I'm happy to see that I'm not the only one that has a little trouble with the brush barrels on these. These were much easier to do when I was a kid. I usually use a metal cookie sheet when taking apart and reassembling chassis. It helps to contain flying parts but doesn't catch them all. Great video. Thanks for doing these videos.
@slotslidershoslotcars
Жыл бұрын
Same here I use a small cookie sheet with a micro fiber or hand towel to catch any parts that slip out of my ig sausage fingers🤣🏁
@aloissenefelder12 жыл бұрын
Been watching you for years. Great information!
@slotslidershoslotcars Жыл бұрын
I'm with ya on all counts. Love the G-plus cars, love the 1970's F1's and that Leiger is too cool
@glennstock59963 жыл бұрын
It would have been good to see a dyno test of the before and after tune-up. Love your videos, keep up the good work.
@darrinpennington8 жыл бұрын
Glad I'm not the only one who has trouble with motor brush springs. Lost three trying to reassemble xtraction chase
@michaelragland4762
7 жыл бұрын
Agreed. I'm glad I had the foresight to buy several G-Plus springs from a guy who sold new old stock parts before I started to restore my first G-Plus chassis. Had a few that got away from me too. lol
@andrewluchsinger
6 жыл бұрын
I keep a good supply of the springs just in case of one of the damn springs flying off into oblivion.
@Metal-Possum
6 жыл бұрын
Stay away from the Mega G chassis, the brush springs in those are microscopic in comparison. Not my favourite chassis, not by a long shot. The xtraction only gave me grief while trying to put the armature back in without disturbing the brushes, but I have the hang of it now.
@Overkeil7 жыл бұрын
thanks for sharing... i love the work you are doing... KEEP IT UP!!!
@slotcarcrazy
7 жыл бұрын
+Len Overkeil thank you Len
@Overkeil
7 жыл бұрын
I HAVE LOVED HO-SCALE RACING SINCE KINDERGARTEN... SO YOUR CHANNEL IS LIKE GOING HOME AGAIN... AND YOU ARE RIGHT ENGINE SPRINGS ARE THE WORST... YOU HAVE A SUBSCRIBER HERE... MAY BUILD ME ANOTHER SET AGAIN...
@SuperDaveSlotCars8 жыл бұрын
Thank you Troy.
@bluesimon13ify4 жыл бұрын
Great looking cars you bought, I prefer 1/32,😀😀😀
@kevynbrownell7194 жыл бұрын
Should a showed what made the speed shifter the car it was. Could go both directions on track. I like mine. It goes fast.
@MikeRemvidas8 жыл бұрын
I too have trouble with them brush clips... I do the same as you with each chassis off E~Bay 🏁🏁🏁
@RCFlyBy911
3 жыл бұрын
@Otis Saint Will have to check that out ‼️👌🏼👍🏻 Thank you
@RCFlyBy911
3 жыл бұрын
@Madden Bryce Going to check it out , Thank you ✌🏻👌🏼👍🏻
@auroraafxsweden53005 жыл бұрын
The barrelholder clip is my big problem. .. I am learning. .🏁🏁
@domer99 Жыл бұрын
It looks like you were cleaning the com with a wire brush. We used to use a fiberglass pencil to clean the com while under power. Have you tried that method? Love the G Plus. Nice video, thanks.
@jettafixer75 ай бұрын
I think the G-plus was one of the hardest to work on. Brushes were a big problem.
@daytch94856 жыл бұрын
What are the best track magnets for the super g and g+, cause my stock ones are garbage
@slotcarcrazy
6 жыл бұрын
+d aach I've only used stock magnets on these cars
@garyjones40396 жыл бұрын
Hey I’m just starting out for the first time I’m not what are the best tools to use
@slotcarcrazy
6 жыл бұрын
Checkout tools of the trade video I did it will help
@bryanwilmot6 жыл бұрын
I have rebuilt many slot cars could you give me a sight for tycoo tcr slot car made in the 70s ty
@slotcarcrazy
6 жыл бұрын
+Bryanw2 I have never did anything with the tcr car but we will have to in the future
@prav4013 жыл бұрын
I'm watching this video now realizing it's 5 years ago man prices were a lot cheaper then weren't they?
@andrewluchsinger6 жыл бұрын
TGFRK Thank Goodness For Repair Kits
@ZombieObsidian7 жыл бұрын
Sounds like you pulse the throttle all the time? If so why do you do that over being smooth with it?
@slotcarcrazy
7 жыл бұрын
+Jason Dickson my controller is really squeaky it makes it sound more that it really is
@ZombieObsidian
7 жыл бұрын
a few drops of braid juice or Ford atf than wipe with your finger fixes the contact sqeek. normal oil on the other moving parts
@alyssasnaturesanctuary8 жыл бұрын
Love you videos. Just wondering how to ask you questions. do you have an email? of how would I go that.
