get thinner tubes even hosepipe style ones to make it a little less bulky.
great vid!
Basically this is the basics for a basic tube light🗽
I did the same but 8 feet but I used Wax paper to cover and wooden bases with elbows to pass the cables and remain as a stand
Great job and great video
@BuildsWithV
3 жыл бұрын
Thanks so much 🙏
After watching a million diy videos, i Went and got some tube covers from home depot today. These are the best option IMO for govee lights since theyre 30mm apart.
@pura_boda
Жыл бұрын
If I want to make tubes of 1 or 1'20 meters long, what si the length of the led? How long is that in the video? The link to the tube doesn't work for me. I have govee lights in my studio and are great! What do you mean about 30 mm apart?
Hey man, great video! I've been looking for something like this! Question though, is it bright enough for backlight like in those streamer vids? Is there a way to make brighter?
so BASICALLY this is a tube light tutorial
The back is just another cool effect
@mikisafe2905
3 жыл бұрын
Ikr
Could you update the description because a few of the items are now not available. Great video tho mate
🔥🔥🔥
Nice :)
@BuildsWithV
3 жыл бұрын
Thank you! Cheers!
I want to do a smallwr scale version of this in my pc, do they generate much heat?
Hi, I secured way to setup 10 led tube together and control them all together with an app , you suggest what / how to link them and control together and what to use for wifi controller and power supply ? Thanks
Merry Christmas "V"🎁⛄
@BuildsWithV
3 жыл бұрын
Merry Christmas to you too
What is the difference in black or white vinyl paper ?
can you make them strobe or react to sound?
Pretty good! I wonder about the brightness though. They don't seem bright enough for use in an otherwise well lit environment. If these are the only lights in the scene they may work, but even then I don't think they would put out all that much light. Really good idea for DIY tho!
@BuildsWithV
3 жыл бұрын
That may be true. Haven’t tested these in many light situations but I did have my ring light on full brightness and these were still vivid. Any brighter and I’d say they’d be washed out honestly. Thanks so much 🙏
@AfoteyAnnum
3 жыл бұрын
@@BuildsWithV thank YOU for creating this video!
Basically Govee Dream Color leds would be perfect for this with a app that doesn't suck
Good job, next time instead of wrap, use frosted glass spray paint, its absolutely perfect for this job
@BuildsWithV
Жыл бұрын
I was going to but wasn’t sure how well it would spread the light. I think the wrap did it really nicely. Still holding up till today
These would be killer if you made a stand for them
2:25 ws2811 for 12v supply and ws2812b for 5v are the best and cheapest led strips.
how do you control these if you dont have a smartphone ????
Hey dude i just wanted to ask if you had to guess what is the wattage for the lian li strimer cables as i have a 750w powersupply and the estimated wattage on pc part picker is 518w without the cables so i just wanted to make sure its gonna be safe. also nice vid :)
@BuildsWithV
3 жыл бұрын
For the Strimer cables I’m not too sure what they’re estimated at unfortunately. It should be perfectly fine, I have a 750w bronze psu as well and tons of other stuff in my PC without any issues. Upgrading to 850w gold soon to be safe cause I’m putting a 3080 in it, otherwise it’s fine
@Benjymain
3 жыл бұрын
@@BuildsWithV Ok Thanks :)
Any thoughts on sanding the exterior of the tube vs using vinyl? I wonder how it would compare in brightness to your eyes. Lol Tbh when you finished wrapping it in vinyl I clapped! not at all an easy feat, well done
@BuildsWithV
3 жыл бұрын
I actually tried the sanding method and unfortunately the leds were still very visible through it. I tried various grits as well. I also tried the paint method and that works about as good as vinyl but a bit messy. The vinyl gave it a nice texture and overall the beat look with the matte finish. I did try gloss as well and it looked great but too shiny. Basically just settled on matte vinyl and looks great. Thanks so much 🙏 There’s a few small bubbles in the vinyl but 🤫 don’t tell anyone 😂
@jaceace32
3 жыл бұрын
@@BuildsWithV i appreciate that reply. Just about to get going on a 1.7ft tube with my 144 3.3ft strip folded back to back and hopefully centered in the tube by suspension. That or cutting down and placing the half strips next to each other and taped to one side of the tube. Wanting to use this as a sconce so not too worried about the back side but more concerned brightness... now i'm kinda wondering if 360 light will give me more illumination then back to back
@BuildsWithV
3 жыл бұрын
@@jaceace32 I’m honestly not too sure which way would provide the most like honestly. I wanted 360 degree lighting so I can show off the front to the camera and the back can illuminate the background or whatever it is I’m shooting. Since only about 50% of the leds will be facing the front I’d assume laying them down and facing as many as possible towards the front would provide the brightest lighting.
Would be beter to use the frosted vinyl as opposed to white. You're losing a lot of light output having an opaque layer. As well, using an led strip that is 60led/m as opposed to 30
Name of tat transperent pipe look like cylindrical
How many ft u need to wrap all the stick 32?
