Just in case you wonder if you save people $$ and time by putting out these videos, you just did. Thank you kindly‼️‼️

All other fix-it channels should watch this video to see how they should be done. Perfect.

@searspartsdirect

5 жыл бұрын

Thanks for the positive comment. We're glad to see that our hard work on this video is noticed and is helping.

One of the best troubleshooting videos I've seen. Thank you for the professional guidance.

@searspartsdirect

5 жыл бұрын

We're glad to hear that you liked the video. Thanks for the positive feedback.

This video saved my life on Christmas Eve! Error code 31 appeared before I started to prepare my Christmas meal. Easy fix loose wire in back. Thank you so much!

@searspartsdirect

5 жыл бұрын

We glad to hear that our video helped. Thanks for letting us know what you found.

Amazing you can walk us through diagnosing this appliance in as little as 4 minutes where others are much, much longer winded. BTW, I found the short and fixed the problem. Thanks a lot.

Thank you SO very much! My door issue was caused by a loose connection! It's as good as new and I'm thrilled!!!

@searspartsdirect

4 жыл бұрын

Thanks for letting us know what you found. We're glad to hear that you got your range fixed.

I trust this guy to fix anything.

This was so helpful. Even my husband understood it.!! .

Video helped a lot, followed the directions. Used the multimeter all checked out I’m assuming it was just a loose connection. 😊 thank you.

What if the f31 code goes away when I turn the circuit breaker off and back on?

This is how all trouble shooting videos should be done. Perfect

Is the F31 code dangerous, like over time. I usually unplug it and plug it in again and again, and each times it works, then it reverts back. Now it's just showing weird numbers, sometimes it starts counting. What could be wrong? Is it possessed?

@searspartsdirect

3 жыл бұрын

The F31 code typically isn't dangerous but when your range displays that code, you should unplug the range and repair the problem or have the range repaired by a technician. When the control is just showing weird numbers, you'll likely need to replace the control or have a service technician replace the control. If you replace the control yourself, be sure that you unplug the range before beginning the repair.

Thank you, sir.

Amazing video keep up the good work

Thank you 🙏 Saved a lot of Men out here Especially fathers when our daughters want to bake us cookies they just mixed up Breathing down our necks 😂😂😂 Thank you again

I replaced the temp sensor and the control board, but the F31 code comes back once in a while. If I unplug from the outlet, wait 10 seconds, then plug back in it goes away. I'm about to replace the wire harness too but is there any other chance it could be something else?

I get the F30 on my Kenmore oven as the oven heats up. sensor ohms correct and no shorts. Could it still be the senor at higher temps or the board? If it was the sensor would it stay at an F30.

Best yet!

Hi, so I was following your method to troubleshoot F30 code. I tested the wires and it measured up to 1089-1090. I even replaced the control board. But my oven will not work... Every time I try to turn it on it the stove cuts off completely.

Thank you

Great video, thanks a lot 👍🏼

I took the sensor out and just cleaned it off in some vinegar, baking soda and water after the resistance tested ok. Good as new.

Thank you so much for making this video. I ohm out sensor it was good. I order new control unit from Amazon , installed it and works prefect. I have always been handy at fixing things, Never worked on stove other then replacing elements for oven or stove top. This was a first for me, Went like clock work. If you have a Manuel amp meter where you have have to choose ohms number setting, put your meter on 2k to get a reading.

Thanks for this video! We were able to troubleshoot at home & keep on baking! Also it was a teaching opportunity with my son on how to use a multi-meter!

Hi, thanks for your help you are the best. In my case I found the ignaiter on a gas stove was broken or damaged. I unplug it and reset it after I replaced the ignaiter. Work great and the code 31 is gone. Did I got 10? 😳

@searspartsdirect

2 жыл бұрын

Yes. You got a 10. Good DIY troubleshooting.

All I did was unplug it and plugged it back in and it worked

@searspartsdirect

5 жыл бұрын

Sometimes the simple fix works. Thanks for letting us know what you did to fix the problem. We're glad to hear that you got the range fixed.

@Tubermich56

5 жыл бұрын

Worked for me too. Saved my sanity since my fridge is acting up also .

@searspartsdirect

5 жыл бұрын

@@Tubermich56 Let us know if you need help diagnosing and fixing your refrigerator.

Thanks great advise

Thank you!

Best video

What if my sensor ohm’d out at 1.073, at the sensor itself?

Light switch is shorting. Jiggle a few times while unplugged and voila 🎉

What if the oven starts smoking?

If it measures 1065?!

WOW! What a huge help. thanks a lot for this video. JJ

@searspartsdirect

5 жыл бұрын

We're glad to hear that you liked the video. Thanks for the feed back.

Gracias senor exelente informacion

@gladysbarba2425

4 жыл бұрын

Me lo podrías explicar sencillo?

I have a really old Kenmore stove that suddenly did the same thing so I’m going to check all the connections and then get a temperature sensor and if that’s not it I’ll get a new used stove Because my stove is at least 35 years old

Thanks a million

Thank you for the professional guidance. It helped me save money and time.

Show about fault F68

Does the oven has a reset button somewhere? cause replasing the board, heat sensor did not fix issue?

@searspartsdirect

4 жыл бұрын

Let us know the model number of your range and we'll check to see if your model has a high temperature limit switch with a reset button.

@sydneydurbin2114

4 жыл бұрын

@@searspartsdirect Replaced the board and the probe was showing the proper ohm, still getting the F30 model # fgfl67dcg

@searspartsdirect

4 жыл бұрын

@@sydneydurbin2114 Unplug the range and check resistance through the temperature sensor probe wires that connect to the electronic oven control board (usually violet wires). If your meter doesn't measure proper resistance through the wiring and probe, then you'll need to find and repair the wiring break or replace the wire harness.

@RobertoSantos-hc5td

4 жыл бұрын

How to fix F50

Love it

I unplugged it and plugged it back in and it disappeared. Is my apartment going to blow up?

@SamBreitenbach-ej7cb

Ай бұрын

I dont think that will happen

My Range show E-27

My oven shows 1057.. When I cut the oven on it won't go higher then 260° not sure what's going on

@searspartsdirect

3 жыл бұрын

Your details seem to indicate that the control display is showing oven temperature in Celsius instead of Fahrenheit. Follow the instructions in your owner's manual to change the temperature display back to Fahrenheit. If you don't have the owner's manual handy, you can likely find an online version on our website. Key the model number of your range into the search field on this page: www.searspartsdirect.com/ . If you need more help let us know.

@ericminco8204

3 жыл бұрын

@@searspartsdirect Hi there, I needed some assistance please. Your video is very helpful however it does'nt address how t go about changing the wiring harness. I've checked the reisitance Ohms and I don't get a reading from the wiring harness. I've tried looking up "replacing wiring harness" but cant find anyting on it. the wires are not damaged either nor are they kinked so I don't know what else to do to repair the wires to the temperature sensor. Can you help me out?? thanks

@searspartsdirect

3 жыл бұрын

@@ericminco8204 Let us know the model number of your range and we'll try to help you.

Hey can you come over and fix our oven

Anyone ever receive an F-10 code

My gas stove has PF code

@alvinwells5241

Жыл бұрын

Code f31

@SamBreitenbach-ej7cb

Ай бұрын

PF means there was a power failure and that's not a serious problem

Damn Cab, you lookin sexi neow! ;)

⁰no loop mo