@slotcarcrazy
8 жыл бұрын
My email is sntozman@gmail.com to answer your other I shoot my video on my phone and edit on the fly
@alyssasnaturesanctuary
8 жыл бұрын
no, the software you are using for lap time/speed...
@slotcarcrazy
8 жыл бұрын
Sorry about that I us trackmate
@prav401 Жыл бұрын
$33 for the ligier??? I wish it was that cheap now.
Пікірлер: 37
I'm happy to see that I'm not the only one that has a little trouble with the brush barrels on these. These were much easier to do when I was a kid. I usually use a metal cookie sheet when taking apart and reassembling chassis. It helps to contain flying parts but doesn't catch them all. Great video. Thanks for doing these videos.
@slotslidershoslotcars
Жыл бұрын
Same here I use a small cookie sheet with a micro fiber or hand towel to catch any parts that slip out of my ig sausage fingers🤣🏁
Been watching you for years. Great information!
I'm with ya on all counts. Love the G-plus cars, love the 1970's F1's and that Leiger is too cool
It would have been good to see a dyno test of the before and after tune-up. Love your videos, keep up the good work.
Glad I'm not the only one who has trouble with motor brush springs. Lost three trying to reassemble xtraction chase
@michaelragland4762
7 жыл бұрын
Agreed. I'm glad I had the foresight to buy several G-Plus springs from a guy who sold new old stock parts before I started to restore my first G-Plus chassis. Had a few that got away from me too. lol
@andrewluchsinger
6 жыл бұрын
I keep a good supply of the springs just in case of one of the damn springs flying off into oblivion.
@Metal-Possum
6 жыл бұрын
Stay away from the Mega G chassis, the brush springs in those are microscopic in comparison. Not my favourite chassis, not by a long shot. The xtraction only gave me grief while trying to put the armature back in without disturbing the brushes, but I have the hang of it now.
thanks for sharing... i love the work you are doing... KEEP IT UP!!!
@slotcarcrazy
7 жыл бұрын
+Len Overkeil thank you Len
@Overkeil
7 жыл бұрын
I HAVE LOVED HO-SCALE RACING SINCE KINDERGARTEN... SO YOUR CHANNEL IS LIKE GOING HOME AGAIN... AND YOU ARE RIGHT ENGINE SPRINGS ARE THE WORST... YOU HAVE A SUBSCRIBER HERE... MAY BUILD ME ANOTHER SET AGAIN...
Thank you Troy.
Great looking cars you bought, I prefer 1/32,😀😀😀
Should a showed what made the speed shifter the car it was. Could go both directions on track. I like mine. It goes fast.
I too have trouble with them brush clips... I do the same as you with each chassis off E~Bay 🏁🏁🏁
@RCFlyBy911
3 жыл бұрын
@Otis Saint Will have to check that out ‼️👌🏼👍🏻 Thank you
@RCFlyBy911
3 жыл бұрын
@Madden Bryce Going to check it out , Thank you ✌🏻👌🏼👍🏻
The barrelholder clip is my big problem. .. I am learning. .🏁🏁
It looks like you were cleaning the com with a wire brush. We used to use a fiberglass pencil to clean the com while under power. Have you tried that method? Love the G Plus. Nice video, thanks.
I think the G-plus was one of the hardest to work on. Brushes were a big problem.
What are the best track magnets for the super g and g+, cause my stock ones are garbage
@slotcarcrazy
6 жыл бұрын
+d aach I've only used stock magnets on these cars
Hey I’m just starting out for the first time I’m not what are the best tools to use
@slotcarcrazy
6 жыл бұрын
Checkout tools of the trade video I did it will help
I have rebuilt many slot cars could you give me a sight for tycoo tcr slot car made in the 70s ty
@slotcarcrazy
6 жыл бұрын
+Bryanw2 I have never did anything with the tcr car but we will have to in the future
I'm watching this video now realizing it's 5 years ago man prices were a lot cheaper then weren't they?
TGFRK Thank Goodness For Repair Kits
Sounds like you pulse the throttle all the time? If so why do you do that over being smooth with it?
@slotcarcrazy
7 жыл бұрын
+Jason Dickson my controller is really squeaky it makes it sound more that it really is
@ZombieObsidian
7 жыл бұрын
a few drops of braid juice or Ford atf than wipe with your finger fixes the contact sqeek. normal oil on the other moving parts
Love you videos. Just wondering how to ask you questions. do you have an email? of how would I go that.
@slotcarcrazy
8 жыл бұрын
My email is sntozman@gmail.com to answer your other I shoot my video on my phone and edit on the fly
@alyssasnaturesanctuary
8 жыл бұрын
no, the software you are using for lap time/speed...
@slotcarcrazy
8 жыл бұрын
Sorry about that I us trackmate
$33 for the ligier??? I wish it was that cheap now.