@BuildsWithV
3 жыл бұрын
Each stick will take 16 feet
Is there any flickering on higher frame rates? ie 60p / 120p with a shutter speed of 1/125 - 1/250
@BuildsWithV
3 жыл бұрын
I don’t believe I saw any flickering at 120 but I will check. 240 there was (on my iPhone)
@BatEatsMoth
3 жыл бұрын
You shouldn't. It uses a DC adapter, so you don't get that 100% NVF modulation at 120 Hz like you do from direct AC.
@BuildsWithV
3 жыл бұрын
Yeah I tried 240 again (forgot to get back to you) and still no flickering. So looks great
@ArcherVideo
2 жыл бұрын
I’m trying to get started with the LED tubes while having zero knowledge of LED specs. I’m wanting to use these tubes for sports videos with a decent amount of slow motion 1/250 or even faster shutter speed. What spec/stat should I be looking at when buying LEDs to know if the refresh rate can handle this shutter speed without flicker?
Is it 16ft per tube or 32ft per tube of rgb strip
@dmo848
3 жыл бұрын
16 he bought 2
It looked like the holes in the caps that came with the tubes were centered. Is there a reason you didn't just use the centered holes so that the lights would be in the middle instead of on one side. Wouldn't that have made the LEDs diffused evenly and not had a back side of the tube?
@BuildsWithV
6 ай бұрын
I think I accidentally did that, I don’t remember at this point my reason 😅 in the end tho, the light was not diffused enough so I ended up pushing the dowel towards the back side into those grooves I made and then it diffused fine. Overall this was mostly an experiment and a learning experience. There are many things I’d do differently for sure
@cdsentone3832
6 ай бұрын
@@BuildsWithV I wonder if you could add tubes of white baking paper or waxed paper on the inside of the tube to add more diffusion.
I saw a similar video but by just covering a fluorescent light with coloured versions of these tubes.
Why sand it if you're wrapping in vinyl? Couldn't you also use wax paper?
@BuildsWithV
2 жыл бұрын
I sanded the first one off camera because I planned to paint it but also to diffuse the light a bit more. Wanted to make sure both were the same so I still sanded the second one. Can use wax paper but when I tried it, it bled more light than I wanted. The wrap wasn’t perfect and I’m sure there’s way better ways of doing this. I kinda went in blindly and this is what I came up with 😅
why would u buy a clear tube guard and do extra work instead of just buying a white, frosted, or diffuser tube guard?
@BuildsWithV
9 ай бұрын
There were none available at the time. This was just a little experiment for myself
i watched this after i build my own with old led tube light
@BuildsWithV
3 жыл бұрын
Nice! How did yours turn out? What did you do different?
@novakchong3980
3 жыл бұрын
@@BuildsWithV it's fine but mine is transparent without the wooden rod and the base is cement, i don't have proper tools so i just do it anyway, it almost cost a thing im mean all parts are scraps
What r u doing step V. 5:19
@BuildsWithV
3 жыл бұрын
👀🤷♂️
what was the point of sanding it?
@BuildsWithV
2 жыл бұрын
Just so the paint can stick better
if this mans watch was on any tighter his fingers would be more blue then the rgb
Hi you live in Toronto ?
@BuildsWithV
2 жыл бұрын
Hello, I do not. I live near Cleveland, Ohio. Not too far from Toronto tho
what happend to your QL fans
@BuildsWithV
3 жыл бұрын
I put them in another PC. Still figuring out what I wanna do with this Pc as far as Fans and all that good stuff.
@Xoul-fp4zd
3 жыл бұрын
@@BuildsWithV ah ok nice
Pretty sure you could have just run a single 4ft line of LEDs on a flat length of wood instead of wrapping 16ft of them around a dowel.
@BuildsWithV
3 жыл бұрын
Yeah you can and it works okay but it’s not 360° which I could have solved with some soldering etc. but I wanted to try it thins way and I needed them to be brighter
@expression3639
Жыл бұрын
Running them along a dowel and making sure the LEDs are offset properly would have worked too. The chips on my strips have rather long traces which makes them difficult to wind around a dowel like this so if I end up doing a project similar to this, I will have to do as Neon Specter suggested. My strips have 32 LEDs per meter but I know that some LED strips are even more dense. The best solution will highly depend on what kind of strips you have.
wax paper will let more brightness come out of the tube
@BuildsWithV
8 ай бұрын
Yeah back then I tried it but I think I just used too many LEDs cause no matter what I tried I couldn’t get the individual LEDs to not be visible. Ended up using this and it worked but kinda dim. Maybe some day I’ll give this another shot.
"colors are off..." then they are not the best one are they? next!
rainbow lights lol no colour at all ????????
So basically they aren't bright at all..
@arthurhar1616
2 жыл бұрын
bro stop crying go buy some grovee lights💀
Basically......dude try another word. You gave me a headache, thanks 🤕
@BuildsWithV
2 жыл бұрын
Take some ibuprofen 🤷♂️
omg i can't watch this brutality for long !! worst tutorial ever 🤣
@arthurhar1616
2 жыл бұрын
Are you high or sum fam?